Insportline IN 8056 User manual

1
USER MANUAL - EN
IN 8056 Magnetic Upright Bike inSPORTline Yanti

2
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS............................................................................................................ 3
PARTS LIST........................................................................................................................................................... 4
HARDWARE PACKING LIST.......................................................................................................................... 6
TOOLS................................................................................................................................................................ 6
OVERVIEW DRAWING ....................................................................................................................................... 7
ASSEMBLY INSTRUCTIONS.............................................................................................................................. 8
STEP 1: FRONT/REAR STABILIZERS AND RIGHT/LEFT FOOT PEDALS INSTALLATION................. 8
STEP 2: SEAT POST, SEAT POST BELLOWS, AND SEAT CUSHION INSTALLATION ......................... 9
STEP 3: HANDLEBAR POST INSTALLATION........................................................................................... 10
STEP 4: HANDLEBAR AND COMPUTER INSTALLATION...................................................................... 11
OPERATING THE COMPUTER......................................................................................................................... 12
ADJUSTMENTS.................................................................................................................................................. 13
ADJUSTING THE TENSION CONTROL KNOB.......................................................................................... 13
ADJUSTING THE REAR STABILIZER END CAP....................................................................................... 13
ADJUSTING THE SEAT HEIGHT ................................................................................................................. 13
MAINTENANCE ................................................................................................................................................. 14
CLEANING ...................................................................................................................................................... 14
STORAGE ........................................................................................................................................................ 14
TROUBLESHOOTING........................................................................................................................................ 14
WARM UP AND COOL DOWN ROUTINE ...................................................................................................... 14
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 17

3
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without
notice.
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important safety instructions when
using this equipment. Read all instructions before using this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the equipment is
properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are recommended.
3. Please make sure all parts are not damaged and fixed well before use. This equipment should be placed
on a flat surface when using. Using a mat or other covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that may catch
any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any
problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately
and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away from the
equipment while in use. This machine is designed for adults use only. The minimum free space
required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your physician. This is especially important
for the people who are over 35 years old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
CAUTION: Read all instructions carefully before operating this product. Retain this Owner’s Manual for
future reference.

4
PARTS LIST
No.
Description
Qty
001
Main Frame Ø50x1.5t
1
002
Handlebar Ø25x1.5t
1
003
Handlebar Post L650xØ50
1
004
Rear Stabilizer Ø50x1.5x380mm
1
005
Flywheel Ø230
1
006
Front Stabilizer Ø50x1.5x360mm
1
007
Tension Control Knob L=500
1
008
Seat Post Knob M16x1.5
1
009
Belt 280J4
1
010
Computer
1
011
Wave Washer
1
012
Seat Post Bushing
1
013
Left Cover
1
014
Right Cover
1
015
Cross Recessed Pan Head Tapping Screw ST3x10
2
016
Washer Ø34.5x23x2.5t
1
017
Bearing Nut I 15/16"
1
018
Hexagon Nut 7/8"
1
019
Belt Pulley with Crank 200J6
1
020
Left Foot Pedal JD-12A
1
021
Right Foot Pedal JD-12A
1
022
Bearing Cup
2
023
Ball Bearing
2
024
Hexagon Socket Pan Head Cap Bolt M8x16
6
025
Seat Post 545x20x1.5t
1
026
Sensor with Wire L=550mm
1
027
Seat Cushion DD-98-2AT
1
028
Front Stabilizer End Cap Ø50
2
029
Rear Stabilizer End Cap Ø50
2
030
Small Bearing
2
031
Spring Clip
1
032
Seat Post Bellows
1
033
Extension Sensor Wire L=1100mm
1
034
Cap Nut M10
4
035
Carriage Bolt M10x60
4

5
036
Big Curve Washer Ø10
4
037
Curve Washer Ø18xØ8x1.5t
6
038
Washer Ø18xØ8x1.5t
4
039
Big Spring
1
040
Cross Recessed Pan Head Tapping Screw ST4x16
12
041
Small Spring
1
042
Nylon Nut M8
4
043
Hexagon Bolt M5x30
1
044
Idler Arm
1
045
Bearing 6000-2Z
2
046
Big Washer Ø5xØ20x1.5t
1
047
Cross Recessed Pan Head Bolt M4x12
2
048
Washer Ø24xØ40x3t
1
049
Handlebar End Cap Ø25
2
050
Handlebar Foam Grip Ø30xØ24x455
2
051
Cross Recessed Pan Head Tapping Screw ST4.2x20
2
052
Cross Recessed Pan Head Bolt M6x10
1
053
Hand Pulse Sensor with Wire L=750mm
2
054
Tension Cable L=1150mm
1
055
Washer Ø12xØ6x1.5t
1
056
Washer Ø10.2xØ14x1t
1
057
Cross Recessed Pan Head Bolt M5x45
1
058
Bearing Nut II 13/16"
1
059
Axle
1
060
Cover Cap Ø60xØ27xT7
2
061
Magnet Bracket
1
062
Washer Ø10xØ5.5xT1.5
1
063
Cross Recessed Pan Head Bolt M5x8
1
064
Magnet
3
065
Hexagon Nut M5
2

