Insportline IN 9360 Airin User manual

1
USER MANUAL – EN
IN 9360 Spinning Bike inSPORTline Airin

2
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS............................................................................................................ 3
ASSEMBLY ........................................................................................................................................................... 4
HOW TO ADJUST THE RESISTANCE............................................................................................................. 10
HOW TO STOP THE BIKE IMMEDIATELY.................................................................................................... 10
PARTS LIST......................................................................................................................................................... 10
EXPLODED VIEW.............................................................................................................................................. 13
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 14

3
IMPORTANT SAFETY INSTRUCTIONS
WARNING! To reduce the risk of serious injury, read the following important precautions before using the Spin
Bike.
•Read all instructions and warnings in this manual before using the Spin bike.
•Before using this spin bike, please consult your physician for a complete physical examination. If you
feel any discomfort while exercising, please stop immediately and consult your doctor.
•Keep the Spin bike indoors, away from moisture and dust. Place the Spin bike on a level surface, with a
mat beneath it to protect the floor or carpet. Make sure that there is enough clearance around the Spin
bike to mount, dismount, and use it.
•Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
•Ensure that your fingers or clothing do not catch in the Spin bike moving parts.
•Please keep children and pets away from the Spin bike at all times. It is only suitable for adults.
•The Spin bike should not be used by persons weighting more than 150 kg. Serious injury may occur if
the user’s weight exceeds the limit shown here.
•To prevent injuring you when lifting and moving the machine, Please getting someone to help you.
•If you hear unusual noise when exercising, please stop your training immediately. Do not use the Spin
bike until the problem has been resolved.
•To prevent injuring you when stop exercising, do not touch the flywheel immediately.

4
ASSEMBLY
Assembly requires two persons. Place all parts of the Spin bike in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
For your convenience, we have identified the hardware used in the assembly of this product. This chart is
provided to help you identify those items that may be unfamiliar to you.
NOTE: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it
has been preassembled.
No. Description Qty
22 L-knob M10x20mm 1
23 Knob M10x28mm 1
24 Lock nut M10 1
25 Washer 19.5x38x2T 1
35 Cap nut M10 4
36 Carriage bolt M10x55mm 4
37 Washer 10x19x1.5T 4
46 Washer 10x29x2T 2
A Spanner (13, 15) 1
B Spanner (14, 17) 1
C Multi wrench (13, 14, 15) 1

5
STEP 1: Front / Rear Stabilizers Installation
Hardware:
(36) Carriage bolt, 4 PCS (35) Cap nut, 4 PCS (37) Washer, 4 PCS
Tool:
While another person lifts the front of Frame (1), attach the Front stabilizer (2) to the Frame with two
M10x55mm Carriage bolts (36) from the above Stabilizer, and fix it with two 10x19x1.5mm Washers (37) &
two M10 Cap nuts (35).
Do the same to the Rear Stabilizer (3).

6
STEP 2: Handlebar Installation
Hardware:
(23) Knob M10x28mm, 1
PC (24) Lock nut M10, 1 PC (25) Washer 19.5x38x2mm, 1 PC (46) Washer 10x29x2mm, 1 PC
Release the Spring knob (21), then insert the Upright post (4) into the Frame (1). There are 5 holes on the
Upright post (4), please select the desired position and tighten the Spring knob (21). Next connect the Handlebar
(6) with the Upright post (4), select the desired position and fix it with one M10x28mm Knob (23), one
10x29x2mm Washer (46), one 19.5x38x2mm Washer (25) and M10 Lock nut (24).

7
STEP 3: Seat Post / Seat Installation
Hardware:
(22) L-knob M10, 1 PC (46) Washer 10x29x2mm, 1 PC
Tool:
Release the Spring knob (21), then insert the Seat post (5) into the Frame (1). There are 9 holes on the Seat post
(5), please select the desired position and tighten the Spring knob (21). Next attach the Seat (9) to the Moving
bracket (7), then connect the Moving bracket (7) with the Seat post (5), select the desired position and fix it with
one M10 L-knob (22) & one 10x29x2 mm Washer (46).

8
STEP 4: R / L Pedals Installation
Tool:
Screw R/L pedals (20) onto crank (18). The pedals are marked with R and L at the screw. Tighten the left pedal
counter-clockwise, the right pedal clockwise.

9
STEP 5: Bottle Holder Installation
Tool:
Release two M5x15mm Bolts (78) from the Frame (1), then put the Bottle holder (48) onto the Frame (1) and re-
lock two Bolts (78).

10
HOW TO ADJUST THE RESISTANCE
Clockwise rotate the knob to increase the resistance, and counter-clockwise rotate the knob to decrease the
resistance as below images.
HOW TO STOP THE BIKE IMMEDIATELY
When you want to stop the bike in training, please push down the knob as below image.
PARTS LIST
No. Description Qty Unit
1 Main Frame 1 pc
2 Front stabilizer bar 40x80x2T 1 pc
3 Rear stabilizer bar 40x80x2T 1 pc
4 Upright post 40x80x2T 1 pc
5 Seat post 40x80x2T 1 pc
6 Handlebar Φ25.4x2T 1 pc
7 Moving bracket 1 pc
8 Plastic fastener 50x100x100mm 2 pc
9 Seat VL-6100 1 pc
10 Flywheel Φ468 1 pc