Invacare SoftAir EXCELLENCE User manual

SoftAir EXCELLENCE 250mm Alternating Mattress System
User Manual

2
SoftAir EXCELLENCE User Manual
Important Notice
Before operating this medical equipment, it is
important to read this manual and understand
the operating instructions and safety
precautions. Failure to do so could result in
patient injury and/or damage to the product.
If you have any questions, please contact
your local Invacare sales office. Please refer
to the back page for contact details.

3
Contents
SAFETY PRECAUTIONS. . . . . . . . . . . . . . . 4
PRODUCT OVERVIEW . . . . . . . . . . . . . . . . 5
INSTALLATION ......................6
Unpacking & Inspection . . . . . . . . . . . . . . . 6
System Installation . . . . . . . . . . . . . . . . . . . 7
Control UnitActivation. . . . . . . . . . . . . . . . . 7
OPERATION.........................8
Control Unit Panel. . . . . . . . . . . . . . . . . . . . 8
Mattress Function . . . . . . . . . . . . . . . . . . . . 9
Alarm Functions . . . . . . . . . . . . . . . . . . . . 10
Removal & Transport Function . . . . . . . . . 11
TROUBLESHOOTING . . . . . . . . . . . . . . . . 12
CLEANING.........................14
MAINTENANCE.....................16
TECHNICAL SPECIFICATIONS . . . . . . . . 17
WARRANTYINFORMATION. . . . . . . . . . . 18
SoftAir EXCELLENCE 250mm Alternating Mattress System

4
In General
Safety Precautions
Do not use this equipment in the presence of
flammable anesthetics.
Bed frames used with the systems can vary
greatly depending on the specific health care
setting (i.e. hospitals, nursing homes, home
care).A risk assessment must be performed
by a suitably qualified person, especially when
side rails are prescribed, to ensure the bed
meets the new IEC 60601-2-52 bed standard.
Arisk assessment must be undertaken when
looking to place additional items between the
mattress surface and patient.
To ensure the alternating cells move effectively,
secure the bed sheets loosely around the
mattress.
Control Unit
The control unit is tested and approved
according to ISO-EN 60601-1 rev.2 & EMC
Only plug into a grounded power outlet and use
the power cord supplied with the system.
Exposure of the electronic Control Unit to any
liquid while it is plugged in could result in a
severe electrical hazard.
Always use fuses of the same rating as specified
in the Technical section. Using fuses with higher
ratings could result in damage and/or injury.
The electronic Control Unit is a precision
electronic product. Handle and transport with
care. Dropping or other sudden impacts may
result in damage to the unit.
Do not open the Control Unit due to risk of
electrical shock. Do not attempt to repair or
service the Control Unit.
Do not place any objects or items such as
blankets on or over the Control Unit.
The power cord to the Control Unit should be
positioned to avoid a trip hazard and/or damage
to the cord. Careful consideration is required
when routing the power cable. Invacare Ltd
recommends placing the cord under the bed
frame and attaching it to an electrical outlet at the
head of the bed.

