Intel Terasic FLIK User manual

FLIK Getting
Started Guide
1
www.terasic.com
April 30, 2020
1.1. Q

FLIK Getting
Started Guide
2
www.terasic.com
April 30, 2020
Contents
Chapter 1 Overview......................................................................................4
1.1 General Description.................................................................................4
1.2 Package Content .....................................................................................4
1.3 FLIK View.................................................................................................5
1.4 Block Diagram..........................................................................................6
1.5 Key Features............................................................................................7
1.6 Software Package and Manual ...............................................................8
1.7 Power On FLIK ........................................................................................9
1.8 Power Monitor Utility..............................................................................10
1.9 Function Test Guide............................................................................... 11
Chapter 2 Thunderbolt 3 Setup.................................................................12
2.1 Hardware Requirement .........................................................................13
2.2 Thunderbolt 3 Test.................................................................................13
Chapter 3 OpenVINO Setup for Windows................................................17
3.1 OpenVINO Installer/Demo Package .....................................................17
3.2 Install FLIK OpenVINO Runtime Environment .....................................18
3.3 Install FLIK OpenVINO Toolkit...............................................................25

FLIK Getting
Started Guide
3
www.terasic.com
April 30, 2020
Chapter 4 Power Monitor Setup................................................................29
4.1 Software Requirements.........................................................................29
4.2 Power Monitor Utility..............................................................................35
4.3 Getting Help...........................................................................................37

FLIK Getting
Started Guide
4
www.terasic.com
April 30, 2020
Chapter 1
Overview
his chapter provides an overview of the FLIK and installation guide.
1.1 General Description
With the rapidly-rising demand in today’s AI and compute-intensive applications,
Terasic’s FLIK (FPGA Client Innovation Kit) is a compact, all-in-one, adaptable
accelerator purpose-design to accelerate critical workloads such as data analysis,
deep learning, and machine learning algorithms directly on laptops or everything
portable! With a form factor slightly larger than a 2.5" external hard drive. It can be
placed vertically or horizontally to blend into various size-demanding environment.
FLIK takes advantage of the powerful Intel Arria 10 FPGAto enable higher speed data
processing. The kit is armed with 8GB DDR4-2133 on-board memory, providing around
4GB data transfer via PCIe Gen 3 interface between FPGA and laptops or host PC via
Thunderbolt™ 3 port. Also, with a form factor slightly larger than a 2.5" external hard
drive and closely packed in an aluminum body with advanced thermal solution, FLIK
takes care of the heat dissipation dynamically and is adaptable to various
size-demanding environment.
FLIK fully supports Intel Open VINO™ toolkit, Intel Acceleration Stack, and OpenCL in
both Linux and Windows versions. Our clients can achieve highest computing
performance, adaptability and lowest cost across broadest range of AI and deep
learning workloads.
1.2 Package Content
Figure 1-1 shows the package content of the FLIK kit.
T

FLIK Getting
Started Guide
5
www.terasic.com
April 30, 2020
Figure 1-1 FLIK Kit Content
1. FLIK
2. Thounderbolt3 Cable
3. FLIK Quick Start Guide
4. Power DC Adapter(12V)
5. AC Power Cord
1.3 FLIK View
Figure 1-2 shows the front and rear views of the FLIK. There are five color LED in front
panel. The five color LED indicate the status of FLIK. Table 1-1 shows the LED
indication meanings. There are a thunderbolt 3 port and a 12V DC input Jack on the
rear of FLIK.

FLIK Getting
Started Guide
6
www.terasic.com
April 30, 2020
Figure 1-2 FLIK View
Table 1-1 Front Color LED Indication
Front Color LED
Description
Green
FLIK is power on but not connected to Host PC.
Dark Blue
FLIK is just connected to the Host PC
Light Blue and Dark
Blue
FLIK is connected to the Host PC and show the power
consumption status. More Light Blue means more power
is consumed.
Red
FPGA power is shut down due to over temperature.
Orange
FPGA power is shut down due to power consumption
exceeds expectation.
Gray
FPGA power is shut down due to FPGApower
consumption exceeds expectation.
Yellow
FLIK is disconnected and will be auto shutdown in 60
seconds.
1.4 Block Diagram
Figure 1-3 shows the block diagram of the FLIK board.

