INVT Goodrive 35 Series User manual

Goodrive 35 Series
Close Loop Vector Control Inverter
GD 35 -5 R5 G- 4
www.barghmaher.ir
www.barghmaher.ir

Goodrive35 inverters Preface
1
Preface
Thanks for choosing our products.
Goodrive35 series inverters are high performance open loop vector inverters for controlling
asynchronous AC induction motors and permanent magnet synchronous motors. Applying
the most advanced non-velocity sensor vector control technology which keeps pace with the
leading international technology and DSP control system, our products enhances its
reliability to meet the adaptability to the environment, customized and industrialized design
with more optimized functions, more flexible application and more stable performance.
The control performance of Goodrive35 series inverters is as outstanding as that of the
leading sophisticated inverters on worldwide market. Goodrive35 series inverters integrate
the drive of asynchronous motors and synchronous motors, torque control and speed control,
meeting the high performance requirement of the customer applications and stepping on the
unique incorporated inverters with superexcellent control functions in this circle.
Simultaneously, comparing with the other kinds, Goodrive35 series inverters can adapt to
worse grid, temperature, humidity and dust with a better performance of anti-tripping and
improved the reliability.
Goodrive35 series inverters apply modularized design to meet the specific demand of
customers, as well as the demand of the whole industry flexibly and follow the trend of
industrial application to the inverters on the premise of meeting general need of the market.
Powerful speed control, torque control, simple PLC, flexible input/output terminals, pulse
frequency given, traverse control can realize various complicate high-accuracy drives and
provide integrative solution for the manufacturers of industrial devices, which contributes a
lot to the cost reducing and improves reliability.
Goodrive35 series inverters can meet the demand of environmental protection which
focuses on low noise and weakening electromagnetic interference in the application sites for
the customers.
This manual provides installation and configuration, parameters setting, fault diagnoses and
daily maintenance and relative precautions to customers. Please read this manual carefully
before the installation to ensure a proper installation and operation and high performance of
Goodrive35 series inverters.
If the product is ultimately used for military affairs or manufacture of weapon, it will be listed
on the export control formulated by Foreign Trade Law of the People's Republic of China.
Rigorous review and necessary export formalities are needed when exported.
Our company reserves the right to update the information of our products.
www.barghmaher.ir

Goodrive35 inverters Content
2
Content
Preface....................................................................................................................... 1
Content ...................................................................................................................... 2
Safety Precautions 1............................................................. 5
1.1 What this chapter contains............................................................................................ 5
1.2 Safety definition............................................................................................................ 5
1.3 Warning symbols.......................................................................................................... 5
1.4 Safety guidelines.......................................................................................................... 6
Quick Start-up 2............................................................10
2.1 What this chapter contains.......................................................................................... 10
2.2 Unpacking inspection.................................................................................................. 10
2.3 Application confirmation.............................................................................................. 10
2.4 Environment............................................................................................................... 11
2.5 Installation confirmation.............................................................................................. 11
2.6 Basic commission....................................................................................................... 12
Product Overview 3............................................................13
3.1 What this chapter contains.......................................................................................... 13
3.2 Basic principles .......................................................................................................... 13
3.3 Product specification .................................................................................................. 14
3.4 Name plate................................................................................................................. 17
3.5 Type designation key.................................................................................................. 17
3.6 Rated specifications ................................................................................................... 18
3.7 I/O PG card selection.................................................................................................. 20
3.8 Structure diagram....................................................................................................... 21
Installation guidelines 4...........................................................23
4.1 What this chapter contains.......................................................................................... 23
4.2 Mechanical installation................................................................................................ 23
4.3 Standard wiring .......................................................................................................... 29
4.4 Standard wiring (control circuit)................................................................................... 35
4.5 Layout protection........................................................................................................ 45
Keypad operation procedure 5...........................................................47
5.1 What this chapter contains.......................................................................................... 47
5.2 Keypad....................................................................................................................... 47
5.3 Keypad displaying...................................................................................................... 50
5.4 Keypad operation ....................................................................................................... 51
www.barghmaher.ir

