INVT Goodrive20-EU VFD Series User manual

Goodrive20-EU series VFD Contents
i
Contents
Contents....................................................................................................................................i
1 Safety precautions ...............................................................................................................1
1.1 Safety definition.............................................................................................................1
1.2 Warning symbols ...........................................................................................................1
1.3 Safety guide...................................................................................................................2
1.3.1 Delivery and installation........................................................................................2
1.3.2 Commissioning and running .................................................................................3
1.3.3 Maintenance and component replacement ..........................................................3
1.3.4 What to do after scrapping....................................................................................3
2 Product overview..................................................................................................................4
2.1 Precautions for quick application...................................................................................4
2.1.1 Unpacking inspection............................................................................................4
2.1.2 Application confirmation........................................................................................4
2.1.3 Environment confirmation.....................................................................................4
2.1.4 Installation confirmation........................................................................................5
2.1.5 Basic commissioning............................................................................................5
2.2 Data related to safety standards....................................................................................6
2.3 Decommissioning ..........................................................................................................6
2.4 Product specifications....................................................................................................6
2.5 Name plate ....................................................................................................................9
2.6 Type designation key...................................................................................................10
2.7 Rated specifications ....................................................................................................10
2.8 Structure diagram........................................................................................................11
3 Installation guide................................................................................................................14
3.1 Mechanical installation ................................................................................................14
3.1.1 Installation environment......................................................................................14
3.1.2 Installation direction............................................................................................15
3.1.3 Installation mode.................................................................................................15
3.2 Standard wiring............................................................................................................17
3.2.1 Connection diagram of main circuit ....................................................................17
3.2.2 Terminals figure of main circuit...........................................................................18
3.2.3 Wiring of terminals in main circuit.......................................................................19
3.2.4 Wiring diagram of control circuit .........................................................................19
3.2.5 Terminals of control circuit..................................................................................19
3.2.6 Input/output signal connection figure..................................................................21
3.3 Overview of STO function............................................................................................23
3.3.1 Logic table for STO function...............................................................................23
3.3.2 Description of STO channel delay......................................................................23
3.3.3 Self-inspection on STO installation.....................................................................24
3.4 Layout protection.........................................................................................................24
3.4.1 Protecting the VFD and input power cable in short-circuit situations .................24
3.4.2 Protecting the motor and motor cables...............................................................25

Goodrive20-EU series VFD Contents
ii
3.4.3 Implementing a bypass connection ....................................................................25
4 Keypad operation procedure ............................................................................................26
4.1 Keypad introduction.....................................................................................................26
4.2 Keypad displaying .......................................................................................................29
4.2.1 Displayed state of stopping parameter...............................................................29
4.2.2 Displayed state of running parameters...............................................................29
4.2.3 Displayed state of fault .......................................................................................29
4.2.4 Displayed state of function codes editing ...........................................................30
4.3 Keypad operation ........................................................................................................30
4.3.1 How to modify the function codes of the VFD ....................................................30
4.3.2 How to set the password of the VFD..................................................................31
4.3.3 How to watch the VFD state through function codes..........................................31
5 Function parameters..........................................................................................................32
6 Fault tracking....................................................................................................................101
6.1 Maintenance intervals................................................................................................101
6.1.1 Cooling fan........................................................................................................103
6.1.2 Capacitors.........................................................................................................105
6.1.3 Power cable......................................................................................................105
6.2 Fault solution .............................................................................................................106
6.2.1 Alarm and fault indications................................................................................106
6.2.2 How to reset......................................................................................................106
6.2.3 Fault instruction and solution............................................................................106
6.2.4 Other states ......................................................................................................112
7 Communication protocol.................................................................................................113
7.1 Brief instruction to Modbus protocol ..........................................................................113
7.2 Application of the VFD...............................................................................................113
7.2.1 Two-wire RS485................................................................................................113
7.2.2 RTU mode.........................................................................................................116
7.2.3 ASCII mode.......................................................................................................119
7.3 Command code and communication data illustration................................................120
7.3.1 RTU mode.........................................................................................................120
7.3.2 ASCII mode.......................................................................................................124
7.4 Definition of data address..........................................................................................127
7.4.1 Rules of parameter address of the function codes...........................................128
7.4.2 Address instruction of other function in Modbus...............................................128
7.4.3 Fieldbus ratio values.........................................................................................132
7.4.4 Fault message response ..................................................................................133
7.5 Example of writing and reading .................................................................................134
7.5.1 Example of reading command 03H ..................................................................135
7.5.2 Example of writing command 06H....................................................................135
7.5.3 Example of continuous writing command 10H .................................................137
7.6 Common communication fault...................................................................................139
Appendix A Technical data .................................................................................................140
A.1 Ratings......................................................................................................................140
A.1.1 Capacity............................................................................................................140

