INVT Goodrive100-PV Series User manual

Solar Pumping VFD
Goodrive100-PV Series

Goodrive100-PV Series Solar Pumping VFD Contents
i
Contents
Contents ....................................................................................................................................i
1 Safety precautions ...............................................................................................................1
1.1 Safety definition .............................................................................................................1
1.2 Warning symbols ...........................................................................................................1
1.3 Safety guidelines ...........................................................................................................2
2 Product overview..................................................................................................................4
2.1 Unpacking inspection ....................................................................................................4
2.2 Name plate ....................................................................................................................4
2.3 Type designation key .....................................................................................................4
2.4 Product specifications....................................................................................................5
2.5 Rated specifications ......................................................................................................5
3 Installation guidelines..........................................................................................................7
3.1 Mechanical installation ..................................................................................................7
3.2 Standard wiring..............................................................................................................9
4 Keypad operation procedure ............................................................................................14
4.1 Keypad introduction .....................................................................................................14
4.2 Keypad displaying .......................................................................................................17
4.3 Keypad operation ........................................................................................................18
5 Commissioning guidelines................................................................................................20
5.1 Inspection before operation .........................................................................................20
5.2 Trial run........................................................................................................................20
5.3 Parameter settings ......................................................................................................20
5.4 Advanced settings .......................................................................................................20
6 Function parameters ..........................................................................................................22
6.1 Common function parameters for solar pumping control ............................................22
6.2 Parameters of special functions ..................................................................................41
7 Fault diagnosis and solution.............................................................................................59
Appendix A Options and use................................................................................................65
A.1 Boost module ..............................................................................................................65
A.2 GPRS module and monitoring APP ............................................................................66
A.3 Cables .........................................................................................................................67
A.4 Reactors ......................................................................................................................69
A.5 Filters...........................................................................................................................70
Appendix B Recommended solar modules ........................................................................71
B.1 Recommended configuration for solar pumping VFDs ...............................................71
B.2 Recommended configuration for VFDs with the boost module...................................72
Appendix C Power frequency & PV switching solution ....................................................73
C.1 Solution introduction ...................................................................................................73
C.2 IP54 protection-level VFDs .........................................................................................77
C.3 Wiring terminals ..........................................................................................................78
C.4 Parameter setting method...........................................................................................79
Appendix D Dimension drawings ........................................................................................80
D.1 External keypad structure ...........................................................................................80
D.2 Dimensions of 0.4-2.2kW models ...............................................................................81
D.3 Dimensions of 1.5-200kW models ..............................................................................83
Appendix E Further information ..........................................................................................86
E.1 Product and service inquiries ......................................................................................86

Goodrive100-PV Series Solar Pumping VFD Safety precautions
1
1 Safety precautions
Please read this manual carefully and follow all safety precautions before moving, installing,
operating and servicing the variable-frequency drive (VFD). If ignored, physical injury or death
may occur, or damage may occur to the devices.
If any physical injury or death or damage to the devices occurs for ignoring to the safety
precautions in the manual, our company will not be responsible for any damages and we are
not legally bound in any manner.
1.1 Safety definition
Danger:
Serious physical injury or even death may occur if not follow
relevant requirements
Warning:
Physical injury or damage to the devices may occur if not follow
relevant requirements
Note:
Physical hurt may occur if not follow relevant requirements
Qualified
electricians:
People working on the device should take part in professional
electrical and safety training, receive the certification and be
familiar with all steps and requirements of installing,
commissioning, operating and maintaining the device to avoid
any emergency.
1.2 Warning symbols
Warnings caution you about conditions which can result in serious injury or death and/or
damage to the equipment, and advice on how to avoid the danger. Following warning symbols
are used in this manual:
Symbols
Name
Instruction
Abbreviation
Danger
Danger
Serious physical injury or even
death may occur if not follow the
relative requirements
Warning
Warning
Physical injury or damage to the
devices may occur if not follow the
relative requirements
Do not
Electrostatic
discharge
Damage to the PCBA board may
occur if not follow the relative
requirements
Hot sides
Hot sides
Sides of the device may become
hot. Do not touch.
Note
Note
Physical hurt may occur if not follow
the relative requirements
Note