5
Product Overview
SoftAIR Alternating Mattress System
The SoftAIRExcellence isa alternatingmattress system
thatprovidespressureapplication andreleasetopatients
who are vulnerabletoorsufferfrom pressure ulcers.Itis
designedtoreplace anexistingmattressand can beused
onboth standard and profilingbedframes.
Digital Control Unit
The ControlUnit providesthe airsupplytothe mattress.
• It is controlled via a touch panel with integrated
digital display. The alarm sounds when pressure
fails or power is interrupted. TheAlarm Mute
button silences the alarm for a maximum of 20
minutes. The alarm resumes if cause of failure is
not resolved.The alarm will sound for up to two
hours following an interruption to power.As soon as
power is restored, the battery memory back up will
restore the latest pressure/ user settings.
• The Control Unit is fitted with an ‘on board’ battery.
The battery powers the alarm sounder in the event
of a total power failure or power interruption.
• The buttons on the control panel adjust the eight
comfort level settings.
• The system will automatically revert to Alternation
Mode after 20 minutes in Static Mode. See page 8
for further instructions.
• TheAlarm LED indictor and Alarm Mute completes
the profile.
The visible and audible alarm function has a number of
indications depending on the cause of the failure.
Ontheside ofthecontrolunitarefour maleair connectors
for connectingthehandle.
Therapidreleasehandleincludesacapwhichcanbe
insertedintothehandleduringtransportation.Whenin
transportationmode,testshaveproventhatthesystem
willstayinflatedforupto30hourswithnosignificantlossof
pressure.Whilstintransportationmode,themattresswill
remaininstaticmode(i.e.cellswillnotalternate).Forthis
reason,Invacarerecommendthatthealternatingmodeis
resumedoncetransportationiscomplete.
The mains supply to the Control Unit can be easily
disconnected and is designed to detach if tugged too
hard, protecting the internal wiring.
SoftAIR Excellence
The SoftAIR Excellence Mattress comprises of 19 high
density cells which all feature a permanently inflated
internal cell to prevent the patient “bottoming out” in
the event of low pressure due to incorrect settings,
electrical or cell failure.
This system includes three static head cells to provide
static “pillow” support for optimum user comfort, while
air pressure in the other 16 cells is alternated over a
10-12 minute cycle. This provides regular periods of
pressure reduction to aid blood and lymphatic flow to
vulnerable tissue.
The SoftAIR Excellence also includes an independent
heel zone of five low pressure micro cells for
individualised therapy to this sensitive area.
In addition, two permanently inflated side formers assist
in lateral support for the user and carer while increasing
the effectiveness of the one in three alternation cycle.
The hinged mattress base conforms to movements of
a profiling bed .

6
Installation
Unpacking & Inspection
NOTE: It is recommended that all packing materials
and instructions are kept in the carry bag provided in
the event of the product being shipped to your local
Invacare Ltd sales office.
Carefully remove the Control Unit, mattress and
accessories from the shipping cartons. Inspect all
items for any damage that may have occurred during
transportation.Any damaged or missing parts must
be reported to your local Invacare Ltd sales office
immediately. Please refer to the back page for contact
details.
SoftAIR Excellence
The shipping carton contains a complete and
readily assembled mattress system consisting
of:
• SoftAIR Excellence mattress system
including mattress base, CPR tag, air
hoses, handle with transport cap attached
and two inflatable side formers
• Carry Bag
• Digital Control Unit
• Medical grade power cord
• Quick setup guide
• User manual.

7
The following describes the procedures for initial
system set up.
a. Remove all covers, sheets and the mattress from
the bed.
b. On a standard bed, position the mattress on top of
the bed frame with the top cover facing upwards.
The air hoses should be at the foot end of the bed
for positioning of the Control Unit.
c. Attach the mattress to the bed by securing the
two adjustable straps under each end of the bed.
Ensure buckles are securely fastened and straps
are pulled tight.
On a profiling bed, secure the adjustable straps
around the profiling sections of the mattress
platform.
d. To avoid any risk of damage to the mattress ensure
there are no sharp objects which may come into
contact with it.
Check that the attachment of the Mattressdoes
not interfere withthemovement or operation of
the bed. Do not secure straps to bed side rails
as straps will tear.
a. Position the Control Unit by placing the hooks over
the foot board of the bed or side rails.
b. Connect the handle to the Control Unit. Ensure the
air hose does not kink between the bed frame and
Control Unit.
c. Insert the power cord into the Control Unit,
then plug into a grounded 220V 50Hz electrical
outlet.
d. Press the power button for at least two seconds to
activate the Control Unit.
The pressure LEDs will flash indicating the system
has activated. For detailed operation instructions,
see Page 8: Control Unit Panel.
e. Please allow up to a maximum of 50 minutes for
the mattress to fully inflate. Once ready, the first
four pressure LED’s plusAlternating Mode LED will
illuminate to indicate that the system is ready for use
(system automatically defaults toAlternating Mode after
start-up)
f. Once the Mattress is fully inflated the bedding can
be placed. Fit sheets loosely enough to allow for free
movement of the mattress air cells.
Installation
System Installation Control Unit Activation