FLIK Getting
Started Guide
7
www.terasic.com
April 30, 2020
Figure 1-3 Block diagram of the FLIK
1.5 Key Features
The following hardware is implemented on the FLIK board:
FPGA
Intel Arria ® 10 FPGA 10AX115N3F40E2SG
FPGA Configuration
On-Board USB Blaster II via Thunderbolt 3 Port
AS x4 configuration via QSPI Flash
Clock System
50MHz and 100MHz Oscillators
Programmable clock generators Si5340
Memory
Two Independent DDR4 banks, 4GB 1066MHz for each.
1024Mb QSPI Flash

FLIK Getting
Started Guide
8
www.terasic.com
April 30, 2020
Communication Ports
Thunderbolt 3 Port x1
PCIe Gen3x4 via Thunderbolt 3 Port
USB Blaster II port via Thunderbolt 3 Port
System Monitor and Control
FPGA Temperature Monitor
Board Temperature Monitor
Power Monitor
Auto Fan Speed Control
Auto Shutdown when temperature or power are abnormal.
LED Indication
Power Source
12V DC Input
1.6 Software Package and Manual
The FLIK Kit includes three software packages, as shown in Table 1-2. The software
packages are prepared for C/C++, OpenCL, and RTL developers. Table 1-3 shows the
documents provided by the FLIK Kit. The table also recommends manuals that
developers should study.
Table 1-2 Software Packages
Software Package
Required Programming Skill for FPGA
OpenVINO BSP
C/C++
OpenCL BSP
OpenCL
RTL Example Designs
RTL Coding
Table 1-3 Software Packages
Manual\Developer
OpenVINO
Developer
OpenCL
Developer
RTL
Developer
Quick Stat Guide
√
√
√
Getting Started Guide (Windows or Linux )
√
√
√
OpenVINO Development Guide
√

FLIK Getting
Started Guide
9
www.terasic.com
April 30, 2020
OpenCL User Manual
√
RTL Development Guide
√
1.7 Power On FLIK
There is no power SWITH on FLIK. Plug in 12V DC to FLIK will directly power on the
FLIK (See Figure 1-4). When FLIK is power on without connected to the Host PC, the
Font Panel Color LED is Green as shown in Figure 1-5.
Figure 1-4 Plug the DC 12V power to the FLIK

FLIK Getting
Started Guide
10
www.terasic.com
April 30, 2020
Figure 1-5 RGB Status LED when Power up
1.8 Power Monitor Utility
The FLIK Kit includes a Power Monitor Software which can be used to monitor the
power and temperature status of the FLIK, as shown in Figure 1-6. For more detailed
information, please check Chapter 4 : Power Monitor Setup.
Figure 1-6 Power Monitor

FLIK Getting
Started Guide
11
www.terasic.com
April 30, 2020
1.9 Function Test Guide
To perform function test on FLIK, users need to setup thunderbolt 3 first. For detail,
refer to Chapter 2 in this document. For OpenVINO developers, they need to install
OpenVINO Software. For detail, refer to Chapter 3 in this document.

FLIK Getting
Started Guide
12
www.terasic.com
April 30, 2020
Chapter 2
Thunderbolt 3 Setup
hunderbolt 3 is unique communication path between the Host PC and FLIK. As
shown in Figure 2-1, the FLIK use thunderbolt3 port to connect the PCIe and
USB Blaster II interface to the FPGA. For the OpenCL and OpenVINO
applications with the Intel FPGA, the PCIe bus is the main interface for communicating
and transferring data with the host PC. The thunderbolt3 port on the FLIK allows the
user to build such connection for the FPGAand the host PC via a thunderbolt3 cable.
In addition, the thunderbolt3 on the FLIK also provides an USB interface to connect to
the USB Blaster II circuit on the board, providing a JTAG interface for the user to
program the FPGAor configuration device through the host PC.
Therefore, a host PC equipmented with thunderbolt 3 port is required to work with the
FLIK. This chapter will show user how to setup thunderbolt 3 connection between the
Host PC and the FLIK for the first time. The windows OS is present in this chapter. For
Linux OS, please refer to the Linux Getting start guide.
Figure 2-1 The Thunderbolt interface of the FLIK
T

FLIK Getting
Started Guide
13
www.terasic.com
April 30, 2020
2.1 Hardware Requirement
AHost PC with Thunderbolt 3 Port is required to perform FLIK function Tests.
The PC should be:
Built-in Thunderbolt 3 Port or with Thunderbotl3 Card Installed.
Windows/Linux Installed
Thunderbolt 3 driver installed
A FLIK kit
AThunderbolt 3 Cable as shown in Figure 2-2
Figure 2-2 Thunderbolt 3 Cable
2.2 Thunderbolt 3 Test
Below shows the procedure when the FLIK is first time to plug into the thunderbolt 3
port of the Host PC.
1. Make sure your Host PC had installed Thunderbolt 3 Driver.
2. Plug 12V DC to FLIK to power on the FLIK.
3. Connect FLIK and host PC by a Thunderbolt 3 cable.