Goodrive20-EU series VFD Contents
iii
A.1.2 Derating............................................................................................................140
A.2 CE .............................................................................................................................141
A.2.1 CE marking.......................................................................................................141
A.2.2 Compliance with the European EMC Directive ................................................141
A.3 EMC regulations........................................................................................................141
A.3.1 Category C2 .....................................................................................................142
A.3.2 Category C3 .....................................................................................................142
Appendix B Dimension drawings ......................................................................................143
B.1 External keypad structure .........................................................................................143
B.2 VFD chart..................................................................................................................145
Appendix C Peripheral options and parts.........................................................................150
C.1 Peripheral wiring .......................................................................................................150
C.2 Power supply ............................................................................................................151
C.3 Cables.......................................................................................................................151
C.3.1 Power cables....................................................................................................151
C.3.2 Control cables ..................................................................................................152
C.4 Breaker and electromagnetic contactor....................................................................153
C.5 Reactors....................................................................................................................154
C.6 Filter..........................................................................................................................156
C.6.1 C3 Filter type instruction ..................................................................................156
C.6.2 C3 filter.............................................................................................................156
C.6.3 Installation instruction for C3 filter....................................................................158
C.6.4 C2 Filter type instruction ..................................................................................158
C.6.5 C2 filter.............................................................................................................159
C.7 Brake components....................................................................................................159
C.7.1 Select the brake components...........................................................................159
C.7.2 Placing the brake resistor.................................................................................161
Appendix D Further information ........................................................................................163
D.1 Product and service inquiry.......................................................................................163
D.2 Feedback of INVT VFD manuals ..............................................................................163
D.3 Document library on the Internet...............................................................................163

Goodrive20-EU series VFD Safety precautions
1
1 Safety precautions
Please read this manual carefully and follow all safety precautions before moving, installing,
operating and servicing the VFD. If ignored, physical injury or death may occur, or damage
may occur to the devices.
If any physical injury or death or damage to the devices occurs due to neglect of the safety
precautions in the manual, our company will not be responsible for any damages and we are
not legally bound in any manner.
1.1 Safety definition
Danger:
Serious physical injury or even death may occur if related
requirements are not followed
Warning:
Physical injury or damage to the devices may occur if related
requirements are not followed
Note:
Physical hurt may occur if related requirements are not followed
Qualified
electricians:
People working on the device should take part in professional
electrical and safety training, receive the certification and be
familiar with all steps and requirements of installing,
commissioning, operating and maintaining the device to avoid
any emergency.
1.2 Warning symbols
Warnings caution you about conditions which can result in serious injury or death and/or
damage to the equipment, and advice on how to avoid the danger. Following warning symbols
are used in this manual:
Symbols
Name
Instruction
Abbreviation
Danger
Danger
Serious physical injury or even
death may occur if related
requirements are not followed
Warning
Warning
Physical injury or damage to the
devices may occur if related
requirements are not followed
No touch
Electrostatic
discharge
Damage to the PCBA board may
occur if related requirements are
not followed
Hot sides
Hot sides
Sides of the device may become
hot. Do not touch.
Note
Note
Physical hurt may occur if related
requirements are not followed
Note