Goodrive100-PV Series Solar Pumping VFD Safety precautions
2
1.3 Safety guidelines
Only qualified electricians are allowed to operate on the VFD.
Do not carry out any wiring and inspection or changing components when
the power supply is applied. Ensure all input power supply is disconnected
before wiring and checking and always wait for at least the time designated
on the VFD or until the DC bus voltage is less than 36V. Below is the table
of the waiting time:
VFD model
Minimum waiting time
1PH 220V
0.4kW-2.2kW
5 minutes
3PH 220V
1.5kW-7.5kW
5 minutes
3PH 380V
0.75kW-110kW
5 minutes
3PH 380V
132kW-200kW
15 minutes
Do not refit the VFD unauthorized; otherwise fire, electric shock or other
injury may occur.
The base of the radiator may become hot during running. Do not touch to
avoid hurt.
The electrical parts and components inside the VFD are electrostatic. Take
measurements to avoid electrostatic discharge during relevant operation.
1.3.1 Delivery and installation
Please install the VFD on fire-retardant material and keep the VFD away
from combustible materials.
Do not operate on the VFD if there is any damage or components loss to
the VFD.
Do not touch the VFD with wet items or body, otherwise electric shock may
occur.
Note:
Select appropriate moving and installing tools to ensure a safe and normal running of the
VFD and avoid physical injury or death. For physical safety, the erector should take some
mechanical protective measurements, such as wearing safety shoes and working uniforms.
Do not carry the VFD by its cover. The cover may fall off.
Ensure to avoid physical shock or vibration during delivery and installation.
Install away from children and other public places.
The VFD cannot meet the requirements of low voltage protection in IEC61800-5-1 if the
altitude of installation site is above 2000m.
The leakage current of the VFD may be above 3.5mA during operation. Ground with proper
techniques and ensure the grounding resistor is less than 10Ω. The conductivity of PE
grounding conductor is the same as that of the phase conductor (with the same cross
sectional area).

Goodrive100-PV Series Solar Pumping VFD Safety precautions
3
(+) and (-) are DC power supply input terminals. R, S and T (L,N) are AC power supply
input terminals. U, V and W are output terminals. Please connect the input power cables
and motor cables with proper techniques; otherwise the damage to the VFD may occur.
1.3.2 Commissioning and running
Disconnect all power supplies applied to the VFD before the terminal
wiring and wait for at least the designated time after disconnecting the
power supply.
High voltage is present inside the VFD during running. Do not carry out
any operation except for the keypad setting.
The VFD cannot be used as “Emergency-stop device”.
If the VFD is used to break the motor suddenly, a mechanical braking
device should be provided.
Note:
Do not switch on or off the input power supply of the VFD frequently.
For VFDs that have been stored for a long time, check and fix the capacitance and try to
run it again before utilization.
Cover the front board before running, otherwise electric shock may occur.
1.3.3 Maintenance and replacement of components
Only qualified electricians are allowed to perform the maintenance,
inspection, and components replacement of the VFD.
Disconnect all power supplies to the VFD before the terminal wiring. Wait
for at least the time designated on the VFD after disconnection.
Take measures to avoid screws, cables and other conductive materials to
fall into the VFD during maintenance and component replacement.
Note:
Please select proper torque to tighten screws.
Keep the VFD, parts and components away from combustible materials during
maintenance and component replacement.
Do not carry out any isolation voltage-endurance test on the VFD and do not measure the
control circuit of the VFD by megameter.
1.3.4 Scrap treatment
There are heavy metals in the VFD. Deal with it as industrial effluent.
When the life cycle ends, the product should enter the recycling system.
Dispose of it separately at an appropriate collection point instead of
placing it in the normal waste stream.

