Insportline IN 9361 Baraton User manual

1
USER MANUAL –EN
IN 9361 Spinning Bike inSPORTline Baraton

2
CONTENTS
IMPORTANT SAFETY INFORMATION............................................................................................................. 3
EXPLODED VIEW (A).......................................................................................................................................... 4
EXPLODED VIEW (B).......................................................................................................................................... 5
PARTS LIST........................................................................................................................................................... 6
ASSEMBLING INSTRUCTIONS ......................................................................................................................... 8
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 10

3
IMPORTANT SAFETY INFORMATION
Please keep this manual in a safe place for reference.
1. It is important to read this entire manual before assembling and using the equipment. Safe and efficient use
can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to
ensure that all users of the equipment are informed of all warnings and precautions.
2. Before starting any exercise program you should consult your doctor to determine if you have any physical or
health conditions that could create a risk to your health and safety, or prevent you from using the equipment
properly. Your doctor's advice is essential if you are taking medication that affects your heart rate, blood
pressure or cholesterol level.
3. Be aware of your body's signals. Incorrect or excessive exercise can damage your health. Stop exercising if
you experience any of the following symptoms: Pain, tightness in your chest, irregular heartbeat, extreme
shortness of breath, feeling light headed, dizzy or nauseous. If you do experience any of these conditions you
should consult your doctor before continuing with your exercise program.
4. Keep children and pets away from the equipment. The equipment is designed for adult use only.
5. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. For safety
space, the equipment should have at least 0.6 meter of free space all around it.
6. Before using the equipment, check the handlebar, seat, pedals, and the nuts and bolts are securely tightened.
7. The safety level of the equipment can only be maintained if it is regularly examined for damage and/or wear
and tear. (E.g. handle bar, pedals, and seat…..)
8. Always use the equipment as indicated. If you find any defective components while assembling or checking
the equipment, or if you hear any unusual noises coming from the equipment during use, stop immediately.
Do not use the equipment until the problem has been rectified.
9. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may get caught in the
equipment or that may restrict or prevent movement.
10.The equipment has been tested and certified to EN957 under class HC, suitable for domestic, home use only.
Maximum weight of user: 120kg. Braking is speed independent.
11.The equipment is not suitable for therapeutic use.
12.Care must be taken when lifting or moving the equipment so as not to injure your back. Always use proper
lifting techniques and/or seek assistance if necessary.
13.All moveable accessories (e.g. pedal, handlebar, saddle....etc.) require weekly maintenance. Check them
before use every time. If anything broken or loose, please fix them immediately. You may continue using
bike after they return to good conditions.

4
EXPLODED VIEW (A)

5
EXPLODED VIEW (B)

6
PARTS LIST
NO.
NAME
SPECIFICATION
QTY
1
Main frame
1
2
Seat post
30*70*1.5T*438L
1
3
Seat sliding post
■30*30*2.0T*320L
1
4
Handlebar post
30*70*1.5T*260L
1
5
Handlebar
●φ25*2T
1
6
Front stabilizer
40*80*1.5T*500L
1
7
Rear stabilizer
40*80*1.5T*500L
1
8
Adjusting knob
M16*1.5
3
9
Sleeve
Suit 38*38*1.5T* INNER
30*30
2
10
Bushing
Suit 30*30*1.5T tube
1
11
Saddle
1
12
Small sprocket wheel
φ65.13*16 gear
1
13
Locking ring
φ42*5.0
1
14
Axis spacer
ф26*ф20.2*6T
1
15
Bolt
M8*16L
2
16
Washer
Φ8
8
17
Transportation wheel
2
18
Handlebar decorating cover
1
19
Screw
M4*10L
2
20
Screw
M3*16L
2
21
Wire protector
Φ13
1
22
Sleeve
Outer 40*80*1.5T*
inner30*70
2
23
Braking knob
M8
1
24
Braking rod
M10*P1.5*265L
1
25
Compression spring
φ12.4*φ1.4*27L
1
26
M10 compression nut
M10*P1.5*16*16*15L
1
27
Nut
M8
5
28
Domed nut
M8
5
29
Front decorating cover
ABS
1
30
Screw
ST4.2*16
8
31
Frame decoration cover
ABS
1
32
Screw
ST4.2*16 headφ8
7
33
Rob pad
44*25*3
1
34
Spring steel
1.2
1