8
Operation
Control Unit Panel
APower Button
Turns system power on and off.
BAlarm LED
The red light will flash and an audible alarm will sound
to alert when the Control Unit or mattress pressure
fails. The alarm has five different signals to indicate the
cause of the failure.
The audible alarm also sounds when power is switched
off. Press theAlarm Mute to silence.
CAlarm Mute Button
This button silences the audible alarm (on/ off).Audible
alarm will resume after 20 minutes if cause of failure is
not resolved.
DMode Button
Press to select eitherAlternation Mode (alternative
cells cyclically inflating and deflating) or Static Mode
(all cells fully inflated with no dynamic alternation).
Static Mode will automatically revert back toAlternation
Mode after 20 minutes.
EPressure Arrow Buttons
Press the arrows to increase or decrease the pressure
setting. Eight pressure settings are available from soft
to hard (18mmHg to 60mmHg; 6mmHg per step). The
green LEDs illuminate to indicate which of the eight
settings is operational.
F Max Firm Button
Press to facilitate rapid inflation to maximum pressure
setting (60mmHg).After 30 minutes,
the system automatically reverts back to the previous
pressure setting for patient safety.
GControl Unit Lock / Unlock Button
Press for at least two seconds to lock the Control
Unit settings.A beep sounds and the amber LED
illuminates to indicate system is locked. When locked,
only theAlarm Mute and Lock / Unlock buttons remain
operational.
Press again for at least two seconds to unlock.Again a
beep sounds and the amber LED turns off.
The Control Unit will automatically unlock
in the event of a power failure.
G
AB C D E F
<
<

9
Establishing Pressure
(supine/ face up position)
Once the patient is in place, use the Pressure button
to select the best setting for effective pressure relief
and support, based on the patients weight and comfort
requirements.
Assess whether the patient is comfortable and the
system is functioning correctly by performing a
‘bottoming out’ test.
Bottoming Out Test
When altering the pressure setting, ensure the patient
is not ‘bottoming out’ (insufficiently supported by the
air cells and therefore coming in contact with the bed
base).
1. Ensure system is in alternation mode but is not
undergoing an alternation.
2. With the patient lying in a supine position, unzip the
top cover, just past the sacral (bottom) region.
3. Slide your hand along a deflated cell under the
patients sacral area (bottom). The inner static
cell will remain inflated but your hand should slide
easily between the patient and the base.
4. If your hand can pass under the patient, the patient
is adequately suspended and pressure can be
lowered.
5. Repeat the Bottoming Out test after pressure has
been lowered.
In the event of a system malfunction, the alarm will
activate and pressure LEDs will flash.
Establishing Pressure
(inclined position)
When moving the patient to a more upright position,
pressure may need to be increased (by approximately
20%) to provide added support and to avoid ‘bottoming
out’.
It is important to return to the original pressure
setting when the patient returns to the supine
position, and perform a Bottoming Out test.
Wait a minimum of 10-12 minutes between
pressure adjustment and patient assessment,
as it may take a full cycle for the system to
adjust to any new setting.
CPR Function
Rapid deflation of the mattress may be required
for emergency procedures or to decommission the
system. Firmly pull the rapid release CPR tag from the
side of the mattress to deflate the whole system.
To re-inflate the system after the CPR tag has been
removed, replace the CPR tag ensuring both sealing
connectors are firmly attached and restart the Control
Unit. Wait for the mattress system to gain optimal
pressure.
Perform a Bottoming Out test after inflating the
mattress following rapid deflation.
Operation
Mattress Function

10
Alarm Function
The redAlarm LED will flash and an audible alert will
sound to indicate the control unit or mattress pressure
has failed. The LED will remain illuminated until
appropriate pressure is restored.The audible alarm
can be silenced by pressing the Alarm Mute button.
The system has five different alarm signals
which can be identified by five different Pressure
Setting illumination sequences.The signals and
corresponding Pressure Setting LED displays are
illustrated below
Operation
Display Alarm Signal
Initial Failure Mattress has failed to reach minimum operational
pressure within 50 minutes
Low Pressure Pressure has fallen 5mmHg or more below the setting
minimum
High Pressure Pressure has exceeded the maximum setting by
10mmHg or more
Alternating Mattress has failed to commence alternation
Mode failure
AC power failure No pressure output due to mains power failure
If the alarm activates and the system fails to inflate or
loses pressure, please refer to the Troubleshooting
section on the following pages.