Goodrive100-PV Series Solar Pumping VFD Product overview
4
2 Product overview
2.1 Unpacking inspection
Check as follows after receiving products:
1. Check that there are no damage and humidification to the package. If not, please
contact with local agents or offices.
2. Check the information on the type designation label on the outside of the package to
verify that the drive is of the correct type. If not, please contact with local dealers or offices.
3. Check that there are no signs of water in the package and no signs of damage or breach
to the VFD. If not, please contact with local dealers or offices.
4. Check the information on the type designation label on the outside of the package to
verify that the name plate is of the correct type. If not, please contact with local dealers or
offices.
5. Check to ensure the accessories (including user’s manual and control keypad) inside
the device is complete. If not, please contact with local dealers or offices.
2.2 Name plate
Figure 2-1 Name plate
Note: This is the example of Goodrive100-PV standard products and the CE\TUV\IP20
certifications are marked according to the reality.
2.3 Type designation key
The type designation contains information on the VFD. The user can find the type designation
on the type designation label attached to the VFD or the simple name plate.
GD100 –5R5G –4 5 –PV
① ② ④③ ⑤
I P2 0
S/N:
Model: GD100-2R2G-S2-PV
Power(Output): 2.2kW
Input: DC 150V-440V
AC 1PH 220V (-15%)-240V (+10%) 24A 47 Hz-63Hz
Output: AC 3PH 0V-Uinput 10A 0Hz-400Hz

Goodrive100-PV Series Solar Pumping VFD Product overview
5
Key
Sign
Description
Remarks
Product
abbreviation
①
Product
abbreviation
GD100 is short for Goodrive100.
Rated power
②
Power range
+ Load type
5R5G—5.5kW
G—Constant torque load
Voltage
degree
③
Voltage
degree
4: AC 3PH 380V (-15%)–440(+10%)
2: AC 3PH 220V (-15%)–240(+10%)
S2: AC 1PH 220V (-15%)–240(+10%)
SS2: AC 1PH input/output 220V (-15%)–
240(+10%)
Protection
level
④
Protection
level
Protection level.
5—IP54
The protection level of a standard VFD is
IP20, but this field is not displayed.
Industrial
code
⑤
Industrial
code
PV stands for solar pumping.
2.4 Product specifications
Model
-SS2
-S2
-2
-4
AC input voltage (V)
220 (-15%)–240 (+10%)
(1PH)
220
(-15%)–
240
(+10%)
(3PH)
380
(-15%)–
440
(+10%)
(3PH)
Max. DC voltage (V)
440
440
440
800
Start-up voltage (V)
200
200
200
300
Lowest working voltage (V)
150
150
150
250
Recommended DC input
voltage range (V)
200–400
200–400
200–400
300–750
Recommended MPP voltage
(V)
330
330
330
550
2.5 Rated specifications
Series
Model
Rated
output
power
(Kw)
Rated
input
current (A)
Rated output
current (A)
Max. DC input
current (A)
-SS2 model
1PH 220V
GD100-0R4G-SS2-PV
0.4
6.5
4.2
9
GD100-0R7G-SS2-PV
0.75
9.3
7.2
9