Goodrive35 inverters Content
3
Function parameters 6 ............................................................54
6.1 What this chapter contains.......................................................................................... 54
6.2 Goodrive35 general series function parameters.......................................................... 54
Basic operation instruction 7..........................................................172
7.1 What this chapter contains........................................................................................ 172
7.2 First powering on...................................................................................................... 172
7.3 Vector control........................................................................................................... 177
7.4 SVPWM control........................................................................................................ 182
7.5 Torque control.......................................................................................................... 188
7.6 Parmeters of the motor............................................................................................. 191
7.7 Start-up and stop control .......................................................................................... 196
7.8 Frequency setting..................................................................................................... 201
7.9 Analog input............................................................................................................. 205
7.10 Analog output......................................................................................................... 207
7.11 Digital input ............................................................................................................ 211
7.12 Digital input ............................................................................................................ 221
7.13 Simple PLC............................................................................................................ 226
7.14 Multi-step speed running......................................................................................... 229
7.15 PID control ............................................................................................................. 231
7.16 Commissioning for special functions....................................................................... 235
7.17 Fault solutions........................................................................................................ 243
Fault tracking 8 .........................................................247
8.1 What this chapter contains........................................................................................ 247
8.2 Alarm and fault indications........................................................................................ 247
8.3 How to reset............................................................................................................. 247
8.4 Fault history.............................................................................................................. 247
8.5 Fault instruction and solution .................................................................................... 247
8.6 Common fault analysis ............................................................................................. 253
Maintenance and hardware diagnostics 9..........................................................259
9.1 What this chapter contains........................................................................................ 259
9.2 Maintenance intervals............................................................................................... 259
9.3 Cooling fan............................................................................................................... 262
9.4 Capacitors................................................................................................................ 263
9.5 Power cable ............................................................................................................. 265
Communication protocol 10........................................................266
10.1 What this chapter contains...................................................................................... 266
www.barghmaher.ir

Goodrive35 inverters Content
4
10.2 Brief instruction to Modbus protocol........................................................................ 266
10.3 Application of the inverter ....................................................................................... 267
10.4 RTU command code and communication data illustration ....................................... 273
10.5 Common communication fault................................................................................. 287
Extension card AppendixA...........................................288
A.1 What this chapter contains....................................................................................... 288
A.2 PROFIBUS/CANOPEN extension card..................................................................... 288
A.3 CANopen optional cards .......................................................................................... 306
Technical data Appendix B ...........................................307
B.1 What this chapter contains....................................................................................... 307
B.2 Ratings .................................................................................................................... 307
B.3 Grid specifications.................................................................................................... 308
B.4 Motor connection data.............................................................................................. 308
B.5 Applicable standards................................................................................................ 309
B.6 EMC regulations ...................................................................................................... 310
Dimension drawings Appendix C...........................................312
C.1 What this chapter contains....................................................................................... 312
C.2 Keypad structure...................................................................................................... 312
C.3 Inverter structure...................................................................................................... 313
C.4 Dimensions for inverters of AC 3PH 380V(-15%)~440V(+10%)................................ 314
C.5 Dimensions for inverters of AC 3PH 520V(-15%)~690V(+10%)................................ 317
Peripheral options and parts Appendix D...........................................321
D.1 What this chapter contains....................................................................................... 321
D.2 Peripherial wiring ..................................................................................................... 321
D.3 Power supply........................................................................................................... 322
D.4 Cables..................................................................................................................... 323
D.5 Breaker and electromagnetic contactor .................................................................... 328
D.6 Reactors.................................................................................................................. 330
D.7 Filter........................................................................................................................ 333
D.8 Braking system........................................................................................................ 336
Further information Appendix E ...........................................342
www.barghmaher.ir

