involight LED MH368ZW User manual

Bedienungsanleitung
User manual
LED MH368ZW
www.destilan-deutschland.de

1
Table of contents
INTRODUCTION ……………………………………………….…………………………..2
SAFETY INSTRUCTIONS…………………………………………………………………2
OPERATING DETERMINATIONS…………………………………………….…………..3
DESCRIPTION OF THE DEVICE…………………………………………………………4
INSTALLATION………………………………………………………………….…………..5
OPERATION……………………………………………………………………….………...6
Stand alone operation…………………………………………………………….…………6
Master slave operation…………………………………………………………….……..…6
DMX controlled operation………………………………………………………….…….…6
Addressing…………………………………………………………………………….…..…6
Control board………………………………………………………………………….…..…6
DMX protocol………………………………………………………………………….…..…7
TECHNICAL SPECIFICATIONS…………………………………………………….……7

2
Every person involved with installation. operation and maintenance of this fixture has to
- be qualified
- follow the instruction of this manual
- consider this manual to be part of the total product
- Keep this manual for the entire service life of the product
- pass this manual to every future owner or use of the product
INTRODUCTION
Thank you for choosing our fixture, if you follow up the instruction given in this manual we be sure that
you will enjoy this product for a long period of time
SAFETY INSTRUCTION
This device has left our premises in absolutely perfect condition .In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruction and
warning notes written in this user manual.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution! Never touch them with wet hands .as this could lead
to mortal electrical shock. Never modify, bend, strain mechanically, put pressure on, pull or heat up the
power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages,
fire or mortal electrical shock. The cable insert or the female part in the device must never be strained.
There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may
lead to mortal electrical shock. Make sure that the power-cord is never crimped or damaged by sharp
edges. Check the device and the power-cord from time to time.If extension cords are used, make sure
that the core diameter is sufficient for the required power consumption of the device. All warnings
concerning the power cords are also valid for possible extension cords.
DESCRIPTION OF THE DEVICE
CAUTION!
Be careful with your operations, With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires.
CAUTION !
Keep this device away from rain and moisture
Unplug mains lead before opening the housing
For your own safety, please read this user manual carefully before you initially start-up

3
Features
> 14 channel DMX-512 .
> Pan :630°/tilt:270°.
> 36pcs 8W RGBW QUAD LED
> Zoom angle from 18 degree to 55 degree
> Variable electronic strobe.
> Variable electronic dimmer(0-100%).
> LED display menu with invert.
> Reset to factory settings option.
> Pan/tilt invert option.
> Fan cooled.
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating
working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but
instead use a professional structural rigger. Improper installation can result in bodily injury and or
damage to property. The projector had to be installed out of the reach of people
DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable
material(decoration articles, etc.)within a distance of min.0.5m.
DMX 512 connection/ connection between fixture
The wires must not come into contact with each other, otherwise the fixture will not work at all or
properly. Please note the starting address depends upon which controller is being used. Only use a
DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one
fixture to another
Connection with the mains.

4
The earth has to be connected. The device must only be connected with an electric installation carried
out in compliance with IEC standards.
OPERATION
After you connected the effect to the mains, The fixture starts running
Stand Alone operation
In the stand alone mode, the fixture can be use without controller
Master/slave-operation
The master/slave-operation enables that several devices can be synchronized and controlled by one
master-device
DMX controlled operation
You can control the projectors individually via your DMX-controller
Addressing
The control board allows you to assign the DMX starting address,
Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order
to ensure proper transmission on the DMX data link.
CONTROL BOARD
The control board offer several features :you can simple set the starting address, run the
pre-programmed program or make a reset
he main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by pressing
Up or Down .Press the Enter-button in order to select the desired menu. You can change the selection
by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave every
mode by pressing the Mode/Esc-button .The functions provided are described in the following setting.
MENU MAP
DMX512 DMX address set from 001-512
RUN MODE
DMX mode :14 channel AUTO mode: 8 different mode fromAuto 1 to Auto 8
SOUND mode: Sound control
TEST MODE PAN: Pan movement 0-255
TILT: Tilt movement 0-255
FOCUS: Zoom movment 0-255
RED:Red dimming 0-255(default 30)
GREEN:Green dimming 0-255(default 30)
BLUE:Blue dimming 0-255 (default 30)

5
WHITE: White dimming 0-255 (default 30)
LANGUAGE ENGLISH/CHINESE
SET UP ID CODE:select ID code
PAN REVERSE:ON/OFF
TILT REVERSE:ON/OFF
FADER DELAY:ON/OFF
SIGNAL LINK:ON/OFF
CODE WHEEL:ON/OFF
TEMPSWITCH SET:ON/OFF
TEMPERATURE SET:70degree
SCREEN SAVER:MODE1(Show dmx address after 10 seconds)
MODE2(Screen off after 10 seconds)
OFF()
DISPLAY REVERSE:ON/OFF
FACTORY SET:ON/OFF
RESET:ON/OFF
TOUCHCORRECT:ON/OFF
PANOFF SET:ON/OFF
TILT OFF SET:ON/OFF
SYSINFO ON TIME:current on time
RUN TIME:total run time
SOFTVER:software version
RUNNING MODE:current run mode
DMX ADDRESS:dmx address
TEMPERATURE:current temperature
DMX-protocol
14 DMX channel mode
Channel Value Function
1
0-255 Pan Pan movement 0~540
2
0-255 Tilt Tilt movement 0~270
3
0-255 Pan Tilt speed Pan & Tilt speed adjustment
4
0-255 Dimmer 0~100% dimmer
5
0-255 Red 0-100% Red
6
0-255 Green 0-100% Green
7
0-255 Blue 0-100% Blue
8
White

6
0-255 0-100% White
9
0-255 Zoom From 18 degree to 55 degree zoom
10 0
1-255
Strobe
No function
Strobe with increasing speed
11
0
1-20
21-40
41-60
61-80
81-100
101-120
121-140
141-160
161-170
171-200
201-205
206-210
211-215
216-220
221-215
226-230
231-235
236-240
241-245
246-250
251-255
Build in Color
Running this channel need channel 14 at 91-210
No function
R255 G↑B0 W0
R↓G255 B0 W0
R0 G255 B↑W0
R0 G↓B255 W0
R↑G0 B255 W0
R255 G0 B↓W0
R255 G↑B↑W0
R↓G↓B255 W0
R255 G255 B255 W255
R0 G0 B0 W0
R242 G204 B5 W227
R242 G215 B5 W227
R255 G255 B50 W255
R255 G255 B90 W255
R255 G255 B118 W255
R255 G255 B132 W255
R255 G255 B151 W255
R255 G255 B171 W255
R255 G255 B185 W255
R255 G255 B197 W255
R255 G255 B234 W255
12
0
1-25
26-50
51-90
91-130
131-170
171-210
211-250
251-255
Built in effect
Switch off ID effect
Fade delay open
Fade delay close
Select built color on
Color change in pulse
Color change
Color change in fade
Built in mode 1
Sound mode
13
0-255 Pan Fine Pan fine movement 0~540
14
0-255 Tilt Fine Pan fine movement 0~540

7
TECHNICIAL SPECIFICATIONS
Model LED MH368ZW
Voltage 110V- 250V / 50-60Hz
Power consumption: 380W
LED 36x8pcs RGBW QUAD
Gross Weight 9.5Kgs
Dimensions 420(H) x 300(W) x400(L) mm
www.destilan-deutschland.de