Insportline Profigym N10 User manual

USER MANUAL - EN
IN 7185 Home gym inSPORTline Profigym N10

1
PARTS LIST DRAWINGS

2
PARTS LIST DRAWINGS

3
ASSEMBLY INSTRUCTIONS
STEP 1：
：：
：
1. Attach the Front Base Frame (2) to the Rear Base Frame (1), using two M10X60mm Hex
Bolts (54), four M10 Washers (62) and two M10 Nylon Nuts (66).
2. Attach the Weight Guide Frame (3) to the Rear Base Frame (1), using two M10X50mm Hex
Bolts (55), four M10 Washers (62) and two M10 Nylon Nuts (66).
3. Slide the Weight Plate Holder (5) down the Weight Guide Frame (3).

4
ASSEMBLY INSTRUCTIONS
STEP 2：
：：
：
1. Attach the Support Frame (8) to the Front Base Frame (2), using two M10X60mm Hex Bolts
(54), four M10 Washers (62) and two M10 Nylon Nuts (66).
2. Attach the Upper Cross Beam (9) to the Support Frame (8) and the Weight Guide Frame (3),
using four M10X60mm Hex Bolts (54), eight M10 Washers (62) and four M10 Nylon Nuts
(66).
3. Attach the two Single Pulley Blocks (14) to the Support Frame (8), using two M10X65mm
Hex Bolts (53), four M10 Washers (62) and two M10 Nylon Nuts (66).

5
ASSEMBLY INSTRUCTIONS
STEP 3：
：：
：
1. Attach the Front Support Frame (4) to the Front Base Frame (2), using one M10X60mm Hex
Bolt (54), two M10 Washers (62) and one M10 Nylon Nut (66).
2. Attach the Seat Base Frame (7) to the Support Frame (8) and the Front Support Frame (4),
using three M10X60mm Hex Bolts (54), six M10 Washers (62) and three M10 Nylon Nuts
(66).
3. Attach the Leg Extension Frame (6) to the Seat Base Frame (7), using one M10X60mm Hex
Bolt (54), two M10 Washers (62) and one M10 Nylon Nut (66).

6
ASSEMBLY INSTRUCTIONS
STEP 4：
：：
：
1. Attach the Back Cushion (22) to the Support Frame (8), using two M8X50mm Hex Bolts (58)
and two M8 Washers (63).
2. Attach the Seat Cushion (21) to the Seat Base Frame (7), using four M8X15mm Hex Bolts
(60) and four M8 Washers (63).
3. Insert the Foam Tube (17) into the Leg Extension Frame (6) and the Seat Base Frame (7),
then slide the Leg Foam Roller (23) onto the Foam Tube (17).

7
ASSEMBLY INSTRUCTIONS
STEP 5：
：：
：
NOTE: Oil Bushing (small) (31) have been Pre-assembled into the Upper Cross Beam (9).
1. Attach the Press Bar (10) to the Upper Cross Beam (9), using one M12X120mm Hex Bolt
(52), two M12 Washers (61) and one M12 Nylon Nut (65).
2. Remove two M12 Nylon Nut (65) and M12 Washer (61) from the Left Butterfly Arm (11) and
the Right Butterfly Arm (12).
3. Tap the Oil Bushing (Big) (32) to the Press Bar (10).
4. Attach the Right Butterfly Arm (12) and the Left Butterfly Arm (11) to the Press Bar (10),
using two M12 Washers (61) and two M12 Nylon Nuts (65).
5. Slide the Arm Foam Roller(24) onto the Right Butterfly Arm(12) and the Left Butterfly Arm
(11).
6. Remove two M10X20mm Hex Bolts(57) and M10 Washers(62) from the Handle Tubes(18).
7. Attach the Handle Tubes (18) to the Right Butterfly Arm (12) and the Left Butterfly Arm (11),
using two M10X20mm Hex Bolts (57) and two M10 Washers (62).
8. Slide two Middle-empty Plugs (□38X￠26) (43) and two Handle Grips (46) to the Right
Butterfly Arm (12) and the Left Butterfly Arm (11).
9. Attach the Tobacco-pipe (20) to the Support Frame (8), using one M8X40mm Hex Bolt (59),
two M8 Washers (63) and one M8 Nylon Nut (67).
10. Slide the Washer (∅30X∅10)(64) and the Plum Blossom Nut(30) onto the Tobacco-pipe
(20).

8
ASSEMBLY INSTRUCTIONS

9
ASSEMBLY INSTRUCTIONS