FLIK Getting
Started Guide
14
www.terasic.com
April 30, 2020
Figure 2-3 Plug the Thunderbolt 3 cable to the FLIK
4. When the host pc connects to the FLIK with Thunderbolt 3 cable for the first time.
Windows should detect a Thunderbolt Device and you will see a “New
Thunderbolt device has been connected”message appear in the bottom right
corner of your screen as shown in Figure 2-4. Click the message to approve the
device.
Figure 2-4 New Thunderbolt devices have been attached" message
Note, if thismessage does not appear, user can reconnect the thunderbolt 3 cable
between the FLIK and Host PC or power off and on the FLIK. If the message still
doesn't appear, please refer to the below link to fix it: Setup Thunderbolt3
connection win10
5. A Thunderbolt Dialog window will appear as shown in Figure 2-5 or Figure 2-6.
Select “Always Connected” and click OK button.

FLIK Getting
Started Guide
15
www.terasic.com
April 30, 2020
Figure 2-5 Approve Thunderbolt device window
Figure 2-6 Approve Thunderbolt device window
6. Open the "Device Manager" in the Windows and you will see the "PCI Device"
and "Unknown device" on the"Other devices" item (See Figure 2-7). It shows that
the PCIe device and USB Blaster II circuit on the FLIK are correctly detected by

FLIK Getting
Started Guide
16
www.terasic.com
April 30, 2020
the host PC. The following chapter will show how to install the drivers for these
two devices.
Figure 2-7 Host PC detects the PCIe and USB Blaster II function in the FLIK

FLIK Getting
Started Guide
17
www.terasic.com
April 30, 2020
Chapter 3
OpenVINO Setup for
Windows
penVINO is a high-level development kit. Users can accelerate the
computing by high-level C/C++ language rather than low-level RTL coding.
This chapter introduces how to install OpenVINO run-time environment and
how to performance OpenCL demo on Windows 10. Before setup the OpenVINO,
please make sure the thunderbolt3 driver is installed on the Host PC.
3.1 OpenVINO Installer/Demo Package
First, users need to download the OpenVINO BSP for windows
“FLIK_OpenVINO2019R1_windows.zip”from the link: http://flik.terasic.com/cd.
Figure 3-1 OpenVINO BSP for Windows
Then, uncompress the.zip file into your Host PC. There are two folders in the
compressed file.
Figure 3-2 Contents of the demo package
The "OpenVINO2019R1_windows" folder has the relevant file for installing
OpenVINO tool kit in the window. The "terasic_demo_windows" folder contains demo
examples for using OpenVINO with the FLIK.
O

FLIK Getting
Started Guide
18
www.terasic.com
April 30, 2020
3.2 Install FLIK OpenVINO Runtime
Environment
1. Install required Microsoft Visual Studio runtime library : Visual Studio 2017
Redistributable Package
Figure 3-3 Web site of the Visual Studio 2017 Redistributable Package
2. Open the folder “OpenVINO2019R1_windows”you just extracted (section 3.1).
Before install the drive of the FLIK and setup associated environment, please open
and read the “Intel OBL Commercial Use License.pdf” for Software License
Agreement.
3. Go to the path “/OpenVINO2019R1_windows/FLIK-Windows-Install_19.2”and
execute “1-SetBootOptions.bat” as an Administration to enable test-signed code
and device driver signing of the windows, as shown in Figure 3-4 and Figure 3-5.
Figure 3-4 The FLIK-Windows-Install folder

FLIK Getting
Started Guide
19
www.terasic.com
April 30, 2020
Figure 3-5 Run 1-SetBootOptions.bat as administrator
4. When the batch file is executed, please reboot the system to enable the settings.
Figure 3-6 1-SetBootOptions.bat is executed
5. After Reboot Windows, open “Command Prompt”and run as “administrator”.

FLIK Getting
Started Guide
20
www.terasic.com
April 30, 2020
Figure 3-7 Open Command Prompt
6. Go to the folder “FLIK-Windows-Install_19.2” and execute “2-InstallDcpBsp.bat”.
It will start to install Intel Runtime Environment for OpenCL.
Figure 3-8 Run “2-InstallDcpBsp.bat”as administrator
7. Press “y”when ask to install FLIK device driver.