6
HARDWARE PACKING LIST
(8) Seat Post Knob M16x1.5
1 PC
(34) Cap Nut M10
4 PCS
(35) Carriage Bolt M10x60
4 PCS
(36) Big Curve Washer Ø10
4 PCS
TOOLS
5mm Allen Wrench with Phillips Screwdriver
1 PC
Multi Hex Tool
1 PC

7
OVERVIEW DRAWING

8
ASSEMBLY INSTRUCTIONS
STEP 1: FRONT/REAR STABILIZERS AND RIGHT/LEFT FOOT PEDALS
INSTALLATION
Tool:
Multi Hex Tool
Hardware:
(34) Cap Nut M10
4 PCS
(35) Carriage Bolt M10x60
4 PCS
(36) Big Curve Washer Ø10
4 PCS
STABILIZERS INSTALLATION
Position the Front Stabilizer (6) in front of the Main Frame (1) and align bolt holes. Attach the Front Stabilizer
(6) onto the front curve of the Main Frame (1) with two M10 Cap Nuts (34), two M10x60 Carriage Bolts (35),
and two Ø10 Big Curve Washers (36). Tighten cap nuts with the Multi Hex Tool provided.
Position the Rear Stabilizer (4) behind the Main Frame (1) and align bolt holes. Attach the Rear Stabilizer (4)
onto the rear curve of the Main Frame (1) with two M10 Cap Nuts (34), two M10x60 Carriage Bolts (35), and
two Ø10 Big Curve Washers (36). Tighten cap nuts with the Multi Hex Tool provided.
FOOT PEDALS INSTALLATION
The Pedal Shafts and Pedals are marked “R” for Right and “L” for Left.
Insert the pedal shaft of Left Foot Pedal (20) into threaded hole in the left Crank (19). Turn the pedal shaft by
hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the threads.
Tighten the pedal shaft of Left Foot Pedal (20) with the Multi Hex Tool provided.
Insert pedal shaft of Right Foot Pedal (21) into threaded hole in right Crank (19). Turn the pedal shaft by hand
in the clockwise direction until snug. Tighten pedal shaft of Right Foot Pedal (21) with the Multi Hex Tool
provided.

9
STEP 2: SEAT POST, SEAT POST BELLOWS, AND SEAT CUSHION
INSTALLATION
Tool:
Multi Hex Tool
Hardware:
(8) Seat Post Knob M16x1.5
1 PC
Remove three Ø18xØ8x1.5t Washers (38) and three M8 Nylon Nuts (42) from underside of the Seat Cushion
(27). Remove nylon nuts with the Multi Hex Tool provided.
Guide bolts on underside of the Seat Cushion (27) through holes on top of the Seat Post (25), attach with three
removed Ø18xØ8x1.5t Washers (38) and M8 Nylon Nuts (42). Tighten nylon nuts with the Multi Hex Tool
provided.
Slide Seat Post Bellows (32) up onto the Seat Post (25).
Insert the Seat Post (25) into the Seat Post Bushing (12) on the tube of the Main Frame (1) and then attach the
M16x1.5 Seat Post Knob (8) onto the tube of the Main Frame (1) by turning it in a clockwise direction to lock
the Seat Post (25) in the suitable position.

10
STEP 3: HANDLEBAR POST INSTALLATION
Tool:
5mm Allen Wrench with Phillips Screwdriver
Remove four M8x16 Hexagon Socket Pan Head Cap Bolts (24) and four Ø18xØ8x1.5t Curve Washers (37) from
the Main Frame (1). Remove bolts with the 5mm Allen Wrench with Phillips Screwdriver provided.
Connect the Sensor Wire (26) from the Main Frame (1) to the Extension Sensor Wire (33) from the Handlebar
Post (3). It is recommended to have a second person assist with this step. One person should hold the Handlebar
Post (3) in place while the other person connects the sensor wires.
Put the cable end of resistance cable of Tension Control Knob (7) into the cable lock of Tension Cable (54), see
Figure A.
Pull the resistance cable of Tension Control Knob (7) up and force it into the slot of metal bracket of Tension
Cable (54), see Figure B.
Insert the metal fitting on the resistance cable of Tension Control Knob (7) into the hole at the end of the slot in
the metal bracket of Tension Cable (54), see Figure C.
Connect the resistance cable of Tension Control Knob (7) to Tension Cable (54) complete, see Figure D.
Carefully tuck wires into Main Frame (1) while sliding Handlebar Post (3) onto the tube of the Main Frame (1)
and secure with four M8x16 Hexagon Socket Pan Head Cap Bolts (24) and four Ø18xØ8x1.5t Curve Washers
(37) that were removed.
PLEASE FOLLOW THIS PROCEDURE TO TIGHTEN BOLTS WITH THE 5MM ALLEN WRENCH WITH
PHILLIPS SCREWDRIVER PROVIDED:
Tighten two M8x16 Hexagon Socket Pan Head Cap Bolts (24) in front of the Main Frame (1) first then the other
two M8x16 Hexagon Socket Pan Head Cap Bolts (24) on the side to secure the Handlebar Post (3) successfully.