Goodrive20-EU series VFD Safety precautions
2
1.3 Safety guide
Only qualified electricians are allowed to operate on the VFD.
Do not carry out any wiring, inspection or component replacement when
the power supply is applied. Ensure all input power supply is
disconnected before wiring and checking and always wait for at least the
time designated on the VFD or until the DC bus voltage is less than 36V.
The table below describes the waiting time:
VFD model Minimum waiting time
1PH 230V 0.4kW–2.2kW 5 minutes
3PH 230V 0.4kW–7.5kW 5 minutes
3PH 400V 0.75kW–110kW 5 minutes
Do not refit the VFD unless authorized; otherwise, fire, electric shock or
other injury may occur.
The base of the radiator may become hot during running. Do not touch to
avoid hurt.
The electrical parts and components inside the VFD are electrostatic.
Take measurements to avoid electrostatic discharge during related
operation.
1.3.1 Delivery and installation
Please install the VFD on fire-retardant material and keep the VFD away
from combustible materials.
Connect the optional brake parts (brake resistors, brake units or
feedback units) according to the wiring diagram.
Do not operate on the VFD if there is any damage or components loss to
the VFD.
Do not touch the VFD with wet items or body; otherwise, electric shock
may occur.
Note:
Select appropriate moving and installing tools to ensure a safe and normal running of the
VFD and avoid physical injury or death. For physical safety, the erector should take some
mechanical protective measurements, such as wearing exposure shoes and working
uniforms.
Ensure to avoid physical shock or vibration during delivery and installation.
Do not carry the VFD by its cover. The cover may fall off.
Install away from children and other public places.
The VFD cannot meet the requirements of low voltage protection in IEC61800-5-1 if the
altitude of installation site is above 2000m.
The leakage current of the VFD may be above 3.5mAduring operation. Ground properly
and ensure the grounding resistor is less than 10Ω. The conductivity of PE grounding
conductor is the same as that of the phase conductor (with the same cross sectional area).

Goodrive20-EU series VFD Safety precautions
3
R, S and T are the input terminals of the power supply, while U, V and W are the motor
terminals. Please connect the input power cables and motor cables properly; otherwise, the
damage to the VFD may occur.
1.3.2 Commissioning and running
Disconnect all power supplies applied to the VFD before the terminal
wiring and wait for at least the designated time after disconnecting the
power supply.
High voltage is present inside the VFD during running. Do not carry out any
operation except for the keypad setting.
The VFD may start up by itself when P01.21=1. Do not get close to the
VFD and motor.
The VFD cannot be used as "Emergency-stop device".
The VFD cannot be used to brake the motor suddenly.A mechanical brake
device should be provided.
Note:
Do not switch on or off the input power supply of the VFD frequently.
For VFDs that have been stored for a long time, set the capacitance and carry out
inspection and pilot run on the VFD before use.
Close the front cover before running; otherwise, electric shock may occur.
1.3.3 Maintenance and component replacement
Only well-trained and qualified professionals are allowed to carry out
maintenance, inspection, and component replacement on the VFD.
Disconnect all the power sources applied to the VFD before terminal
wiring, and wait for at least the time designated on the VFD after
disconnecting the power sources.
Take measures to prevent screws, cables and other conductive matters
from falling into the VFD during maintenance and component
replacement.
Note:
Select proper torque to tighten screws.
Keep the VFD and its parts and components away from combustible materials during
maintenance and component replacement.
Do not carry out insulation voltage-endurance test on the VFD, or measure the control
circuits of the VFD with megameters.
1.3.4 What to do after scrapping
The heavy metals inside the VFD should be treated as industrial effluent.
When the life cycle ends, the product should enter the recycling system.
Dispose of it separately at an appropriate collection point instead of
placing it in the normal waste stream.

Goodrive20-EU series VFD Product overview
4
2 Product overview
2.1 Precautions for quick application
2.1.1 Unpacking inspection
Check the following items after receiving the product.
1. Whether the packing box is damaged or dampened.
2. Whether the model identifier on the exterior surface of the packing box is consistent
with the purchased model.
3. Whether the interior surface of the packing box is abnormal, for example, in wet
condition, or whether the enclosure of the product is damaged or cracked.
4. Whether the nameplate of the product is consistent with the model identifier on the
exterior surface of the packing box.
5. Whether the accessories (including the user manual and control keypad) inside the
packing box are complete.
If any of the problems described in the check items are found, contact the local dealer or our
company.
2.1.2 Application confirmation
Confirm the following items before using the VFD.
1. Mechanical type of the load to be driven by the VFD. Check whether the VFD will be
overloaded in actual operation and whether the power level needs to be raised.
2. Whether the actual running current of the to-be-loaded motor is lower than the rated
current of the VFD.
3. Whether control precision implemented by the VFD meets the requirement of the actual
load.
4. Whether the grid voltage is consistent with the rated voltage of the VFD.
2.1.3 Environment confirmation
Check the following items before you install and use the VFD.
1. Whether the ambient temperature in the application is higher than 40°C. If yes, derate
the machine by 1% for every increased 1°C. Do not use the VFD in environments
where the temperature is higher than 50°C.
2. Note: If the VFD is installed in a cabinet, the ambient temperature is the air temperature
inside the cabinet.
3. Whether the ambient temperature in application is lower than –10°C. If yes, configure a
heating device.
4. Note: If the VFD is installed in a cabinet, the ambient temperature is the air temperature
inside the cabinet.