Goodrive35 inverters Safety precautions
5
Safety Precautions 1
1.1 What this chapter contains
Please read this manual carefully and follow all safety precautions before moving, installing,
operating and servicing the inverter. If ignored, physical injury or death may occur, or
damage may occur to the devices.
If any physical injury or death or damage to the devices occurs for ignoring to the safety
precautions in the manual, our company will not be responsible for any damages and we are
not legally bound in any manner.
1.2 Safety definition
Danger:
Serious physical injury or even death may occur if not follow
relevant requirements
Warning:
Physical injury or damage to the devices may occur if not follow
relevant requirements
Note:
Physical hurt may occur if not follow relevant requirements
Qualified
electricians:
People working on the device should take part in professional
electrical and safety training, receive the certification and be
familiar with all steps and requirements of installing,
commissioning, operating and maintaining the device to avoid any
emergency.
1.3 Warning symbols
Warnings caution you about conditions which can result in serious injury or death and/or
damage to the equipment, and advice on how to avoid the danger. Following warning
symbols are used in this manual:
Symbols
Name
Instruction
Abbreviation
Danger
Electrical
Danger
Serious physical injury or even
death may occur if not follow the
relative requirements
Warning
General
danger
Physical injury or damage to the
devices may occur if not follow the
relative requirements
www.barghmaher.ir

Goodrive35 inverters Safety precautions
6
Symbols
Name
Instruction
Abbreviation
Do not
Electrostatic
discharge
Damage to the PCBA board may
occur if not follow the relative
requirements
Hot sides
Hot sides
Sides of the device may become
hot. Do not touch.
Note
Note
Physical hurt may occur if not follow
the relative requirements
Note
1.4 Safety guidelines
Only qualified electricians are allowed to operate on the inverter.
Do not carry out any wiring and inspection or changing components when
the power supply is applied. Ensure all input power supply is disconnected
before wiring and checking and always wait for at least the time designated
on the inverter or until the DC bus voltage is less than 36V. Belowis the table
of the waiting time:
Inverter module
Minimum waiting time
380V
1.5kW-110kW
5 minutes
380V
132 kW -315 kW
15 minutes
660V
22kW-132kW
5 minutes
660V
160kW-350kW
15 minutes
660V
400kW-630kW
25 minutes
Do not refit the inverter unauthorizedly; otherwise fire, electric shock or other
injury may occur.
The base of the radiator may become hot during running. Do not touch to
avoid hurt.
The electrical parts and components inside the inverter are electrostatic.
Take measurements to avoid electrostatic discharge during relevant
operation.
1.4.1 Delivery and installation
Please install the inverter on fire-retardant material and keep the inverter
away from combustible materials.
Connect the braking optional parts (braking resistors, braking units or
www.barghmaher.ir

Goodrive35 inverters Safety precautions
7
feedback units) according to the wiring diagram.
Do not operate on the inverter if there is any damage or components loss to
the inverter.
Do not touch the inverter with wet items or body, otherwise electric shock
may occur.
Note:
Select appropriate moving and installing tools to ensure a safe and normal running of
the inverter and avoid physical injury or death. For physical safety, the erector should
take some mechanical protective measurements, such as wearing exposure shoes
and working uniforms.
Ensure to avoid physical shock or vibration during delivery and installation.
Do not carry the inverter by its cover. The cover may fall off.
Install away from children and other public places.
The inverter cannot meet the requirements of low voltage protection in IEC61800-5-1
if the sea level of installation site is above 2000m.
Please use the inverter on appropriate condition (See chapter Installation
Environment).
Don't allow screws, cables and other conductive items to fall inside the inverter.
The leakage current of the inverter may be above 3.5mAduring operation. High
leakage current, earth connection essential before connecting supply. Ground with
proper techniques and ensure the grounding resistor is less than 10Ω. The
conductivity of PE grounding conductor is the same as that of the phase conductor
(with the same cross sectional area).
R, S and Tare the input terminals of the power supply, while U, V and W are the motor
terminals. Please connect the input power cables and motor cables with proper
techniques; otherwise the damage to the inverter may occur.
1.4.2 Commission and running
Disconnect all power supplies applied to the inverter before the terminal
wiring and wait for at least the designated time after disconnecting the
power supply.
High voltage is present inside the inverter during running. Do not carry
out any operation except for the keypad setting.
The inverter may start up by itself when P01.21=1. Do not get close to
www.barghmaher.ir

Goodrive35 inverters Safety precautions
8
the inverter and motor.
The inverter can not be used as “Emergency-stop device”.
The inverter can not be used to break the motor suddenly. A mechanical
braking device should be provided.
Besides the above items, check to ensure the following ones before the
installation and maintenance during the running of the permanent
synchronization motor:
1. All input power supply is disconnected (including the main power
supply and the control power supply).
2. The permanent magnet synchronization motor has stopped
running and measured to ensure the output voltage of the inverter
is less than 36V.
3. The waiting time of the permanent magnet synchronization motor
after stopping is no less than the time designated and measure to
ensure the voltage between + and –is less than 36V.
4. Ensure the permanent magnet synchronization motor does not
rotate again because of the external load. It is recommended to
install effectively external braking devices or disconnect the electric
wiring between the motor and the inverter directly.
Note:
Do not switch on or off the input power supply of the inverter frequently.
For inverters that have been stored for a long time, check and fix the capacitance and
try to run it again before utilization (see Maintenance and Hardware Fault
Diagnose).
Cover the front board before running, otherwise electric shock may occur.
1.4.3 Maintenance and replacement of components
Only qualified electricians are allowed to perform the maintenance,
inspection, and components replacement of the inverter.
Disconnect all power supplies to the inverter before the terminal wiring.
Wait for at least the time designated on the inverter after disconnection.
Take measures to avoid screws, cables and other conductive matters to
fall into the inverter during maintenance and component replacement.
Note:
www.barghmaher.ir

Goodrive35 inverters Safety precautions
9
Please select proper torque to tighten screws.
Keep the inverter, parts and components away from combustible materials during
maintenance and component replacement.
Do not carry out any isolation and pressure test on the inverter and do not measure
the control circuit of the inverter by megameter.
Carry out a sound anti-electrostatic protection to the inverter and its internal
components during maintenance and component replacement.
1.4.4 What to do after scrapping
There are heavy metals in the inverter. Deal with it as industrial effluent.
www.barghmaher.ir

Goodrive35 inverters Quick start-up
10
Quick Start-up 2
2.1 What this chapter contains
This chapter mainly describes the basic guidelines during the installation and commission
procedures on the inverter, which you may follow to install and commission the inverter
quickly.
2.2 Unpacking inspection
Check as followings after receiving products:
1. Check that there are no damage and humidification to the package. If not, please contact
with local agents or company offices.
2. Check the information on the type designation label on the outside of the package to
verify that the drive is of the correct type. If not, please contact with local dealers or
company offices.
3. Check that there are no signs of water in the package and no signs of damage or breach
to the inverter. If not, please contact with local dealers or company offices.
4. Check the information on the type designation label on the outside of the package to
verify that the name plate is of the correct type. If not, please contact with local dealers or
company offices.
5. Check to ensure the accessories (including user’s manual, control keypad and extension
card) inside the device is complete. If not, please contact with local dealers or company
offices.
2.3 Application confirmation
Check the machine before beginning to use the inverter:
1. Check the load type to verify that there is no overload of the inverter during work and
check that whether the drive needs to modify the power degree.
2. Check that the actual current of the motor is less than the rated current of the inverter.
3. Check that the control accuracy of the load is the same of the inverter.
4. Check that the incoming supply voltage is correspondent to the rated voltage of the
inverter.
5. Check that the communication needs option card or not.
www.barghmaher.ir

Goodrive35 inverters Quick start-up
11
2.4 Environment
Check as followings before the actual installation and usage:
1. Check that the ambient temperature of the inverter is below 40℃. If exceeds, derate 1%
for every additional 1℃. Additionally, the inverter can not be used if the ambient
temperature is above 50℃.
Note: for the cabinet inverter, the ambient temperature means the air temperature inside
the cabinet.
2. Check that the ambient temperature of the inverter in actual usage is above -10℃. If not,
add heating facilities.
Note: for the cabinet inverter, the ambient temperature means the air temperature inside
the cabinet.
3. Check that the altitude of the actual usagesite is below 1000m. If exceeds, derate 1% for
every additional 100m.
4. Check that the humidity of the actual usage site is below 90% and condensation is not
allowed. If not, add additional protection inverters.
5. Check that the actual usage site is away from direct sunlight and foreign objects can not
enter the inverter. If not, add additional protective measures.
6. Check that there is no conductive dust or flammable gas in the actual usage site. If not,
add additional protection to inverters.
2.5 Installation confirmation
Check as followings after the installation:
1. Check that the load range of the input and output cables meet the need of actual load.
2. Check that the accessories of the inverter are correctly and properly installed. The
installation cables should meet the needs of every component (including reactors, input
filters, output reactors, output filters, DC reactors, braking units and braking resistors).
3. Check that the inverter is installed on non-flammable materials and the calorific
accessories (reactors and brake resistors) are away from flammable materials.
4. Check that all control cables and power cables are run separately and the routation
complies with EMC requirement.
5. Check that all grounding systems are properly grounded according to the requirements
of the inverter.
6. Check that the free space during installation is sufficient according to the instructions in
user’s manual.
www.barghmaher.ir