11
Operation
Transport Function
1. Prior to transport, switch the mode from
alternating to static and wait five minutes for the
cells to inflate to maximum pressure.
2. Turn off the Control Unit and remove the rapid
release handle from the Control Unit.
3. Allow air to escape for a couple of seconds before
sealing with the attached transport cap. This will
soften the mattress surface for pressure relief
and comfort. If the patient is responsive, question
their comfort level based on current pressure and
adjust accordingly.
Invacare recommend that the alternating mode is
resumed once transportation is complete.
Regularly perform a ‘Bottoming Out’test to
ensure the patient is appropriately supported
as air pressure is released from all internal
static cells as well as alternating sections.
System Removal
1. Switch off the Control Unit and disconnect from
mains supply.
2. Remove the rapid release handle from the Control
Unit and disconnect the CPR tag.
3. Place the Control Unit and power cord on top of
the mattress and detach it from the bed frame.
4. Once the air has been released from all the cells,
roll up the mattress and return all items to the
Carry Bag for safe keeping.
Prior to restarting the system, ensure the
CPR tag is replaced and both sealing
connectors are firmly attached. Replace the
rapid release handle and firmly connect to the
Control Unit.

12
Troubleshooting
Control Unit does not
operate; no display
lights illuminate
The Control Unit may
not be attached to a
power source
Afuse may need
replacing in the
Control Unit
1. Check the Control Unit is connected to mains power outlet
with the correct voltage.
2. Check the Control Unit is switched on.
3. Check the mains plug fuse (3AMP) then check both
Control Unit fuses (1AMP) – fuses can be released using a
screwdriver to push and turn.
Do not try to open the Control Unit. Opening the unit
could cause personal injury or equipment damage.
Ensure the replacement of fuses is carried out in
accordance with local legislation.
Alarm LED
+ audible alarm
Pressure too low 1. Reset the alarm – turn off Power and press theAlarm Mute
button.
2. Check the handle is intact, ensuring all four sealing
connectors are firmly fitted to the Control Unit and the air
hoses. Check the CPR tag is attached and both sealing
connectors are firmly secure.
3. Check all air hoses along the inside of the mattress – each
should be firmly connected. Check each air cell is securely
attached to its connecting air pipe.
4. Check all cells, pipes and hoses for any air leakage.
5. Check that the air filter cover is correctly secured and the
air filter is clean.
6. Switch on Power.
Alarm LED
+ audible alarm
Initial failure 1. Reset the alarm – turn off Power and press theAlarm Mute
button.
2. Check the handle is intact, ensuring all four sealing
connectors are firmly fitted to the Control Unit and the air
hoses. Check the CPR tag is attached and both sealing
connectors are firmly secure.
3. Check all air hoses along the inside of the mattress – each
should be firmly connected. Check each air cell is securely
attached to its connecting air pipe.
4. Check all cells, pipes and hoses for any air leakage.
5. Switch on Power.
Alarm/ Fault Cause Solution
This section provides basic troubleshooting support for the SoftAIR Excellence mattress system.

13
Troubleshooting
AC power failure
If the problem is not resolved, please contact
your local Invacare Ltd sales office.
1. Press theAlarm Mute button to silence the audible alarm.
2. Check the power cable is firmly plugged into the mains
outlet and the Control Unit; and check the mains power is
switched on.
3. Check the Control Unit fuse (1AMP) – fuse can be
released using a screwdriver to push and turn.
Alarm LED
+ audible alarm
Pressure too high 1. Reset the alarm – turn off Power and press theAlarm Mute
button.
2. Disconnect the air hoses to reduce pressure – reconnect
when pressure has decreased.
3. Check for twists in the air hoses between the mattress and
Control Unit.
4. Switch on Power.
Patient is sinking or
“bottoming out” whilst lying
flat on the mattress
The pressure may
be set too low for the
patient’s weight
1. Increase the pressure setting by pressing up the Pressure
arrow.
2. To check effective system performance, conduct a
“Bottoming Out” test as described on page 9.
Alarm LED
+ audible alarm
Alarm LED
+ audible alarm
Alternating
Mode Failure
(no alternation)
1. Reset the alarm – turn off Power and press theAlarm Mute
button.
2. Disconnect the air hoses to reduce pressure – reconnect
when pressure has decreased.
Alarm/Fault Cause Solution