Goodrive100-PV Series Solar Pumping VFD Product overview
6
Series
Model
Rated
output
power
(Kw)
Rated
input
current (A)
Rated output
current (A)
Max. DC input
current (A)
Input/output
(0.4-2.2 kW)
GD100-1R5G-SS2-PV
1.5
15.7
10.2
12
GD100-2R2G-SS2-PV
2.2
24
14
12
-S2 model
1PH 220V
input
(0.4-2.2 kW)
GD100-0R4G-S2-PV
0.4
6.5
2.5
9
GD100-0R7G-S2-PV
0.75
9.3
4.2
9
GD100-1R5G-S2-PV
1.5
15.7
7.5
12
GD100-2R2G-S2-PV
2.2
24
10
12
-2 model
3PH 220V
(1.5-7.5kW)
GD100-1R5G-2-PV
1.5
7.7
7.5
12
GD100-2R2G-2-PV
2.2
11
10
12
GD100-004G-2-PV
4
17
16
20
GD100-5R5G-2-PV
5.5
25
20
30
GD100-7R5G-2-PV
7.5
33
30
40
-4 model
3PH 380V
(0.75-200kW)
GD100-0R7G-4-PV
0.75
3.4
2.5
9
GD100-1R5G-4-PV
1.5
5.0
4.2
9
GD100-2R2G-4-PV
2.2
5.8
5.5
12
GD100-004G-4-PV
4.0
13.5
9.5
16.5
GD100-5R5G-4-PV
5.5
19.5
14
23.9
GD100-7R5G-4-PV
7.5
25
18.5
30.6
GD100-011G-4-PV
11
32
25
39.2
GD100-015G-4-PV
15
40
32
49
GD100-018G-4-PV
18.5
47
38
50
GD100-022G-4-PV
22
51
45
60
GD100-030G-4-PV
30
70
60
81
GD100-037G-4-PV
37
80
75
90
GD100-045G-4-PV
45
98
92
130
GD100-055G-4-PV
55
128
115
150
GD100-075G-4-PV
75
139
150
200
GD100-090G-4-PV
90
168
180
250
GD100-110G-4-PV
110
201
215
300
GD100-132G-4-PV
132
265
260
360
GD100-160G-4-PV
160
310
305
430
GD100-185G-4-PV
185
345
340
500
GD100-200G-4-PV
200
385
380
550

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
7
3 Installation guidelines
The chapter describes the mechanical installation and electric installation.
Only qualified electricians are allowed to carry out what described in this
chapter. Please operate as the instructions in Safety precautions.
Ignoring these may cause physical injury or death or damage to the
devices.
Ensure the power supply of the VFD is disconnected during the operation.
Wait for at least the time designated after the disconnection if the power
supply is applied.
The installation and design of the VFD should be complied with the
requirement of the local laws and regulations in the installation site. If the
installation infringes the requirement, our company will exempt from any
responsibility. Additionally, if users do not comply with the suggestion,
some damage beyond the assured maintenance range may occur.
3.1 Mechanical installation
3.1.1 Installation environment
The installation environment is the safeguard for a full performance and long-term stable
functions of the VFD. Check the installation environment as follows:
Environment
Conditions
Installation site
Indoor
Environment
temperature
The ambient temperature of VFD is -10 ℃–50 ℃while air
temperature change should be less than 0.5℃per minute.
The VFD will be derated once ambient temperature exceeds 40℃. It
is not recommended to use the VFD if ambient temperature is above
50℃.
To ensure reliability, do not use the VFD if the ambient temperature
changes frequently.
Provide cooling fan or air conditioner to control the internal ambient
temperature below the required one if the VFD is used in a close
space such as in the control cabinet.
When the temperature is too low, if the VFD needs to restart to run
after a long stop, it is necessary to provide an external heating device
to increase the internal temperature, otherwise damage to the
devices may occur.
Humidity
RH≤90%. No condensation is allowed.
Storage
temperature
-40°C–+70°C. The temperature change rate is less than 1°C/minute.

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
8
Environment
Conditions
Running
environment
condition
The installation site of the VFD should:
Keep away from the electromagnetic radiation source;
Keep away from contaminative air, such as corrosive gas, oil mist and
flammable gas;
Ensure foreign objects, such as metal power, dust, oil, water cannot
enter into the VFD (do not install the VFD on the flammable materials
such as wood);
Keep away from direct sunlight, oil mist, steam, and vibration
environment.
Pollution
Pollution degree 2
Altitude
When the altitude exceeds 1000m but is lower than 3000m, derate
1% for every additional 100m;
When the altitude exceeds 2000m, configure an isolation transformer
on the input end of the VFD.
When the altitude exceeds 3000m but is lower than 5000m, contact
our company for technical consultation. Do not use the VFD at an
altitude higher than 5000m.
Vibration
≤ 5.8m/s2(0.6g)
Installation
direction
The VFD should be installed on an upright position to ensure
sufficient cooling effect.
Note:
Goodrive100-PV series VFDs should be installed in a clean and ventilated environment
according to enclosure classification.
Cooling air must be clean, free from corrosive materials and electrically conductive dust.
3.1.2 Installation direction
The VFD may be installed on the wall or in a cabinet.
The VFD needs be installed in the vertical position. Check the installation site according to the
requirements below. See Appendix D Dimension drawings for frame details.
3.1.3 Installation manner
(1) The VFDs ≤2.2kW support wall mounting and rail mounting.