Goodrive20-EU series VFD Product overview
5
5. Whether the altitude on the site is higher than 1000 m. If yes, derate the machine by 1%
for every increased 100 m.
6. Whether the ambient humidity is higher than 90% or condensation occurs. If yes, take
extra protective measures.
7. Whether there is direct sunlight or biological invasion in the application environment. If
yes, take extra protective measures.
8. Whether there is dust or inflammable and explosive gas in the application environment.
If yes, take extra protective measures.
2.1.4 Installation confirmation
Check the following items after the installation of the VFD is complete.
1. Whether the input power cables and motor cables meet the current-carrying capacity
requirements of the actual load.
2. Whether the peripheral accessories are correctly selected and properly installed, and
whether the installation cables meet the current-carrying capacity requirements of the
accessories, including the input reactor, input filter, output reactor, output filter, DC
reactor, brake unit, and brake resistor.
3. Whether the VFD is installed on non-flammable materials, and whether its heat-emitting
accessories (such as reactor and brake resistor) are kept away from inflammable
materials.
4. Whether all the control cables are wired separately from power cables, and whether
electromagnetic compatibility (EMC) specification requirements are taken into full
account during the wiring.
5. Whether all the grounding systems are properly grounded according to the
requirements of the VFD.
6. Whether all the installation spacings of the VFD meet the requirements stated in the
manual.
7. Whether the installation of the VFD meets the requirements stated in the manual.
8. Check that the external connection terminals are tightly fastened and whether the
torque meets the requirements.
9. Whether screws, cables, or other conductive items drop into the VFD. If yes, take them
out.
2.1.5 Basic commissioning
Complete the basic commissioning as follows before using the VFD.
1. Perform autotuning if required. Remove the motor load, if possible, to perform dynamic
parameter autotuning; and if the load cannot be removed, you can perform static
autotuning.
2. Adjust the ACC/DEC time according to the actual operation conditions of the load.

Goodrive20-EU series VFD Product overview
6
3. Perform commissioning on the machine in jogging mode and check whether the
rotating direction of the motor meets the requirement. If no, exchange the wires of any
two phases of the motor to change the running direction of the motor.
4. Set all control parameters and then run the machine.
2.2 Data related to safety standards
IEC/EN 61058 (type A system)
ISO 13849**
SIL
PFH
HFT
SFF
λdu
λdd
PTI*
PL
CCF
MTTFd
DC
Category
2
8.73*10-10
1
71.23%
1.79*10-9
0
1 year
d
57
343.76
year
60%
3
3
8.53*10-10
1
99.38%
0.64*10-10 3.3*10-9
3
months
e
57
207.04
year
98.09%
3
* PTI: proof test interval
** According to the categorization defined in EN ISO 13849-1:2015.
2.3 Decommissioning
Before decommissioning any safety system from active service:
•Evaluate the impact of decommissioning on adjacent operating units and facilities or
other field services.
•Conduct a proper review and obtain required authorization.
•Ensure that the safety functions remain appropriate during decommissioning activities.
•Implement appropriate change management procedures for all decommissioning
activities.
2.4 Product specifications
Function
Specification
Power input
Input voltage (V)
AC 1PH 200V–240V, rated voltage: 230V
AC 3PH 200V–240V, rated voltage: 230V
AC 3PH 380V–480V, rated voltage: 400V
Allowable voltage
fluctuation
-15% –+10%