Goodrive35 inverters Quick start-up
12
7. Check that the installation conforms to the instructions in user’s manual. The drive must
be installed in an upright position.
8. Check that the external connection terminals are tightly fastened and the torque is
appropriate.
9. Check that there are no screws, cables and other conductive items left in the inverter. If
not, get them out.
2.6 Basic commission
Complete the basic commissioning as followings before actual utilization:
1. Select the motor type, set correct motor parameters and select control mode of the
inverter according to the actual motor parameters.
2. Autotune. If possible, de-coupled from the motor load to start dynamic autotune. Or if not,
static autotune is available.
3. Adjust the ACC/DEC time according to the actual running of the load.
4. Commission the device via jogging and check that the rotation direction is as required. If
not, change the rotation direction by changing the wiring of motor.
5. Set all control parameters and then operate.
www.barghmaher.ir

Goodrive35 inverters Product overview
13
Product Overview 3
3.1 What this chapter contains
The chapter briefly describes the operation principle, product characteristics, layout, name
plate and type designation information.
3.2 Basic principles
Goodrive35 series inverters are wall, floor and flange mountable devices for controlling
asynchronous AC induction motors and permanent magnet synchronous motors.
The diagram below shows the simplified main circuit diagram of the inverter. The rectifier
converts three-phase AC voltage to DC voltage. The capacitor bank of the intermediate
circuit stabilizes the DC voltage. The converter transforms the DC voltage back to AC
voltage for the AC motor. The brake pipe connects the external braking resistor to the
intermediate DC circuit to consume the feedback energy when the voltage in the circuit
exceeds its maximum limit.
Fig 3-1 The simplified main circuit diagram (inverters of 380V≥37kW)
Fig 3-2 The simplified main circuit diagram (inverters of 380V≤30kW)
www.barghmaher.ir

Goodrive35 inverters Product overview
14
Fig 3-3 The simplified main circuit diagram (inverters of 660V)
Note:
1. The inverters of 380V(≥37kW) supports external DC reactors and external braking units,
but it is necessary to remove the copper tag between P1 and(+) before connecting. DC
reactors and external braking units are optional.
2. The inverters of 380V (≤30kW) supports external braking resistors which are optional.
3. The inverters of 660V supports external DC reactors and external braking units, but it is
necessary to remove the copper tag between P1 and (+) before connecting. DC reactors
and external braking units are optional.
3.3 Product specification
Function
Specification
Power
input
Input voltage (V)
AC 3PH 380V(-15%)~440V(+10%)
Rated voltage:380V
AC 3PH 520V(-15%)~690V(+10%)
Rated voltage:660V
Input current (A)
Refer to the rated value
Input frequency (Hz)
50Hz or 60Hz
Allowed range: 47~63Hz
Power
output
Output voltage (V)
0~input voltage
Output current (A)
Refer to the rated value
Output power (kW)
Refer to the rated value
Output frequency
(Hz)
0~400Hz
Technical
control
Control mode
SVPWM, SVC and VC
Motor type
Asynchronous motor and permanent magnet
www.barghmaher.ir