14
Maintenance & Cleaning
Infection Control and routine cleaning must be carried
out in accordance with your local Infection Control
Policy. It is suggested that all disinfection be done with
a high grade disinfectant such as Sodium Hypochlorite
or similar (up to 10,000 ppm available chlorine).
The top cover seams are sealed to prevent
moisture ingress and bacterial growth in the
seam stitching.
Do not use high temperature autoclave or
Phenolic based products for cleaning.
It is recommended the system is cleaned
between patients and approximately every two
weeks if in constant use.
Mattress Top Cover
If there are visible signs of body fluids and/ or
substances present, the top cover should be washed.
Top covers can be machine washed (up to 95ºC) using
disinfectant such as Sodium Hypochlorite or similar (up
to 10,000 ppm available chlorine).
To establish the amount of disinfectant to use,
determine the amount of water in the washer and then
follow the manufacturers’ instructions for dilution.
Soak the top cover in the disinfectant during the wash
cycle. Rinse well in clean water and dry thoroughly
before use.
Do not dry the top cover using the
heat cycle or a dryer. Please air dry or select a
non-heat dry cycle.
If there are no visible signs of body fluids and or
substances on the top cover, the top cover should be
sanitised.
1. Apply an intermediate level disinfectant (or a
solution of Sodium Hypochlorite or similar up to
10,000 ppm available chlorine) to the top cover
upper surface either by spraying or by hand
application.
2. Ensure the surface is completely covered with
the disinfectant and remains in contact with the
surface according to manufacturer’s instructions.
3. Remove disinfectant and rinse thoroughly.
4. Allow to air dry before use.
Mattress Base
Wipe down the outside shell with disinfectant (or a
solution of Sodium Hypochlorite or similar up to 10,000
ppm available chlorine), ensuring that all surfaces
come in contact with the disinfectant. Rinse off well with
a clean damp cloth and air dry.
Should the air cells require disinfecting, disconnect
the air cells from the base by unfastening the press
studs at each end and disconnect the air pipes from the
main air hoses before sliding each cell out from the cell
straps. Swab with a solution of Sodium Hypochlorite
or similar (up to 10,000 ppm available chlorine). Dry
thoroughly with a soft cloth before refastening.
Do not machine wash or dry the
air cells or mattress base.
Do not disassemble the mattress unless
cleaning is required. If cleaning or disinfecting
is required, do not disconnect the pipes from
individualAir Cells.

15
Maintenance & Cleaning
Handle
The exterior of the Handle can be
periodically wiped using a cloth
dampened with disinfectant.
Control Unit
Ensure the Control Unit is disconnected from the
mains electricity supply before cleaning.
Do not spray disinfectant directly on to the
Control Unit, or immerse the Control Unit in
any type of liquid. This could result in a severe
electrical hazard as this equipment has no
protection against ingress of water.
This equipment is not suitable for use in the
presence of a flammable anesthetic mixture with
air or with oxygen or nitrous oxide.
Wipe down Control Unit with warm water containing
detergent (or with a solution of Sodium Hypochlorite or
similar) and dry thoroughly before use.
Air Filter Replacement
1. Switch off the power supply to the
Control Unit.
2. Disconnect the power cord and air hoses.
3. Place the Control Unit on a flat surface with its back
panel uppermost (place soft cloth under unit to
prevent scratches).
4. Carefully remove the air filter cover. Remove and
discard the filter and fit with a new filter (there may
be a small locking screw – use a small Phillips Head
screwdriver to remove this first).
5. RefittheairfiltercovertotheControl Unit.The Control
Unit is now ready for re-connection.
Good filter maintenance is critical to maintain
your SoftAIR system to optimal operating
condition. Failure to keep the filters clean will
result in system downtime and increase repair
costs. It is recommended that the air filter be
replaced annually. Replacement air filters are
available from your local Invacare Ltd sales
office.
Fuse Replacement
1. Switch off the power supply to the Control Unit.
2. Remove the power cord from the electrical socket
on the side of the Control Unit.
3. Insert a small flat head screwdriver into the groove
and turn anti-clockwise (1/4 turn).
4. Remove the “blown” fuse from the fuse holder clip
and discard.
5. Insert a new fuse into the plug. Push against the
force of the spring and turn clockwise with the
screwdriver (1/4 turn).
Ensure the replacement of fuses is carried out
in accordance with local legislation.

