Inside Weather 4 SEAT SOFA User manual

4 SEAT SOFA

Gather Your Eggs...
BACK PILLOWS
A
BACK PLATES
B
AAAA
B B
2x ARMS
C
C C
2x FRONT PLATES
D
EEEE
3x INNER SUPPORT BRACE
F
G
SEAT CUSHIONS
E
D D
F
36x SLATS
G
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.

You should have:
4x LEGS
4x CORNER BRACKETS
16x NEOPRENE
STICKY PADS
48x BUTTON HEAD HEX SCREW
(5 MM HEX BIT)
CENTER SUPPORT LEG
8x SET SCREWS
16x SOCKET HEAD CAP SCREW
DRILL + EXTENSION
5MM HEX BIT
4MM BALL HEAD BIT
3MM HEX BIT
USB CHARGER
Note: Drill may need to be charged before use
Note: Don’t be surprised if you find a few extra screws, washers and even an extra support brace
among your supplies. It’s just our way of being extra sure you have everything you need.

Step 1: Connect the Back Panels
Push the back panels together
to lock them in place.
Center
Brackets
Connected Back Panels

Align the arm and back panels
so that the metal frames meet
at a right angle. Lean the arm
slightly away from the back
panel. Lift the top of the back
panel and gently lower the
hook until it connects. Repeat
on both sides.
Step 2: Connect the Arms
Connect the Hooks
Stand the arm on its side.
Identify the corresponding hooks
located on the arm and back panel.
This is how they connect.
The connection is the same
for both sides
Next we’ll connect the back panels to the arms.
The process is identical for both arms.

Connect the Arms (Continued)
Place a corner bracket to connect
the back and arm panels.
Put a 5mm button head socket cap
screw in each of the three holes in
the back panel. Losely hand tighten
only for now.
Screws will be tightened after they
have all been placed.
Connect the corner bracket to the
arm by hand-threading a button
head socket cap screw into each
of the three remaining holes.
Once all six screws have been
connected, use the drill to fasten
each bracket until secure.

Step 3: Install the Inner Support Braces
You’ll Need: 3x INNER SUPPORT BRACES
12x BUTTON HEAD SOCKET CAP SCREW (5 MM HEX BIT)

Install the Inner Support Braces (Continued)
Make sure the edges are flush
Hand tighten before finishing with
the drill to make sure everything is
properly aligned.
Repeat for the other braces.
Line up the holes in the support
brace with the corresponding
holes on the frame.

Step 4: Attach the Front Plate
FRONT PLATES
CORNER BRACKETS
5MM BUTTON HEAD SCREWS
2x
2x
12x
You’ll Need:
In this step we’ll be adding the
front plate. But first let’s make
sure everything is ready!
NOTE: When attaching the front
plates, make sure the arrows in
the center of each plate point
in towards each other.
Attach a corner bracket to
the arm rest using 3 5mm
button head bolts. Hand
tighten only.
Repeat for other side.

Attach the Front Plate (Continued)
Set the front plate between the two arms as shown. Make
sure that the flap of excess fabric is facing the top of the
couch and hanging toward the inside of the frame.
This will ensure that the plate is rotated correctly.
Line up the holes in the support brace with the corresponding
holes on the frame. Insert the 5mm button head screws.
Make sure the edges are flush Hand tighten before finishing
with the drill to make sure everything is properly aligned.
Add 3 more bolts to the corner bracket.
Go back over each screw in the corner
brackets and center braces with the drill.
Tighten until secure.

Step 5: Install the Legs
Start by aligning the leg over the mounting holes. Insert
bolts into corresponding threaded holes as shown and
tighten by hand.
Note: if you have flared legs, make sure that each leg
points outward toward its respective corner.
Once each bolt is started by hand, use the
drill to finish securing the leg.
Repeat for all four legs.
4x LEGS
16x SOCKET HEAD CAP SCREW
You’ll Need: Note: Our legs are universal, and are used across
multiple products. All sofa and ottoman legs will
attach securely with 4 fasteners per leg.

Step 6: Install the Center Support Legs
Attach a center leg to the center brace. Add 4
set screws to fix the leg in place. The foot can be
adjusted for proper height. Repeat for other leg.

Step 7: Add the Neoprene Pads
Slats should look like the
diagram after the pads
have been added.
To keep the cushions from sliding
add the non-slip neoprene pads.
2 pads will be stuck onto a slat.
Only 8 of the slats of the sofa will
need pads.
Please see diagram for correct
placement.

Step 8: Place the Slats
DONE!
Step 9: Add the Cushions
Lay a slat in each groove, as
shown. Be sure they arch upward.
NOTE: You may need to gently
coax some slats into place
depending on how tightly
everything has been assembled.