Insportline inCondi UB35i II User manual

1
USER MANUAL – EN
IN 16505 Exercise Bike inSPORTline inCondi UB 5i II

2
CONTENTS
SAFETY INSTRUCTIONS ....................................................................................................................... 3
EXPLODED VIEW – ASSEMBLY DRAWING ......................................................................................... 4
PARTS LIST ............................................................................................................................................ 5
HARDWARE & TOOL ..........................................................................................................................
ASSEMBLY ............................................................................................................................................. 8
EXERCISE COMPUTER INSTRUCTIONS ........................................................................................... 13
EXERCISE INSTRUCTIONS ................................................................................................................ 19
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ................................................. 20

3
SAFETY INSTRUCTIONS
This exerciser is made for home use only, and tested up to a max body weight of 150 kg.
1. Follow the steps of the assembly instructions carefully.
2. Use only original parts as delivered.
3. Place this exerciser on an even, non-slippery surface. Because of possible corrosion, the
usage of any exerciser in moist areas is not recommended.
4. Before assembly, check if delivery is complete by using the included parts-list.
5. For assembly use only suitable tools and ask for assistance with assembly if necessary.
6. Check before the first training and every 1-2 month that all connecting elements are tight fitting
and are in the correct condition.
. Replace defective components immediately and/or keep it out of use until repair.
8. For repairs, use only original spare parts.
9. In case of repair please ask your dealer for advice.
10. Ensure that training starts only after correct assembly and inspection.
11. For all adjustable parts be aware of the maximum positions to which they can be adjusted/
tightened to.
12. This exerciser is designed for adults. Please ensure that children use the exerciser only under
the supervision of an adult.
13. Ensure that those present are aware of possible hazards, e. g. movable parts during training.
14. Warning: incorrect/excessive training can cause health injuries.
15. Please follow the advice for correct training as detailed in training instructions.
16. Consult your physician before starting with any exercise program. They can advise on the kind
of training and which impact is suitable.
1 . This user manual is only for customers’ reference.
18. The supplier cannot guarantee for mistakes occurring due to translation or change in technical
specification of the product.
19. All data displayed are approximate guidance and cannot be used in any medical application.
20. For your own safety, always ensure that there is at least 0.6 meter of free space in all
directions around your product while you are exercising.
21. WARNING! A hart rate monitor may not be accurate. Overloading during training may cause
serious injury or death. If you feel any discomfort, immediately stop the exercise!
22. Category: Class HA (according to EN ISO 2095 ) for home use.
23. Max user weight: 150 kg

4
EXPLODED VIEW – ASSEMBLY DRAWING

5
PARTS LIST
NO. Description Q'ty
A,A-1 Console and screw 1 SET
B-1 Hex. screw M8xP1.25x12Lx5t 3 PCS
B-2 Big Pulley 1 PCS
B-3 Bushing 1 PCS
B-4 Shaft 1 PCS
C-1,C-3~C-13 Flywheel set 1 SET
C-2 Nut 3/8"-26x4.5t 5 PCS
D-1~D-4,D- ~D9 Idler wheel set 1 SET
D-5 Hex. bolt M8xP1.25x20L 1 PCS
D-6 Flat washer φ8.5xφ25x1t 1 PCS
E-1 Flat washer φ8*φ19*2T 2 PCS
E-2 Allen bolt M8*P1.25*16L 4 PCS
E-3 Semi-circle washer Φ8xφ19x2t 2 PCS
F Magnetic set 1 PCS
F-1 Hex. screw M6xP1.0*16L 2 PCS
F-2 Spring washer φ6 2 PCS
F-3 Flat washer φ6xφ13x1t 2 PCS
G-1 Right chain cover 1 PCS
G-2 Crank (Right) 1 PCS
G-3 Nylon screw M8xP1.0x20L 2 PCS
G-4R, G-4L Pedal (R+L) 1/1 PCS
G-5 Screw M4x50L 5 PCS
G-6 Screw M5x16L 6 PCS
G- Chain cover (Left) 1 PCS
G-8 Plastic bushing for main frame 1 PCS
G-9 DC cable 1 PCS
G-10 Main frame 1 PCS
G-11 Seat 1 PCS
G-12 Adaptor 1 PCS
G-13 Bearing 2 PCS
G-14 Wave washerφ1 .5xφ25x0.3t 1 PCS
G-15 Flat washerφ1 .5xφ25x0.3t 1 PCS
G-16 C-type ring 1 PCS
G-1 Belt 1 PCS
G-18 Bottle holder 1 PCS