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
9
a) Wall mounting b) Rail mounting
Figure 3-1 Installation manners
Note: The minimum space of A and B is 100mm. H is 36.6mm and W is 35.0mm.
(2) The VFDs ≥4kW support wall mounting and flange mounting.
Flange
Figure 3-2 Installation manners
1) Mark the locations of installation holes. For details about the holes, see the VFD dimension
diagram in the appendix.
2) Fix the screws or bolts into the marked locations.
3) Lean the VFD against the wall.
4) Fasten the tightening screws on the wall.
3.2 Standard wiring
3.2.1 Terminals of main circuit
The figure below shows the standard wiring of VFD.

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
10
Well
S2
S3
COM
GD100-PV
VFD
High water level switch
Low water level switch
Common terminal
Water
tower
S1
S4
COM
Forced switch to mains
1PH/2PH algorithm
shifting
Common terminal
(+) (-)
Q1
PV input
U V W
Water
pump
Figure 3-3 Standard wiring diagram
The DC breaker Q1 must be installed as the protection switch for PV input.
In parallel connection, the combination box special for PV must be used.
When the distance between the PV input component and VFD exceeds 10
meters, type-II surge protection devices must be configured at the DC
side.
When the distance between the pump and VFD exceeds 50 meters, it is
recommended to configure output reactors. See appendix A.4 for the
output reactor model selection.
The VFD automatically runs after being powered on. If parameters need to
be set, follow the parameter setting instructions in chapter 5.
Before connecting the braking resistor cable, remove the yellow labels of
PB, (+), and (-) from the terminal blocks. Otherwise, poor connection may
occur.

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
11
Terminal
Name
Function
R, S, T
(L, N)
AC input
3PH (1PH) AC input terminals, connected to the grid
Note: Use the screws equipped with the VFD for wiring.
(+), (-)
PV input
Solar cell panel input terminals
U, V, W
VFD output
3PH/1PH AC output terminals, connected to the pump
motor
Note: 1PH motors must connect to terminals U and W.
Safety
grounding
Safety protection grounding terminal. Each VFD must
be grounded
Description for -SS2 single-phase output models
1) Generally, the output terminals U and W of the VFD connect to the phase cables of the
single-phase motor.
2) If the single-phase pump cannot be started, the two-phase control method must be used,
and the start-up and running capacitors (if any) of the motor must be removed. The figure
below shows the internal wiring of the common single-phase motor. In the figure, L1, L2, C1,
and C2 indicate the running winding, start-up winding, running capacitor, and start-up
capacitor. When the motor speed exceeds 75% of the rated speed, the start-up capacitor is
switched off.
U1
U2
V2
V1
L
N
L1
L2
C1
C2
K
Internal wiring of the single-phase motor winding after removing the starting and running
capacitor:

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
12
U1
U2
V2
V1
L1
L2
C1
C2
W
U
V
U1
U2
V2
V1
L1
L2
L
N
K
U1 and V1 are the common terminals of the windings. Connect them to the output terminal W
of the solar pumping VFD. Connect U2 to the output terminal U of the VFD. Connect V2 to the
output terminal V of the VFD. (Note: Use the screws equipped with the VFD.) Connect S4 of
the VFD to COM in short circuited manner.
3.2.2 Terminals of control circuit
Functions of control terminals
Category
Terminal
symbol
Terminal name
Terminal function
Power supply
24V
24V power supply
It provides the power of
24V±10% and maximum
current of 200mA.
It functions as the working
power supply of digital input
and output or externally
connects to the sensor power
supply.
COM
Common terminal
Digital input
S1
Forced switch to
power frequency
Terminal feature parameters:
1. Internal impedance: 3.3kΩ
2. Acceptable voltage input:
12–24V
3. Maximum input frequency:
1kHz
S1: Forcible switch to power
frequency (Switching-on
indicates switching to power
S2
Full-water alarm
S3
Empty-water
alarm

