International Concepts BROKLYN BD-8006 User manual

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 6 DRAWER DRESSER RTA
: BD-8006

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
N
O
Descriptio
n Qty Sketch NO Description Qt y Sketch
A Top 1 B Bottom panel 1
C Vertical
panel 1
D Side panel (L-R) 2
E Back rail 1
F
Back panel
2
G Support
leg 1 H Drawer side (L&R) 12
I Drawer
front 6
J Drawer back 6
K Drawer
bottom 6
M Support bar 6

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Bolt
(M6x30mm) 14
7 Knob 12
2 Spring washer
()6.5x11mm) 14
8 Screw
(M4x30mm) 12
3 Flat Washer
()6.5x13mm) 14
9 Steel band 1
4 Allen key
(M4x80mm) 1
10 Warning label 6
5 Screw
(M4 x 35mm) 76
11 Screw
(M3X15mm) 2
6 Pan head screw
(M4 x 30mm) 12

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 5 -
STEP 1
Attach the top (A), and bottom panel (B) to vertical panel (C) with bolts (1) and washers (2) and (3)
.Tighten with Allen key (4).
STEP 2
Attach the top (A), and bottom panel (B) to a side panel (D) with bolts (1) and washers (2) and (3)
.Tighten with Allen key (4).
Slide back panel (F), and back rail (E) into the groove as shown below.

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 6 -
STEP 3
Attach the top (A), and bottom panel (B) to the other side panel (D) with bolts (1) and washers (2)
and (3). Tighten with Allen key (4).
Attach support leg (G) to vertical panel (C) with bolts (1) and washers (2) and (3) .Tighten with Allen
key (4).
STEP 4
Attach back rail (E) to side panels (D) with screws (5) .Tighten with a screwdriver.
Attach the steel band (9) to Chest with screws (11).

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 7 -
STEP 5
Attach drawer sides (H) to drawer front (I) with screws (5) as shown below. Tighten with a screwdriver
Insert drawer bottom (K) into the grooves at bottom of drawer sides (H), drawer front (I) as shown
below.
STEP 6
Attach drawer back (J) to drawer sides (H) with screws (5) as shown below. Tighten with a
screwdriver.

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 8 -
STEP 7
Attach support bars (M) to bottom of drawers with screws (8) as shown below. Tighten with the
screwdriver.
Attach knobs (7) to front of drawers with screws (6). Tighten with the screwdriver.
Stick the warning labels (10) inside the drawers before use.
STEP 8

ITEM NO: BD-8006
REVISED APR 08, 2015
Printed in Vietnam
- 9 -
Attach steel band (9) to the wall with screw (5) as shown below (to secure the product and prevent
tipping).
STEP 9