Insportline Erinome YKB5815 User manual

1
USER MANUAL - EN
IN 7557 Magnetic Upright Bike inSPORTline Erinome (YK-
B5815)

2
CONTENTS
SAFETY INSTRUCTIONS.................................................................................................................................... 3
PARTS LIST........................................................................................................................................................... 4
HARDWARE PACKING LIST ............................................................................................................................. 6
EXPLODED VIEW ................................................................................................................................................ 7
ASSEMBLY INSTRUCTIONS.............................................................................................................................. 8
INSTRUCTION MANUAL FOR TZ-6139.......................................................................................................... 12
MAINTENANCE ................................................................................................................................................. 15
TROUBLESHOOTING........................................................................................................................................ 16
WARM UP AND COOL DOWN ROUTINE ...................................................................................................... 16
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 19

3
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without
notice.
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety instructions when using this
equipment: Read all instructions before using this equipment.
1. Read all the instructions in this manual and do warm up exercises before using this equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every position of the body is
necessary. Refer to Warm Up and Cool Down Routine pages. After exercise, relaxation of the body is
suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This equipment should be placed
on a flat surface when using. Using a mat or other covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that might catch
any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any
problems arise, discontinue use and consult an Authorized Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is designed for adults
only. The minimum free space required for safe operation is not less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately
and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your physician. This is especially important
for the persons who are over 35 years old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
CAUTION: Read all instructions carefully before operating this product. Retain this Owner’s Manual for
future reference.

4
PARTS LIST
No.
Description
Qty
001
Main Frame
1
002
Front Stabilizer
1
003
Rear Stabilizer
1
004
Idle Wheel Bracket
1
005
Seat Post
1
006
Seat Sliding Tube
1
007
Handlebar Post
1
008
Handlebar
1
009
U Bracket
2
010
Washer Ø16xØ8x1.5
5
011
Eyebolt M8x85
1
012
End Cap For Front Stabilizer
2
013
End Cap For Rear Stabilizer
2
014
Big Curve Washer Ø8
8
015
Adjustable Leveler M8
1
016
Spring Ø6
2
017
Bolt M8x70
4
018
Seat Sliding Tube End Cap (□38)
2
019
Bolt M8x15
4
020
Bolt M8x20
1
021
Eyebolt M6x36
2
022
Idle Wheel Ø10xØ35
1
023
Screw ST2.9×12
2
024
Screw ST4.2×20
6
025
Screw ST4.2×25
7
026
Pan Head Phillips Self Drilling Screw ST4.2x20
4
027
Nylon Nut M8
6
028
Nut M6
2
029
Hexagon Nut M10
2
030
Cap Nut M8
4
031
Flywheel Ø230x40xØ32
1
032
Bearing Cup
2
033
Bearing 6000ZZ
2
034
Bearing Nut I 15/16"
1
035
Bearing Nut II 7/8"
1

5
036
Washer Ø24xØ40x3.0
1
037
Washer Ø23xØ34.5x2.5
1
038
Hexagon Nut 7/8"
1
039
Belt Pulley with Crank Ø240J6
1
040
AC Adapter
1
041
Power supply wire
1
042
Bolt M5X10
4
043
Handlebar Foam Grip Ø24xØ30x490
2
044
Left Pedal YH-30X
1
045
Right Pedal YH-30X
1
046
End Cap for Handlebar
2
047
Cover Cap
2
048
Round Knob M16
1
049
Hand Pulse Sensor with Wire L=750mm
2
050
Sensor with Wire L=750mm
1
051
Left Chain Cover
1
052
Right Chain Cover
1
053
Seat Post Bushing
1
054
Motor
1
055
Motor Tension Cable L=500mm
1
056
Clamp Cover
1
057
Spacer (Ø12x20x1.5)
1
058
Handlebar Post Cover
1
059
Seat Post Cover
1
060
Belt PJ360 J6
1
061
Seat Cushion DD-982AT
1
062
Computer
1
063
Extension Sensor Wire (L=1000mm)
1
064
Handlebar T-Knob (M8x55)
1
065
Washer Ø12x Ø6x1.0
1
066
Bolt M6X10
1
067
Wire End Cap
1
068
Washer Ø8x Ø20x2.0
1
069
Sensor Wire L=600mm
1

6
HARDWARE PACKING LIST
(17) Bolt M8x70
4 PCS
(14) Big Curve Washer Ø8
4 PCS
(30) Cap Nut M8
4 PCS
TOOLS
Allen Wrench S6
1 PC
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
1 PC

7
EXPLODED VIEW

8
ASSEMBLY INSTRUCTIONS
STEP 1: FRONT AND REAR STABILIZERS INSTALLATION
Position the Front Stabilizer (2) in front of the Main Frame (1) and align bolt holes. Attach the Front Stabilizer
(2) onto the front curve of the Main Frame (1) with two M8x70 Bolts (17), two Ø8 Big Curve Washers (14), and
two M8 Cap Nuts (30).
Position the Rear Stabilizer (3) behind the Main Frame (1) and align bolt holes. Attach the Rear Stabilizer (3)
onto the rear curve of the Main Frame (1) with two M8x70 Bolts (17), two Ø8 Big Curve Washers (14), and two
M8 Cap Nuts (30).
Foot Pedals Installation:
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and “L” for Left.
Insert the pedal shaft of Left Foot Pedal (44) into threaded hole in the left Crank (39). Turn the pedal shaft by
hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the threads.
Screwdriver provided Insert pedal shaft of Right Foot Pedal (45) into threaded hole in right Crank (39). Turn the
pedal shaft by hand in the clockwise direction until snug.

9
STEP 2: SEAT POST, SEAT POST COVER, SEAT CUSHION, AND SEAT SLIDING TUBE
INSTALLATION
Slide the Seat Post Cover (59) onto the tube of the Main Frame (1). Insert the Seat Post (5) into the Seat Post
Bushing (53) on the tube of the Main Frame (1) and then attach the Seat Post Knob (48) onto the tube of the
Main Frame (1) by turning it in a clockwise direction with Multi Hex Tool provided to lock the Seat Post (5) in
the suitable position.
Remove three M8 Nylon Nuts (27) and three Ø16xØ8x1.5 Washers (10) from underside of the Seat Cushion
(61). Remove nylon nuts and washers with the Multi Hex Tool with Phillips Screwdriver provided. Guide bolts
on underside of the Seat Cushion (61) through holes on top of the Seat Sliding Tube (6), attach with three
removed M8 Nylon Nuts (27) and Ø16xØ8x1.5 Washers (10). Tighten nylon nuts and washers with the Multi
Hex Tool with Phillips Screwdriver provided.
Guide the Seat Sliding Tube Bolt on underside of the Seat Sliding Tube (6) through hole on top of the Seat Post
(5), attach with one Ø16xØ8x1.5 Washer (10) and Seat Adjustment Knob (15).

10
STEP 3: HANDLEBAR POST, HANDLEBAR POST COVER
Remove four M8x15 Bolts (19), four Ø20xØ8x2.0 Washers (14) from the Main Frame (1). Remove bolts with
the S6 Allen Wrench provided.
Slide the Handlebar Post Cover (58) up to the Handlebar Post (7).
Connect the Sensor Wire (69) from the Main Frame (1) to the Extension Sensor Wire (63) from the Handlebar
Post (7).
Insert the Handlebar Post (7) onto the tube of the Main Frame (1) and secure with four M8x15 Bolts (19), four
Ø20xØ8x2.0 Washers (14) that were removed. Tighten bolts with the S6 Allen Wrench provided.
Slide the Handlebar Post Cover (58) down to the Handlebar Post (7).