Goodrive100-PV Series Solar Pumping VFD Installation guidelines
13
Category
Terminal
symbol
Terminal name
Terminal function
S4
Single/two phase
algorithm
switching
frequency, and switching-off
indicates input controlled by the
keypad.)
S2: It connects to the
high-water switch of the
normally open contact by
default.
S3: It connects to the
low-water switch of the
normally closed contact.
S4: A high electrical level
corresponds to the
single-phase algorithm. A low
electrical level corresponds to
the two-phase algorithm.
Communication
RS485+
RS485-
485
communication
485 communication terminals,
using the Modbus protocol
422TX+
422TX-
422RX+
422RX-
422
communication
Communication terminals
special for the boost module.
Relay output
RO1A
(ROA)
Normally open
contact of relay 1
1. Contact capacity:
3A/AC250V, 1A/DC30V
2. They cannot be used for
high frequency switch output.
During the application of auto
power frequency & PV
switching, the AC input
contactor coil is controlled by
the normally closed contact of
the relay.
RO1B
(ROB)
Normally closed
contact of relay 1
RO1C
(ROC)
Common terminal
of relay 1

Goodrive100-PV Series Solar Pumping VFD Keypad operation procedure
14
4 Keypad operation procedure
4.1 Keypad introduction
Keypads are used to control GD100-PV series VFDs, read the state data and adjust
parameters. If it is necessary to connect the keypad to other external device, you can use the
standard RJ45 cable with crystal head as the external extension cable.
Figure 4-1 Keypad diagram for VFDs ≤2.2kW
1
2
4
3
PRG
ESC
DATA
QUICK
JOG SHIFT
RUN STOP
RST
RUN/TUNE FWD/REV LOCAL/REMOT TRIP
HZ
A
V
RPM
%
Figure 4-2 Keypad diagram for VFDs ≥4kW
Note: External keypads can be configured for VFDs ≤2.2kW. The keypads of VFDs ≥4kW
can be used as external keypads.

Goodrive100-PV Series Solar Pumping VFD Keypad operation procedure
15
Serial
No.
Name
Description
1
State
LED
RUN/TUNE
LED off means that the VFD is in the
stopping state; LED blinking means the
VFD is in the parameter autotune state;
LED on means the VFD is in the running
state.
FWD/REV
FED/REV LED
LED off means the VFD is in the forward
rotation state; LED on means the VFD is
in the reverse rotation state.
LOCAL/REMOT
LED for keypad operation, terminals
operation and remote communication
control
LED off means that the VFD is in the
keypad operation state; LED blinking
means the VFD is in the terminals
operation state; LED on means the VFD
is in the remote communication control
state.
TRIP
LED for faults
LED on when the VFD is in the fault state;
LED off in normal state; LED blinking
means the VFD is in the pre-alarm state.
2
Unit
LED
Mean the unit displayed currently
Hz
Frequency unit
RPM
Rotating speed unit
A
Current unit
％
Percentage
V
Voltage unit
3
Display
zone
5-figure LED display displays various monitoring data and alarm code such
as set frequency and output frequency.

Goodrive100-PV Series Solar Pumping VFD Keypad operation procedure
16
Serial
No.
Name
Description
Display
Mean
Display
Mean
Display
Mean
Display
Mean
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
H
I
L
N
n
o
P
r
S
t
U
v
.
-
4
Buttons
PRG
ESC
Programming
key
Enter or escape from the first level menu
and remove the parameter quickly.
DATA
ENT
Entry key
Enter the menu step-by-step.
Confirm parameters.
UP key
Increase data or function code
progressively.
DOWN key
Decrease data or function code
progressively
SHIFT
Right-shift key
Move right to select the displaying
parameter circularly in stopping and
running mode.
Select the parameter modifying digit
during the parameter modification.
RUN
Run key
This key is used to operate on the VFD in
key operation mode.
STOP
RST
Stop/
Reset key
This key is used to stop in running state
and it is limited by function code P07.04.
This key is used to reset all control
modes in the fault alarm state.
QUICK
JOG
Quick key
The function of this key is confirmed by
function code P07.02.
5
Keypad
port
External keypad port. When keypads are valid, both the local and external
keypad LEDs are on.

