International Concepts FRANKLIN TV-56 User manual

ITEM NO.: TV-56
REVISED JAN 16, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: FRANKLIN 54 IN ENTERTAINMENT CENTER
: TV-56

ITEM NO.: TV-56
REVISED JAN 16, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-56
REVISED JAN 16, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Side panel
(L-R)
2
B
Bottom panel
1
G
Vertical panel
(L-R)
2
C
Center Shelf
1
H
Side shelf
2
D
Door (L-R)
2
I
Back panel
1
E
Glass
2
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6x30mm)
16
7
Allen Key
(M4x80mm)
1
2
Spring washer
(6.5x11mm)
16
8
Short pan head
screw
(M3x15mm)
24
3
Flat Washer
(6.5x13mm)
16
9
Screw
(M3x15mm)
16
4
Wooden knob
(38x30mm)
2
10
Magnet
2
5
Long pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
11
Bracket
12
6
Door pin
(5.2/13x1.2mm)
(7x10mm)
4
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2

ITEM NO.: TV-56
REVISED JAN 16, 2016
Printed in Vietnam
- 4 -
STEP 1
Attach glass sections (E) to back of doors (D), and lock it.
Attach knobs (4) to doors (D) with pan head screws (5) as shown below. Tighten with a screwdriver.
STEP 2
Attach panels (G) to top (A) and bottom panel (B) with bolts (1), and washers (2) and (3) as shown
below. Tighten with Allen key (7).
Attach doors (D) to top (A) and bottom panel (B) with door pins (6).
Attach magnet (10) to top (A) with screws (9) as shown below. Tighten with the screwdriver.

ITEM NO.: TV-56
REVISED JAN 16, 2016
Printed in Vietnam
- 5 -
STEP 3
Attach side panels (F) to the unit with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (7).
STEP 4
Attach back panel (I) to the unit with pan head screws (8) as shown below. Tighten with the
screwdriver.
STEP 4
STEP 5 (FINISH)
Attach brackets (11) to the unit. Place the shelves (C) and (H) on the brackets, and attach with
screws (9) as shown below. Tighten with the screwdriver.