Goodrive20-EU series VFD Product overview
7
Function
Specification
Input current (A)
Refer to section 2.7 "Rated specifications".
Input frequency (Hz)
50Hz or 60Hz; allowed range: 47 –63Hz
Power output
Output voltage (V)
0 –input voltage
Output current (A)
Refer to section 2.7 "Rated specifications".
Output power (kW)
Refer to section 2.7 "Rated specifications".
Output frequency (Hz)
0 –400Hz
Technical
control
feature
Control mode
SVPWM, SVC
Motor
Asynchronous motor
Adjustable-speed ratio
Asynchronous motor 1:100 (SVC)
Speed control accuracy
±0.2% (SVC)
Speed fluctuation
±0.3% (SVC)
Torque response
<20ms (SVC)
Torque control accuracy
10%
Starting torque
0. 5Hz/150% (SVC)
Overload capability
150% of rated current: 1 minute
180% of rated current: 10 seconds
200% of rated current: 1 second
Running
control
feature
Frequency setting
method
Digital setting, analog setting, pulse frequency
setting, multi-step speed running setting, simple
PLC setting, PID setting, MODBUS communication
setting
Shift between the set combination and set channel.
Auto-adjustment of the
voltage
Keep a stable voltage automatically when the grid
voltage transients
Fault protection
Provide comprehensive fault protection functions:
overcurrent, overvoltage, undervoltage,
overheating, phase loss and overload, etc.
Start after speed tracking
Smoothing starting for running motor
Peripheral
interface
Analog input
1 (AI2) 0 –10V/0 –20mA and 1 (AI3) -10 –10V
Analog output
2 (AO1, AO2) 0 –10V/0 –20mA.
* AO2 output only available on GD20-EU >2.2kW
Digital input
4 common inputs, the max. frequency: 1kHz;
1 high speed input, the max. frequency: 50kHz
Digital output
1 Y1 terminal output
Relay output
2 programmable relay outputs
RO1A NO, RO1B NC, RO1C common terminal
RO2A NO, RO2B NC, RO2C common terminal

Goodrive20-EU series VFD Product overview
8
Function
Specification
Contact capacity: 3A/AC250V
*Relay 2 output only available on GD20-EU > 2.2kW
Others
DC reactor
Standard embedded DC reactor for the VFDs
(≥18.5kW)
Installation mode
Wall and rail installation of the VFDs (single phase
230V/three phase 400V, ≤2.2KW and three phase
230V, ≤0.75KW)
Wall and flange installation of the VFDs (three
phase 400V, ≥4KW and three phase 230V, ≥1.5KW)
Brake unit
Standard for the VFDs≤37kW and optional for the
VFDs within 45 –110kW
EMI filter
3PH 400V 4kW and above/3PH 230V 1.5kW and
above can comply with IEC61800-3 class C3,
others can meet requirements of IEC61800-3 class
C3 by installing external filter (optional). This series
of products can comply with IEC61800-3 class C2
by installing external filter (optional).
Ambient temperature
-10 to 50°C , derate 1% for every increased 1°C
when the temperature is higher than 40°C
Altitude
Below 1000m. If the elevation is above 1000m,
derate 1% for every additional 100m.
Ingress protection (IP)
rating
IP20
Note: The VFD with plastic casing should be
installed in metal distribution cabinet which
conforms to IP20 and the top of which conforms to
IP3X.
Pollution level
Level 2
Safety regulation
Comply with CE requirements
Cooling
Air cooling

Goodrive20-EU series VFD Product overview
9
2.5 Name plate
Figure 2-1 Name plate
Note: These are name plate examples for the standard products. The mark such as
CE/TUV/IP20/UL will be applied according to the actual condition. The 1PH/3PH 220V models
of 2.2kW and lower and the 3PH 380V models of 11kW and lower have been UL certified.
Model: GD20-1R5G-S2-EU
Power(Output): 1.5kW
Input: AC 1PH 200V-240V 15.7A 47Hz-63Hz
Output: AC 3PH 0V-Uinput 7.5A 0Hz-400Hz
S/N:
Model: GD20-015G-4-EU
Power(Output): 15kW
Input: AC 3PH 380V-480V 40A 47Hz-63Hz
Output: AC 3PH 0V-Uinput 32A 0Hz-400Hz
S/N:

Goodrive20-EU series VFD Product overview
10
2.6 Type designation key
The type designation contains information on the VFD. Users can find the type designation on
the type designation label attached to the VFD or the name plate.
GD20 –2R2G –4 –B –EU
①②③④⑤
Figure 2-2 Product type
Key
No.
Description
Detailed description
Product
abbreviation
①
Abbreviation for
product series
GD20: GD20 is short for Goodrive20
Rated power
②
Power range +
load type
055: 55kW;
G —Constant torque load
Voltage degree
③
Voltage degree
S2: 1PH 200V –240V
2: 3PH 200V –240V
4. 3PH 380V –480V
Additional remark 1
④
Built-in brake
unit
Null: Built-in brake unit is included in standard
configuration for models ≤ 37kW
-B
Built-in brake unit is optional for models ≥
45kW, -B is its built-in brake unit model
Additional remark 2
⑤
EU: Built-in safe torque off function
2.7 Rated specifications
Model
Voltage
degree
Rated output
power (kW)
Rated input
current (A)
Rated output
current (A)
STO
function
GD20-0R4G-S2-EU
Single
phase 230V
0.4
6.5
2.5
Class SIL2
PLd CAT.3
GD20-0R7G-S2-EU
0.75
9.3
4.2
GD20-1R5G-S2-EU
1.5
15.7
7.5
GD20-2R2G-S2-EU
2.2
24
10
GD20-0R4G-2-EU
Three phase
230V
0.4
3.7
2.5
GD20-0R7G-2-EU
0.75
5
4.2
GD20-1R5G-2-EU
1.5
7.7
7.5
Class SIL3
PLe CAT.3
GD20-2R2G-2-EU
2.2
11
10
GD20-004G-2-EU
4
17
16
GD20-5R5G-2-EU
5.5
21
20
GD20-7R5G-2-EU
7.5
31
30

Goodrive20-EU series VFD Product overview
11
Model
Voltage
degree
Rated output
power (kW)
Rated input
current (A)
Rated output
current (A)
STO
function
GD20-0R7G-4-EU
Three phase
400V
0.75
3.4
2.5
Class SIL2
PLd CAT.3
GD20-1R5G-4-EU
1.5
5.0
4.2
GD20-2R2G-4-EU
2.2
5.8
5.5
GD20-004G-4-EU
4
13.5
9.5
Class SIL3
PLe CAT.3
GD20-5R5G-4-EU
5.5
19.5
14
GD20-7R5G-4-EU
7.5
25
18.5
GD20-011G-4-EU
11
32
25
GD20-015G-4-EU
15
40
32
GD20-018G-4-EU
18.5
47
38
GD20-022G-4-EU
22
51
45
GD20-030G-4-EU
30
70
60
GD20-037G-4-EU
37
80
75
GD20-045G-4-EU
45
98
92
GD20-045G-4-B-EU
45
98
92
GD20-055G-4-EU
55
128
115
GD20-055G-4-B-EU
55
128
115
GD20-075G-4-EU
75
139
150
GD20-075G-4-B-EU
75
139
150
GD20-090G-4-EU
90
168
180
GD20-090G-4-B-EU
90
168
180
GD20-110G-4-EU
110
201
215
GD20-110G-4-B-EU
110
201
215
2.8 Structure diagram
Below is the layout figure of the VFD (Three phase 400V, ≤2.2kW) (take the VFD of 0.75kW as
the example).

Goodrive20-EU series VFD Product overview
12
Figure 2-3 Product structure (3PH 400V, ≤2.2kW)
No.
Name
Description
1
External keypad port
Connect the external keypad
2
Port cover
Protect the external keypad port
3
Cover
Protect the internal parts and components
4
Hole for the sliding cover
Fix the sliding cover
5
Trunking board
Protect the inner components and fix the cables of the
main circuit
6
Name plate
See section 2.5 "Name plate" for details.
7
Potentiometer knob
Refer to chapter 4 "Keypad operation procedure".
8
Control terminals
See chapter 3 "Installation guide" for details.
9
Main circuit terminals
See chapter 3 "Installation guide" for details.
10
Screw hole
Fix the fan cover and fan.
11
Cooling fan
See chapter 6 "Fault tracking" for details.
12
Fan cover
Protect the fan
13
Bar code
The same as the bar code on the name plate
Note: The bar code is on the middle shell which is under
the cover.
Note: In above figure, the screws at 4 and 10 are provided with packaging and specific
installation depends on the requirements of customers.
Below is the layout figure of the VFD (Three phase 400V, ≥4kW) (take the VFD of 4kW as the
example).