7
35
Flat washer
2
36
Outer cover
1
37
Bolt
M5*15
2
38
Brake blockbuster
34.5*23.5*2.0
1
39
Brake spacer
34*24*3
3
40
Brake bracket
ABS
1
41
Felt wool
108*28*6
1
42
Screw
M5*30
2
43
Nylon nut
M5
2
44
Bottle holder
1
45
Screw
M5*15L
2
46
Nut
M12*P1.25
2
47
Washer
ф35*ф12.5*2.0
2
48
Short step tube
φ20*φ12.2*22L
1
49
Flywheel axis
φ15*146*M12*P1.25
1
50
Bearing
6001RS
2
51
Flywheel
φ450*35W
1
52
Long step tube
φ20*φ12.2*25L
1
53
Nut
M6
2
54
Bolt
M6*50
2
55
Crank cover
2
56
Flange nut
M10*P1.25*8T
2
57
Left crank
165L
1
58
Left pedal
1
59
Circlip
φ20
1
60
Bearing
6004
2
61
Sprocket wheel with Axis
52T
1
62
Inner cover
1
63
Chain
d=7.11 p=12.7 112PCS
1
64
Nylon nut
M8
2
65
Right crank
165L
1
66
Right pedal
1
67
Tube plug
OVAL 40*80*1.5T
4
68
Adjusting pad
M8
4
69
Bolt
M8*52 S=20
4
70
Bolt
M8*42L S=20
2

8
TOOLS
SPANNER:
ASSEMBLING INSTRUCTIONS
STEP 1:
Attach the rear stabilizer (pt. 7) to the main frame (pt. 1) using two sets
of domed nuts (pt. 28), washers (pt. 16) and bolts (pt. 69) and tighten.
STEP 2:
Attach the front stabilizer (pt. 6) to the main frame (pt. 1) using two
sets of domed nuts (pt. 28), washers (pt. 16) and bolts (pt. 69) and
tighten.
STEP 3:
The pedals (pt. 58, 66) are marked "L" and "R" –Left and Right.
Connect them to their appropriate crank arms with the spanner tool and
tighten. The right crank arm is on the right-hand side of the cycle as
you sit on it.
NOTE: The right pedal should be threaded on clockwise and the left
pedal anticlockwise.

9
STEP 4:
Slacken the adjusting knob (pt. 8) and pull back and locate the
handlebar post (pt. 4) in the housing on the main frame (pt. 1). Align
the correct holes at the desired height until the “stop” mark and then
tighten the adjusting knob (pt. 8).
STEP 5:
Attach handlebar (pt. 5) to handlebar post (pt. 4) using two sets of
washers (pt. 16) and bolts (pt. 15) and tighten.
STEP 6:
Fix the upper part of handlebar decoration cover (pt. 18) using screws
(pt. 20).
STEP 7:
Slacken the knurled section of the round knob (pt. 8) and pull the knob
back, slide the seat post (pt. 2) into the seat post housing on the main
frame (pt. 1). Then select and align holes for the desired height.
Release the knob and retighten the knurled portion.

