involight COBPAR100T User manual

Bedienungsanleitung
User manual
COBPAR100T
www.destilan-deutschland.de

1
Table of contents
INTRODUCTION ……………………………………………….…………………………..2
SAFETY INSTRUCTIONS…………………………………………………………………2
OPERATING DETERMINATIONS…………………………………………….…………..3
DESCRIPTION OF THE DEVICE…………………………………………………………4
INSTALLATION………………………………………………………………….…………..5
OPERATION……………………………………………………………………….………...6
Stand alone operation…………………………………………………………….…………6
Master slave operation…………………………………………………………….……..…6
DMX controlled operation………………………………………………………….…….…6
Addressing…………………………………………………………………………….…..…6
Control board………………………………………………………………………….…..…6
DMX protocol………………………………………………………………………….…..…7
TECHNICAL SPECIFICATIONS…………………………………………………….……7

2
Every person involved with installation. operation and maintenance of this fixture has to
- be qualified
- follow the instruction of this manual
- consider this manual to be part of the total product
- Keep this manual for the entire service life of the product
- pass this manual to every future owner or use of the product
INTRODUCTION
Thank you for choosing our fixture, if you follow up the instruction given in this manual we be sure that
you will enjoy this product for a long period of time
SAFETY INSTRUCTION
This device has left our premises in absolutely perfect condition .In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruction and
warning notes written in this user manual.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug
can be damaged leading to mortal electrical shock. If the power plug or the power switch is not
accessible, the device must be the disconnected via the mains. If the power plug or the device is dusty,
the device must be take out of operation, disconnected and then be cleaned with a dry cloth, Dust can
reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device
should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have exerted the device it must
immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the
device is still running, the device must be checking by a specialist if the liquid has reduced any
insulation. Reduced insulation can cause mortal electrical shock. There must never be any objects
entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse
metal chips enter into the device, the device must be taken out of operation and disconnected
CAUTION!
Be careful with your operations, With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires.
CAUTION !
Keep this device away from rain and moisture
Unplug mains lead before opening the housing
For your own safety, please read this user manual carefully before you initially start-up

3
immediately. Malfunction or short-circuits caused by metal parts my cause mortal injuries. Never look
directly into the light source, as sensitive persons may suffer an epileptic shock (especially meant for
epileptics)Keep away children and amateurs. Never leave this device running unattended.
OPERATING DETERMINATIONS
This device is designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects. Do not shake the device. Avoid brute force when
installing or operation the device. Never lift the fixture by holding it at the projector-head. As the
mechanics may be damaged. When choosing the installation-spot, please make sure that the device is
not exposed to extreme heat, moisture or dust. There should not be any cable lying around. Please
make sure that the fixture can not be touched or bumped. Your endanger your own and the safety of
others.
The maximum ambient temperature Ta=450C must never be exceeded. Operate the device only after
having become familiarized with its functions. Do not permit operation by persons not qualified for
operating the device. Most damages are the result of unprofessional operation. Please use the original
packaging if the device is to be transported. Please consider that unauthorized modifications on the
device are forbidden due to safety reasons! Never remove the serial barcode from the device as this
would make the guarantee void. If this device will be operated in any way different to the one described
in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any
other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
DESCRIPTION OF THE DEVICE
Features
> 3/4/5/10 channel DMX-512 .in optional
> Variable electronic strobe.
> Variable electronic dimmer (0-100%).and 4 type in optional
> LED operation menu with function buttons
> Reset to factory settings option. Color temperature setting
> Build-in program with speed adjustment
> 16 bit dimmer effect and White balance
> Temperature sensor via software to control fans speed against overheat
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating
working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but
instead use a professional structural rigger. Improper installation can result in bodily injury and or
damage to property. The projector had to be installed out of the reach of people

4
DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable
material(decoration articles, etc.)within a distance of min.0.5m.
DMX 512 connection/ connection between fixture
The wires must not come into contact with each other, otherwise the fixture will not work at all or
properly. Please note the starting address depends upon which controller is being used. Only use a
DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one
fixture to another
Connection with the mains.
The earth has to be connected. The device must only be connected with an electric installation carried
out in compliance with IEC standards.
OPERATION
After you connected the effect to the mains, The fixture starts running
Stand Alone operation
In the stand alone mode, the fixture can be use without controller
Master/slave-operation
The master/slave-operation enables that several devices can be synchronized and controlled by one
master-device
DMX controlled operation
You can control the projectors individually via your DMX-controller
Addressing
The control board allows you to assign the DMX starting address,
Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order
to ensure proper transmission on the DMX data link.
CONTROL BOARD
The control board offer several features :you can simple set the starting address, run the
pre-programmed program or make a reset