6
G-19 Adjusting knob for Main frame 1 PCS
G-21 Screw M4x10L 1 PCS
G-22 Sensor box 1 PCS
G-23 Sensor holder 1 PCS
G-24 Cover for handlebar post 1 PCS
G-25 Crank (Left) 1 PCS
H-1 Upper console cable 1 PCS
H-2 Screw M5xP0.8x20L 2 PCS
H-3 Handlebar post 1 PCS
I-1 Stabilizer cap 4 PCS
I-2 Adjustable pad 4 PCS
I-3 Rear stabilizer 1 PCS
J-1 Transport wheel for front stabilizer 2 PCS
J-2 Screw M5x12L 4 PCS
J-3 Front stabilizer 1 PCS
K,G-20 Gear box 1 SET
L-1 Bolt for seat slider 1 PCS
L-2 Cap for seat slider 2 PCS
L-3 Flat washer φ14.3xφ25x2.0t 1 PCS
L-4 Knob for seat slider 1 PCS
L-5 Seat slider 1 PCS
L-6 Seat post 1 PCS
L- Left cover for seat slider 1 PCS
L-8 Right cover for seat slider 1 PCS
L-9 Screw M5x6L 4 PCS
M-1 Foam grip 2 PCS
M-2 Hand pulse 2 PCS
M-3 Cap for foam grip 2 PCS
M-4 Pulse wire 1 PCS
M-5 Screw M4x20L 2 PCS
M-6 Handlebar 1 PCS
N-1~N-4,N-6~N-8 Bolts & nuts pack 1 SET
N-5 Cover for handlebar 1 PCS

HARDWARE & TOOL
ASSEMBLY PARTS IN THE CARTON:

8
ASSEMBLY
STEP 1
1. Fasten front stabilizers (J-3) each with carriage bolts (N-2), flat washers (N-3), nuts (N-1) by
box spanner.
2. Fasten rear stabilizers (I-3) each with carriage bolts (N-2), flat washers (N-3), nuts (N-1) by
box spanner.

9
STEP 2
1. Assemble the straps onto the pedals as the sketches. Adjust the ideal length of the straps
according to your foot size.
2. Assemble the two pedals (G-4R/L) onto the cranks (G-25 & 26) with a screw driver by the
screwdriver / box spanner.
3. Assemble the seat (G-11) to the slider: position the rail onto the seat post (L-6) and tighten
using the washer and horizontal knob (L-4).
4. Insert the seat post (L-6) in the main frame, choose the desired position and tighten the
adjusting knob (G-19). Ensure that the knob is always tightened.
Remarks: When you have chosen a desired position, tighten the Seat Post Knob until you
hear a “click”.

10
STEP
1. Please remove the allen bolt (E-2) and semicircle washers (E-3) and flat washers (E-1) from
the main frame (G-10).
2. Take the handlebar post (H-3) and pass it through the handlebar post cover (G-24).
3. Install the handlebar post (H-3) to the main frame with 2 flat washers (E-1), 2 semicircle
washers (E-3), and 4 allen bolts (E-2).
Remarks: Do not screw one set of the allen screws and semicircle washers too firm at one
time. It is better to fix the four sets firmly at the same time because it helps you to change
angles and to fix easily.