Goodrive100-PV Series Solar Pumping VFD Keypad operation procedure
17
4.2 Keypad displaying
The keypad displaying state of GD100-PV series VFDs is divided into stopping state
parameter, running state parameter, function code parameter editing state and fault alarm
state and so on.
4.2.1 Displayed state of stopping parameters
When the VFD is in the stopping state, the keypad will display stopping parameters as shown
in figure 4-2.
In the stopping state, various kinds of parameters can be displayed. Select the parameters to
be displayed or not by P07.07. See the instructions of P07.07 for the detailed definition of each
bit.
In the stopping state, there are 4 parameters that can be displayed. They are: set frequency,
bus voltage, input terminals state, and output terminals state.
》/SHIFT can shift the parameters from left to right. QUICK/JOG (P07.02=2) can shift the
parameters from right to left.
4.2.2 Displayed state of running parameters
After the VFD receives valid running commands, the VFD will enter into the running state and
the keypad will display the running parameters. RUN/TUNE LED on the keypad is on, while
the FWD/REV is determined by the current running direction which is as shown in figure 4-2.
In the running state, there are 6 parameters that can be displayed. They are: running
frequency, set frequency, bus voltage, output voltage, output current, and rotating speed. 》
/SHIFT can shift the parameters from left to right. QUICK/JOG (P07.02=2) can shift the
parameters from right to left.
4.2.3 Displayed state of faults
If the VFD detects the fault signal, it will enter into the fault pre-alarm displaying state. The
keypad will display the fault code by flicking. The TRIP LED on the keypad is on, and the fault
reset can be operated by the STOP/RST on the keypad, control terminals or communication
commands.
4.2.4 Displayed state of function codes editing
In the state of stopping, running or fault, press PRG/ESC to enter into the editing state (if there
is a password, see P07.00). The editing state is displayed on two classes of menu, and the
order is: function code group/function code number →function code parameter, press
DATA/ENT into the displayed state of function parameter. On this state, press DATA/ENT to
save the parameters or press PRG/ESC to escape.

Goodrive100-PV Series Solar Pumping VFD Keypad operation procedure
18
RUN/TUNE FWD/REV LOCAL/REMOT
Hz
TRIP
A
V
RPM
%
RUN/TUNE FWD/REV LOCAL/REMOT TRIP
Hz
A
V
RUN/TUNE FWD/REV LOCAL/REMOT TRIP
Hz
A
V
RPM
%
RPM
%
Figure 4-3 Displayed state
4.3 Keypad operation
Operate the VFD via operation panel. See the detailed structure description of function codes
in the brief diagram of function codes.
4.3.1 How to modify the function codes of the VFD
The VFD has three levels menu, which are:
1. Group number of function code (first-level menu)
2. Tab of function code (second-level menu)
3. Set value of function code (third-level menu)
Remarks: Press both the PRG/ESC and the DATA/ENT can return to the second-level menu
from the third-level menu. The difference is: pressing DATA/ENT will save the set parameters
into the control panel, and then return to the second-level menu with shifting to the next
function code automatically; while pressing PRG/ESC will directly return to the second-level
menu without saving the parameters, and keep staying at the current function code.
Under the third-level menu, if the parameter has no flickering bit, it means the function code
cannot be modified. The possible reasons could be:
1) This function code is not modifiable parameter, such as actual detected parameter,
operation records and so on;
2) This function code is not modifiable in running state, but modifiable in stop state.
Example: Set function code P00.01 from 0 to 1.
The units place is
blinking
All digits are
blinking
Note: When setting the value, you can press and to modify the value.
+
PRG
ESC
PRG
ESC
PRG
ESC
PRG
ESC
DATA
ENT
DATA
ENT
DATA
ENT
The units place is
blinking
The units place is blinking
Figure 4-4 Sketch map of modifying parameters