5
he main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by pressing
Up or Down .Press the Enter-button in order to select the desired menu. You can change the selection
by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave every
mode by pressing the Mode/Esc-button .The functions provided are described in the following setting.
MENU MAP
The device has two operation modes, It can be operated in Stand Alone or in DMX controlled
When in Master/Slave Synchronization Mode, only one 4 in 1 LED WASH in a series chain can be set
as the master.
STAT R.000 Adjust red color from 0~255
G.000 Adjust green color from 0~255
B.000 Adjust blue color from 0~255
ST.00 Adjust strobe effect from 0~20
AUTO AT From AT01 to AT10 with 10 different auto mode
PR From PR01 to PR10 with 10 different mode
SOUD MOD1 Sound control with color change
MOD2 Sound control with color strobe
RUN DMX and SLAV mode for selection
DMX Adjust DMX value from 001 to 512
PERS STRG Run static mode ,10 channel with details on dmx protocol
ARC.1 Run 3 channel mode Red/Green/Blue
AR1.D Run 4 channel mode Dimmer/Red/Green/Blue
AR1.5 Run 5 channel mode Dimmer/Red/Green/Blue/Strobe
HSV. Adjust Color in Hue (0~255),Saturation (0~255)and Value (0~255)
ID ID01 to ID66 to set different fixture
TEMP CURR show current fixture temperature
EDIT PR.01 to PR.10 to set 10 programmer
SC.01 to SC.30 to set 30 different sense
R.000 Adjust red color from 0~255
G.000 Adjust green color from 0~255
B.000 Adjust blue color from 0~255
ST.00 Adjust strobe effect from 0~20
T.000 Adjust from 0~255
F.000 Adjust from 0~255
SET UPLD sending data to next fixture with self-built in program
REST reset fixture
ID OFF/ON
RGB OFF/ON Adjust the correct color per RGB
POW HIGH/NORM select different power consumption with HIGH 100%
and Norm 33%
DIM OFF/DIM1/DIM2/DIM3/DIM4

6
CAL 1 White balance adjustment
WT01 to WT.11 to adjust R/G/B/W from 0~255
Ps:when run stat dmx mode, channel 6 can show 11 different white color
CAL 2 RGB adjust correct color for RGB
RGB adjust from 25~255
Note：output default setting address code is A001, pan is positive circumrotate、tilt is positive
circumrotate、LED positively reveal.
Master/slave mode(auto-running、sound control)
.This mode will allow you to link up 32 units together without a controller.
.Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of t
DMX-protocol
Channel Value Function
1
0-255 Dimmer 0-100% dimmer
2
0-255 Red 0-100% Red
3
0-255 Green 0-100% Green
4
0-255 Blue 0-100% Blue
5
0-5
6-20
21-30
31-255
Color Change
No function
Color change
No function
Color change in auto
6 0-10
11-255
Strobe
No function
Strobe with increasing speed
7
0-20
21-220
221-255
Built-in program
No function
Built in program 1-10
Sound control
8
0-255 Speed for built-in program Speed from slowly to fast
9
0-9
10-29
30-69
70-129
130-189
190-255
Dimmer Optional (1st channel Dimmer be open)
Dimmer speed
No function
Dimmer 1
Dimmer 2
Dimmer 3
Dimmer 4
10
ID selection (After select the fixture per ID1~ID66,
control via DMX when open value as below per

7
0-9
10-211
211-222
each model even they are at same dmx value )
No function
Each 10 value with a ID from ID1 until ID19
Each value with a ID from ID20 until ID66
TECHNICIAL SPECIFICATIONS
Model COBPAR100T
Voltage 110V- 250V / 50-60Hz
Power consumption: 120w
LED 100W RGB COB leds
Gross Weight 2.9Kgs
Dimensions 37 (H) x25(W) x25(L) mm
www.destilan-deutschland.de