Goodrive35 inverters Product overview
15
Function
Specification
feature
synchronous motor
Adjustable-speed
ratio
Asynchronous motor 1:200 (SVC) synchronous
motor 1:20 (SVC) 1:1000 (VC)
Speed control
accuracy
±0.2% (SVC) ±0.02% (VC)
Speed fluctuation
±0.3%(SVC)
Torque response
<20ms(SVC)<10ms(VC)
Torque control
accuracy
10%(SVC) 5%(VC)
Starting torque
Asynchronous motor: 0.25Hz/150%(SVC)
Synchronous motor: 2.5 Hz/150%(SVC)
0Hz/150%(VC)
Overload capability
150% of rated current: 1 minute
180% of rated current: 10 seconds
200% of rated current: 1 second
Running
control
feature
Frequency setting
method
Digital setting, analog setting, pulse frequency
setting, multi-step speed running setting, simple
PLC setting, PID setting, MODBUS communication
setting, PROFIBUS communication setting
Switch between the combination and single setting
channel
Auto-adjustment of
the voltage
Keep constant voltage automatically when the grid
voltage transients
Fault protection
Provide more than 30 fault protection functions:
overcurrent, overvoltage, undervoltage, overheating,
phase loss and overload, etc.
Restart after rotating
speed tracking
Smooth starting of the rotating motor
Note: Only for the inverter≥4kW
Peripheral
interface
Terminal analog input
resolution
≤20mV
Terminal switch input
resolution
≤2ms
www.barghmaher.ir

Goodrive35 inverters Product overview
16
Function
Specification
Analog input
2 (AI1, AI2) 0~10V/0~20mAand 1 (AI3) -10~10V
Analog output
2 (AO1, AO2) 0~10V /0~20mA
Digital input
8 common inputs, the Max. frequency: 1kHz,
internal impedance: 3.3kΩ;
1 high speed input, the Max. frequency: 50kHz
Digital output
1 high speed pulse output, the Max. frequency:
50kHz;
1 Y terminal open collector output
Relay output
2 programmable relay outputs
RO1A NO, RO1B NC, RO1C common terminal
RO2A NO, RO2B NC, RO2C common terminal
Contactor capability: 3A/AC250V,1A/DC30V
Spindle stopping
For spindle positioning and control sequence
Internal 7 scale marks and 4 zero marks
Position reference
External zero-position detection switch positioning
Encoder Z phase positioning
Servo control
Pulse train reference: position control
Frequency division
output
Encoder frequency division output
(H1 and H2 inverters)
Speed/position mode
Terminal shifting
Encoder
C1 support 100kHz, D1 support 500kHz, H1 support
300kHz and H2 support 400kHz
Positioning
Z pulse and photoelectric switch positioning
Others
Mountable method
Wall, flange and floor mountable
Temperature of the
running environment
-10~50℃, if temperature is above 40℃, derate 1%
for every additional 1℃.
Average non-fault
time
2 years (25℃ambient temperature)
Protective degree
IP20
Cooling
Air-cooling
Braking unit
Built-in for inverters of 380V(≤30kW)
External for others
www.barghmaher.ir

Goodrive35 inverters Product overview
17
Function
Specification
EMC filter
Built-in C3 filter for 380V inverters: meet the degree
requirement of IEC61800-3 C3
No built-in filters for 660V inverters
External filter:optional, meet the degree requirement
of IEC61800-3 C2
3.4 Name plate
Fig 3-4 Name plate
Note: After the CE certification, the icon can be marked.
3.5 Type designation key
The type designation contains information on the inverter. The user can find the type
designation on the type designation label attached to the inverter or the simple name plate.
3.5.1 Model
GD35 –5R5G –4 –H1
①②③④
Key
Sign
Instruction
Content
Abbreviation
①
Abbreviation
Goodrive35: Goodrive35 close-loop vector
control inverters
Rated power
②
Power + Load
5R5-5.5kW
G—constant torque load
Voltage
degree
③
Voltage degree
4:AC 3PH 380V(-15%)~440V(+10%)
Rated voltage:380V
6:AC 3PH 520V(-15%)~690V(+10%)
www.barghmaher.ir