10
STEP 8:
Fix the seat (pt. 11) to the seat sliding post (pt. 3) as shown, and
tighten the bolts around the screws under the seat. You will have to
loosen the knurled section of the adjustment knob (pt. 8) and pull the
knob back before sliding the sliding seat post (pt. 3) into the seat post
(pt. 2) and then select and align holes for the desired distance and
tighten the knob.
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS
General Conditions of Warranty and Definition of Terms
All Warranty Conditions stated hereunder determine Warranty Coverage and Warranty Claim Procedure.
Conditions of Warranty and Warranty Claims are governed by Act No. 40/1964 Coll. Civil Code, Act No.
513/1991 Coll., Commercial Code, and Act No. 634/1992 Coll., Consumer Protection Act, as amended, also in
cases that are not specified by these Warranty rules.
The seller is SEVEN SPORT s.r.o. with its registered office in Borivojova Street 35/878, Prague 13000,
Company Registration Number: 26847264, registered in the Trade Register at Regional Court in Prague, Section
C, Insert No. 116888.
According to valid legal regulations it depends whether the Buyer is the End Customer or not.
“The Buyer who is the End Customer” or simply the “End Customer” is the legal entity that does not conclude
and execute the Contract in order to run or promote his own trade or business activities.
“The Buyer who is not the End Customer” is a Businessman that buys Goods or uses services for the purpose of
using the Goods or services for his own business activities. The Buyer conforms to the General Purchase
Agreement and business conditions to the extent specified in the Commercial Code.
These Conditions of Warranty and Warranty Claims are an integral part of every Purchase Agreement made
between the Seller and the Buyer. All Warranty Conditions are valid and binding, unless otherwise specified in
the Purchase Agreement, in the Amendment to this Contract or in another written agreement.
Warranty Conditions
Warranty Period
The Seller provides the Buyer a 24 months Warranty for Goods Quality, unless otherwise specified in the
Certificate of Warranty, Invoice, Bill of Delivery or other documents related to the Goods. The legal warranty
period provided to the Consumer is not affected.
By the Warranty for Goods Quality, the Seller guarantees that the delivered Goods shall be, for a certain period
of time, suitable for regular or contracted use, and that the Goods shall maintain its regular or contracted
features.
The Warranty does not cover defects resulting from:
User’s fault, i.e. product damage caused by unqualified repair work, improper assembly, insufficient insertion of
seat post into frame, insufficient tightening of pedals and cranks
Improper maintenance
Mechanical damages
Regular use (e.g. wearing out of rubber and plastic parts, joints etc.)
Unavoidable event, natural disaster
Adjustments made by unqualified person

11
Improper maintenance, improper placement, damages caused by low or high temperature, water, inappropriate
pressure, shocks, intentional changes in design or construction etc.
Warranty Claim Procedure
The Buyer is obliged to check the Goods delivered by the Seller immediately after taking the responsibility for
the Goods and its damages, i.e. immediately after its delivery. The Buyer must check the Goods so that he
discovers all the defects that can be discovered by such check.
When making a Warranty Claim the Buyer is obliged, on request of the Seller, to prove the purchase and validity
of the claim by the Invoice or Bill of Delivery that includes the product’s serial number, or eventually by the
documents without the serial number. If the Buyer does not prove the validity of the Warranty Claim by these
documents, the Seller has the right to reject the Warranty Claim.
If the Buyer gives notice of a defect that is not covered by the Warranty (e.g. in the case that the Warranty
Conditions were not fulfilled or in the case of reporting the defect by mistake etc.), the Seller is eligible to
require a compensation for all the costs arising from the repair. The cost shall be calculated according to the
valid price list of services and transport costs.
If the Seller finds out (by testing) that the product is not damaged, the Warranty Claim is not accepted. The
Seller reserves the right to claim a compensation for costs arising from the false Warranty Claim.
In case the Buyer makes a claim about the Goods that is legally covered by the Warranty provided by the Seller,
the Seller shall fix the reported defects by means of repair or by the exchange of the damaged part or product for
a new one. Based on the agreement of the Buyer, the Seller has the right to exchange the defected Goods for a
fully compatible Goods of the same or better technical characteristics. The Seller is entitled to choose the form of
the Warranty Claim Procedures described in this paragraph.
The Seller shall settle the Warranty Claim within 30 days after the delivery of the defective Goods, unless a
longer period has been agreed upon. The day when the repaired or exchanged Goods is handed over to the Buyer
is considered to be the day of the Warranty Claim settlement. When the Seller is not able to settle the Warranty
Claim within the agreed period due to the specific nature of the Goods defect, he and the Buyer shall make an
agreement about an alternative solution. In case such agreement is not made, the Seller is obliged to provide the
Buyer with a financial compensation in the form of a refund.

12
Date of Sale: Stamp and Signature of Seller: