Insportline IN 8245 Nahary User manual

USER MANUAL – EN
IN 8245 Recumbent inSPORTline Nahary
1

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS.............................................................................................................3
OVERVIEW DRAWING.........................................................................................................................................4
PARTS LIST.............................................................................................................................................................5
HARDWARE PACKING LIST...........................................................................................................................7
TOOLS..................................................................................................................................................................8
ASSEMBLY INSTRUCTIONS................................................................................................................................8
STEP 1: REAR MAIN FRAME INSTALLATION.............................................................................................8
STEP : FRONT AND REAR STABILIZERS INSTALLATION......................................................................9
STEP 3: RIGHT/LEFT FOOT PEDALS AND BACK/SEAT SUPPORT BRACKET INSTALLATION.......10
STEP 4: FRONT POST AND FRONT POST COVER INSTALLATION.......................................................11
STEP 5: SEAT/BACK CUSHIONS AND REAR HANDLEBAR INSTALLATION......................................1
STEP 6: FRONT HANDLEBAR, FRONT/REAR DECORATIVE COVERS FOR FRONT POST, AND
COMPUTER INSTALLATION.........................................................................................................................13
OPERATING THE COMPUTER...........................................................................................................................14
ADJUSTMENTS....................................................................................................................................................15
ADJUSTING THE ADJUSTABLE LEVELER.................................................................................................15
ADJUSTING THE FRONT HANDLEBAR......................................................................................................15
ADJUSTING THE TENSION CONTROL KNOB............................................................................................16
ADJUSTING THE SEAT FORWARD OR BACK...........................................................................................16
MAINTENANCE...................................................................................................................................................16
CLEANING........................................................................................................................................................16
STORAGE..........................................................................................................................................................16
TROUBLESHOOTING..........................................................................................................................................17
WARM UP AND COOL DOWN ROUTINE........................................................................................................17
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS.........................................................19

IMPORTANT Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without
notice.
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important safety instructions when
using this equipment. Read all instructions before using this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the equipment is
properly assembled and tightened before use.
. Before exercise, in order to avoid injuring the muscle, warm-up exercises are recommended.
3. Please make sure all parts are not damaged and fixed well before use. This equipment should be placed
on a flat surface when using. Using a mat or other covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that may catch
any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any
problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising
immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away from the
equipment while in use. This machine is designed for adults use only. The minimum free space required
for safe operation is not less than two meters.
1 . The maximum weight capacity for this product is 140 kgs.
WARNING Before beginning any exercise program consult your physician. This is especially important
for the people who are over 35 years old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
CAUTION Read all instructions carefully before operating this product. Retain this Owner’s Manual for
future reference.
3

OVERVIEW DRAWING
4

PARTS LIST
No. Description Qty
001 Computer (XLG-903) 1
00 Extension Sensor Wire B L=500mm 1
003 Extension Hand Pulse Sensor Wire D L=500mm
004 Screw ST4. x 0mm 5
005 Front Handlebar Foam Grip Ø33xØ 7x500
006 Wire Plug Ø1 .1 3
007 Front Handlebar Ø 5x1.5 1
008 Front Decorative Cover for Front Post 1
009 Screw ST .9x16mm 8
010 Extension Hand Pulse Sensor Wire C L=350mm 1
011 Bolt M5x30 1
01 Big Curve Washer Ø5 1
013 Front Post Ø76x1.5 1
014 Tension Control Knob L=170mm 1
015 Front Handlebar T-Knob M8x75 1
016 Spacer Ø1 x1.5x50 1
017 Rear Decorative Cover for Front Post 1
018 Bolt M8x15mm 16
019 Curve Washer Ø8 4
0 0 Front Post Cover 1
0 1 Front Left Stabilizer End Cap 1
0 Nylon Nut M6
0 3 Transport Wheel Ø45x19
0 4 Bolt M6x40
0 5 Bolt M8x90mm
0 6 Front Stabilizer Ø76x1.5 1
0 7 Front Right Stabilizer End Cap 1
0 8 Front Main Frame 80x40x 1
0 9 Left Foot Pedal (YH-30X) 1
030 Cover Cap Ø40xØ 5x10
031 Screw ST4. x 5mm 11
03 Phillips Self Tapping Screw ST4. x 5mm 4
033 Left Shroud 1
034 Hexagon Nut 7/8" 1
035 Washer Ø34.5xØ 3x .5 1
5

036 Bearing Nut II 7/8" 1
037 Bearing
038 Bearing Cup
039 Screw ST .9x1 mm
040 Sensor with Wire L=750mm 1
041 Bearing Nut I 15/16" 1
04 Washer Ø40xØ 4x3 1
043 Belt Pulley with Crank Ø 60 J6 1
044 Belt PJ390 J6 1
045 Right Shroud 1
046 Right Foot Pedal (YH-30X) 1
047 Nut M10x1.0
048 Eyebolt M6x36
049 Tension Bracket
050 Spring Washer Ø6
051 Nut M6
05 Flywheel Ø 50 1
053 Washer Ø16xØ8x1.5t 18
054 Nylon Nut M8
055 Idle Wheel 1
056 Idle Wheel Bracket 1
057 Bolt M8x 0mm 1
058 Spring Ø18x9 xØ3 1
059 Screw ST4.8x 0mm
060 Left Rear Main Frame Cover 1
061 Hand Pulse Sensor Extension Wire A L=1000mm 1
06 Rear Stabilizer End Cap
063 Adjustable Leveler M10
064 Carriage Bolt M8x90mm
065 Nut M10
066 Rear Stabilizer Ø76x1.5 1
067 Rear Main Frame 80x40x1.5 1
068 Big Curve Washer Ø 0xØ8x1.5t 6
069 Cap Nut M8 4
070 Right Rear Main Frame Cover 1
071 Round Knob M16x1.5 1
07 Bushing
073 Triangle Knob M1 x58 1
074 Rear Handlebar Round End Cap
6

075 Hand Pulse Sensor with Wire L=750mm
076 Rear Handlebar Foam Grip Ø 7xØ33x600
077 Bolt M8x45mm
078 Rear Handlebar Ø76x1.5 1
079 Seat Sliding Tube 53x 3x 1
080 Bolt M6x15 8
081 Seat Cushion 4 0x 50x60 1
08 Back and Seat Support Bracket 53x 3x 1
083 Backrest and Seat Support Bracket End Cap 1
084 Back Cushion x400x430x90 1
085 Bolt M8x30mm
086 Tension Cable L=950mm 1
087 Washer Ø6xØ18 8
088 Extension Hand Pulse Sensor Wire B L=1000mm 1
089 Extension Sensor Wire A L=350mm 1
HARDWARE PACKING LIST
(4) Screw ST4. x 0mm
3 PCS
(9) Screw ST .9x16mm
8 PCS
( 5) Bolt M8x90mm
PCS
(53) Washer Ø16xØ8x1.5t
PCS (64) Carriage Bolt M8x90mm
PCS
(68) Big Curve Washer
Ø 0xØ8x1.5t
6 PCS
(69) Cap Nut M8
4 PCS
(77) Bolt M8x45mm
PCS
7

TOOLS
Allen Wrench S6
1 PC Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
1 PC
ASSEMBLY INSTRUCTIONS
STEP 1 REAR MAIN FRAME INSTALLATION
Tools
Allen Wrench
Remove two M8x30mm Bolts (85), four M8x15mm Bolts (18), and six Ø16xØ8x1.5t Washers (53) from the
Rear Main Frame (67). Remove bolts with the S6 Allen Wrench provided.
Connect the Hand Pulse Sensor Extension Wire A (61) from the Rear Main Frame (67) to the Hand Pulse Sensor
Extension Wire B (88) from the Front Main Frame ( 8).
Attach the Rear Main Frame (67) into the Front Main Frame ( 8) with two M8x30mm Bolts (85), four
M8x15mm Bolts (18), and six Ø16xØ8x1.5t Washers (53) that were removed. Tighten bolts with the S6 Allen
Wrench provided.
8

STEP 2 FRONT AND REAR STABILIZERS INSTALLATION
Tools
Multi Hex Tool with Phillips Screwdriver
Allen Wrench
Hardware
( 5) Bolt M8x90mm
PCS
(68) Big Curve Washer
Ø 0xØ8x1.5t
4 PCS
(64) Carriage Bolt
M8x90mm
PCS
(69) Cap Nut M8
PCS
Position the Front Stabilizer ( 6) in front of Front Main Frame ( 8) and align bolt holes.
Attach the Front Stabilizer ( 6) onto the front curve of the Front Main Frame ( 8) with two M8x90mm Bolts
( 5) and two Ø 0xØ8x1.5t Big Curve Washers (68). Tighten bolts and curve washers with the S6 Allen Wrench
provided.
Position the Rear Stabilizer (66) behind the Rear Main Frame (67) and align bolt holes.
Attach the Rear Stabilizer (66) onto the rear curve of the Rear Main Frame (67) with two M8x90mm Carriage
Bolts (64), two Ø 0xØ8x1.5t Big Curve Washers (68), and two M8 Cap Nuts (69). Tighten cap nuts and bolts
with the Multi hex Tool with Phillips Screwdriver provided.
Install two M10 Adjustable Levelers (63) with two M10 Nuts (65) onto the Rear Stabilizer (66).
9

STEP 3 RIGHT/LEFT FOOT PEDALS AND BACK/SEAT SUPPORT BRACKET
INSTALLATION
Tools
Multi Hex Tool with Phillips Screwdriver
Allen Wrench S6
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and “L” for Left.
Insert the pedal shaft of Left Foot Pedal ( 9) into threaded hole in the left Crank (43). Turn the pedal shaft by
hand in the counter-clockwise direction until snug.
Note DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the threads.
Tighten the pedal shaft of Left Foot Pedal ( 9) with the Multi Hex Tool with Phillips Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (46) into threaded hole in right Crank (43). Turn the pedal shaft by hand in
the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (43) with the Multi Hex Tool with Phillips Screwdriver provided.
Remove eight M8x15mm Bolts (18), eight Ø16xØ8x1.5t Washers (53), and the Seat Sliding Tube (79) from the
Back and Seat Support Bracket (8 ). Remove bolts with the S6 Allen Wrench provided.
Insert the Seat Sliding Tube (79) into the Bushings (7 ) of the Rear Main Frame (67).
Attach the Seat Sliding Tube (79) to the Back and Seat Support Bracket (8 ) with eight M8x15mm Bolts (18)
and eight Ø16xØ8x1.5t Washers (53) that were removed. Tighten bolts with the S6 Allen Wrench provided.
Adjust the seat position and insert the Round Knob (71) and Triangle Knob (73). Turn the
Round Knob (71) and Triangle Knob (73) in the clockwise direction to tighten.
10