International Concepts CU-15 User manual

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: MEDIA CABINET RTA
: CU-15

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Crown
1
B
Door
1
C
Side panel
(R)
1
D
Side panel
(L)
1
E
Bottom
shelf
1
F
Shelf
1
G
Adjustable
Shelf
4
H
Rail
1
I
Back panel
1
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Long bolt
(M6x35mm)
12
2
Flat washer
(ɸ6.5x19mm)
12
3
Lock washer
(ɸ6.5x11mm)
12
4
Bracket
16
5
Short pan head
screw
(M3.5x15mm)
4
6
Short screw
(M3.5x15mm)
27
7
Long screw
(M4x30mm)
3
8
Knob
(ɸ30x30mm)
1
9
Long pan head
screw
(M4 x 25mm)
1
10
Steel band
1
11
Allen key
(M4x80mm)
1
HARDWARE LIST

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 4 -
STEP 1
Attach shelf (F) and bottom shelf (E) to left side panel (D) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (11).
EP
=
Insert rail (H) into side panels (C) and (D) as shown below. Then attach shelves (E) and (F) (from step 1) to
right side panel (C) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (11).
STEP 2

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 5 -
Attach rail (H) (from step 2) to crown (A) with screws (7) as shown below.
Attach side panels (C) and (D) (from step 2) to crown (A) with bolts (1), and washers (2) and (3) as
shown below. Tighten with Allen key (11).
Slide back panel (I) into grooves of top (A), and side panels (C) and (D). Then attach back panel to
the unit with pan head screws (5) as shown below. Tighten with a screwdriver.
STEP 3
STEP 4

ITEM NO. : CU-15
REVISED MAR 24, 2016
Printed in Vietnam
- 6 -
STEP 5
Attach door (B) to the unit with screws (6) as shown below. Tighten with a screwdriver.
Attach knob (8) to door (B) with pan head screw (9) as shown below. Tighten with a screwdriver.
Attach brackets (4) to side panels (C) and (D) as shown below. Then place the adjustable shelves (G)
on the brackets and attach with screws (6). Tighten with a screwdriver.
Attach steel band (10) to the unit with screws (6) and attach steel band (10) to the wall with screw (7)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
STEP 6