Goodrive35 inverters Product overview
18
Key
Sign
Instruction
Content
Rated voltage:660V
Lot number
④
Lot number
C1: support 24V incremental encoder
D1: support rotary transformer
Optional PG cards with functions of pulse and
direction pulse input reference
H1: support 5V/12V incremental encoder,
Pulse + direction pulse input reference
H2: support 5V incremental encoder for high
speed differential signal processing,
Pulse + direction pulse input reference (special
for machine tools)
3.6 Rated specifications
3.6.1 The inverters of AC 3PH 380V(-15%)~440V(+10%)
Model
Rated
output
power(kW)
Rated
input
current(A)
Rated
output
current(A)
Model
GD35-1R5G-4-C1/D1/H1
1.5
5.0
3.7
1~15(8)
GD35-2R2G-4-C1/D1/H1
2.2
5.8
5
1~15(8)
GD35-004G-4-C1/D1/H1/H2
4
13.5
9.5
1~15(8)
GD35-5R5G-4-C1/D1/H1/H2
5.5
19.5
14
1~15(8)
GD35-7R5G-4-C1/D1/H1/H2
7.5
25
18.5
1~15(8)
GD35-011G-4-C1/D1/H1/H2
11
32
25
1~1s5(8)
GD35-015G-4-C1/D1/H1/H2
15
40
32
1~15(4)
GD35-018G-4-C1/D1/H1/H2
18.5
47
38
1~15(4)
GD35-022G-4-C1/D1/H1/H2
22
56
45
1~15(4)
GD35-030G-4-C1/D1/H1/H2
30
70
60
1~15(4)
GD35-037G-4-C1/D1/H1
37
80
75
1~15(4)
GD35-045G-4-C1/D1/H1
45
94
92
1~15(4)
GD35-055G-4-C1/D1/H1
55
128
115
1~15(4)
GD35-075G-4-C1/D1/H1
75
160
150
1~15(2)
GD35-090G-4-C1/D1/H1
90
190
180
1~15(2)
www.barghmaher.ir

Goodrive35 inverters Product overview
19
Model
Rated
output
power(kW)
Rated
input
current(A)
Rated
output
current(A)
Model
GD35-110G-4-C1/D1/H1
110
225
215
1~15(2)
GD35-132G-4-C1/D1/H1
132
265
260
1~15(2)
GD35-160G-4-C1/D1/H1
160
310
305
1~15(2)
GD35-185G-4-C1/D1/H1
185
345
340
1~15(2)
GD35-200G-4-C1/D1/H1
200
385
380
1~15(2)
GD35-220G-4-C1/D1/H1
220
430
425
1~15(2)
GD35-250G-4-C1/D1/H1
250
460
480
1~15(2)
GD35-280G-4-C1/D1/H1
280
500
530
1~15(2)
GD35-315G-4-C1/D1/H1
315
580
600
1~15(2)
Note:
1. The input current of inverters 1.5~315kW is detected when the input voltage is 380V and
there is no DC reactors and input/output reactors.
2. The rated output current is defined when the output voltage is 380V.
3. The output current can not exceed the rated output current and the output power can not
exceed the rated output power in the voltage range.
3.6.2 The inverters of AC 3PH 520V(-15%)~690V(+10%)
Model
Rated
output
power(kW)
Rated
input
current(A)
Rated
output
current(A)
Carrier
frequency
(kHz)
GD35-022G-6-C1/D1/H1
22
35
27
1~15(4)
GD35-030G-6-C1/D1/H1
30
40
34
1~15(4)
GD35-037G-6-C1/D1/H1
37
47
42
1~15(4)
GD35-045G-6-C1/D1/H1
45
52
54
1~15(4)
GD35-055G-6-C1/D1/H1
55
65
62
1~15(4)
GD35-075G-6-C1/D1/H1
75
85
86
1~15(2)
GD35-090G-6-C1/D1/H1
90
95
95
1~15(2)
GD35-110G-6-C1/D1/H1
110
118
131
1~15(2)
GD35-132G-6-C1/D1/H1
132
145
147
1~15(2)
GD35-160G-6-C1/D1/H1
160
165
163
1~15(2)
GD35-185G-6-C1/D1/H1
185
190
198
1~15(2)
www.barghmaher.ir