Goodrive20-EU series VFD Product overview
13
Figure 2-3 Product structure (Three phase 400V, ≥4kW)
No.
Name
Description
1
External keypad port
Connect the external keypad
2
Cover
Protect the internal parts and components
3
Keypad
Refer to chapter 4 "Keypad operation procedure".
4
Cooling fan
See chapter 6 "Fault tracking" for details
5
Name plate
See 2.5 "Name plate" for details.
6
Cover for the heat
emission hole
Optional, enhancement of the protective degree. It
is necessary to derate the VFD because the internal
temperature is increasing
7
Control terminals
See chapter 3 "Installation guide" for details.
8
Main circuit terminals
See chapter 3 "Installation guide" for details.
9
The cable entry of the
main circuit
Fix the cables
10
Simple name plate
Refer to section 2.6 "Type designation key".
11
Bar code
The same as the bar code on the name plate
Note: The bar code is on the middle shell which is
under the cover

Goodrive20-EU series VFD Installation guide
14
3 Installation guide
The chapter describes the mechanical installation and electric installation.
Only qualified electricians are allowed to carry out what described in this
chapter. Please operate as the instructions in chapter 1 "Safety
precautions".Ignoring these safety precautions may cause physical
injury or death or damage to the devices.
Ensure the power supply of the VFD is disconnected during the
operation. Wait for at least the time designated after the disconnection if
the power supply is applied.
The installation and design of the VFD should be complied with the
requirement of the local laws and regulations in the installation site. If
the installation infringes the requirement, our company will exempt from
any responsibility. Additionally, if users do not comply with the
suggestion, some damage beyond the assured maintenance range may
occur.
3.1 Mechanical installation
3.1.1 Installation environment
The installation environment is the safeguard for a full performance and long-term stable
functions of the VFD. Check the installation environment as follows:
Environment
Conditions
Installation
site
Indoor
Environment
temperature
-10°C to +50°C, and the temperature changing rate is less than 0.5°C/minute.
If the ambient temperature of the VFD is above 40°C, derate 1% for every
additional 1°C.
It is not recommended to use the VFD if the ambient temperature is above
50°C.
In order to improve the reliability of the device, do not use the VFD if the
ambient temperature changes frequently.
Please provide cooling fan or air conditioner to control the internal ambient
temperature below the required one if the VFD is used in a closed space such
as in the control cabinet.
When the temperature is too low, if the VFD needs to restart to run after a long
stop, it is necessary to provide an external heating device to increase the
internal temperature; otherwise, damage to the devices may occur.
Humidity
RH≤90%. No condensation is allowed.

Goodrive20-EU series VFD Installation guide
15
Environment
Conditions
Storage
temperature
-40°C to +70°C, and the temperature changing rate is less than 1°C/minute.
Running
environment
condition
The installation site of the VFD should fulfill the following requirements.
a) Away from the electromagnetic radiation source;
b) Away from contaminative air, such as corrosive gas, oil mist and
flammable gas;
c) Foreign objects, such as metal power, dust, oil, water cannot fall into the
VFD (do not install the VFD on the flammable materials such as wood);
d) Away from direct sunlight, oil mist, steam and vibration environment.
Altitude
Below 1000m;
If the altitude is above 1000m, derate 1% for every additional 100m.
Vibration
≤ 5.8m/s2 (0.6g)
Installation
direction
The VFD should be installed on an upright position to ensure sufficient cooling
effect.
Note:
Goodrive20-EU series VFDs should be installed in a clean and ventilated environment
according to enclosure classification.
Cooling air must be clean, free from corrosive materials and electrically conductive dust.
3.1.2 Installation direction
The VFD may be installed on the wall or in a cabinet.
The VFD needs be installed in the vertical position. Check the installation site according to the
requirements below. Refer to Appendix B "Dimension drawings" for details.
3.1.3 Installation mode
(1) Wall and rail mounting for the VFDs (single phase 230V/three phase 400V, ≤2.2KW and
three phase 230V, ≤0.75KW)
a) Wall mounting
b) Rail mounting
Figure 3-1 Installation

Goodrive20-EU series VFD Installation guide
16
Note: the minimum space of Aand B is 100mm if H is 36.6mm and W is 35.0mm.
(2) Wall and flange mounting for the VFDs (three phase 400V, ≥4KW and three phase 230V,
≥1.5KW)
Flange
Figure 3-2 Installation
(1) Locate the position of the installation hole.
(2) Fix the screw or nut on the located position.
(3) Put the VFD against the wall.
(4) Tighten up the screws.