16
Technical Specications
Cycle Control Purpose designed distributor valve
supplying operating air to the inflatable cells
Cycle Time 12 minutes
Supply Voltage 220V, 50Hz
0.2Afor Control Unit
IP Rating IP41
Fuse Rating 1AMP (x1)
Battery Source VARTA, V80H, 1.2Vdc, 70mAh
Power Rating 12VA
Standards CE
No of Cells 19 (cell in cell) including 3 static head cells
and 5 micro cells plus 2 side bolsters
Cell Height 230mm
Maximum Patient Weight 180kg
Product Life Cycle 2 Years
Mattress Dimensions Length 2000mm
Width 830mm / 880mm
Height 250mm (including side formers)
Weight 9.5kg / 10.8kg
Control Unit Dimensions Length 290mm
Width 170mm
Height 270mm
Weight 3.2kg
Cell Material 0.15mm TPU film laminated on 210 denier nylon fabric
Base Material Nylon fabric 420 denier with a 0.1mmTPU coating
Cover Material 100% Polyurethane surface, 100% polyester inside
Hose Connection Push on connection Handle
Emergency CPR Tag
Mode of Operation Non-continuous
Operating Environment Air humidity 30% to 70%
Ambient temperature 10ºC to 40ºC
Storage/Transportation Air humidity 10% to 70%
Environment Ambient temperature -10°C to 60°C
NOTE:All product specifications are subject to change without notice.
SoftAIR Excellence

17
Invacare Ltd warrants each of its products to perform
in accordance with established specifications for
the following time periods, starting from the date the
product is shipped from Invacare Ltd.
Control Units 2 years
Soft Goods 2 years
During the warranty period, Invacare Ltd either directly
or through its distributors, will repair or replace at
no charge, any products that are not performing in
accordance with established specifications, unless the
problem/ failure is due to:
• customer damage, negligence and/ or misuse
• unauthorised repairs
Items not covered under warranty include, but are
not limited to, stains, punctures, cuts, damages
to electrical cords, rips or tears, dents and/ or lost/
missing parts.
All products returned for warranty repairs must be
assigned a Return Autho risation Number prior to
return. Returns should include information describing
the problem and or requested repair and be sent
to your local Invacare Ltd sales office by prepaid
transportation. Invacare Ltd will return the repaired/
replaced product at no charge. Warranty repairs do not
extend the length of the warranty period.
Neither Invacare Ltd, its distributors, officers, directors,
employees or agents shall be liable for consequential
or other damages, including but no limited to personal
injury, loss, or any other expense, directly or indirectly
arising from the use of its products. The sole remedy
for breach of the limited warranty granted herein shall
be repair or replacement or the Invacare Ltd products.
Warranty Information
Product life Cycle
The product life cycle quoted can be exceeded if the
product is maintained as per Invacare maintenance
and cleaning guildlines,The life cycle can also be
considerably reduced if the guildlines for maintenance
and cleaning are not followed or by unintended use

18
Invacare UK Ltd.
PencoedTechnology Park, Pencoed, Bridgend, CF35 5AQ, UK
Tel: [phone] Fax: [phone]
Technical Services Tel: [phone] Fax: [phone]
Invacare Denmark
Invacare EC-Høng A/S
Østergade 3, DK-4270 Høng, Denmark
Tel: [phone] Fax: [phone]
Invacare Norway
Invacare AS
Grensesvingen 9, Postboks 6230, Etterstad, N-0603 Oslo, Norway
Tel: [phone] Fax: [phone]
Invacare Sweden
Invacare AB
Fagerstagatan 9, S-163 91 Spånga, Sweden
Tel: [phone] Fax: [phone]
Invacare Ireland Ltd.
Unit 5, Seatown Business Campus, Seatown Road, SWORDS. County Dublin
Tel: [phone] Fax: [phone]
www.invacare.com
Part number: 1550997