Ironmaster Cable Tower Attachment Quick setup guide

Ironmaster Cable Tower Attachment
Assembly and Use Instructions
The Cable Tower Attachment is designed to connect to the Ironmaster Super Bench to
allow upper and lower pulley cable work. It has a unique weight carriage that allows
the use of the Ironmaster Quick-Lock Dumbbells to be the weight source or it will also
work with Standard or Olympic style plates. The system capacity is rated at 250lbs.
This device is not safe to use stand alone. It must always be connected to the Super
Bench when in use for safety.

Congratulations on your purchase of this fine Ironmaster product. The following instructions will help
you assemble the unit and provide some details on use as well. The only tools required are two
adjustable wrenches. Unpack all the parts and make sure you have received all the parts as shown on
the exploded view drawing and parts list. If you are missing anything or need anything, please call
Ironmaster right away and we will assist you. 800-533-3339.
Step 1: Assemble FRONT BRACKET #11
and REAR LOW PULLEY BRACKET #15 to
BASE FRAME #9 using bolts #1, washers #3
and Nuts #2. Be sure to insert bolts from
underside of BASE FRAME with nuts and
washers on top. Refer to exploded view on
page 7 for orientation.
Step 2: Assemble FRONT TUBE UPRIGHT #21
and SLIDE RAIL #17 using bolts #4 and washers
Step 3: Assemble BENCH CONNECTOR #10
(chrome plated) to FRONT TUBE UPRIGHT
#21 using bolt #4 and washer #3 on top and
Bolt #1 and washer #3 on bottom. Be sure to
locate hole for bench pull pin on left hand side
as shown. Note: The connector can be ad-
justed up or down to match up to the bench if
necessary.
1 2
Step 4: Install ROUND TUBE #18 using bolt #5 and
washer #3. Push FOAM SPACER PADS #14 on first
then the FOAM ROLLER PADS #13. Secure with
bolt #7, dome cap #12 and washer #8 as shown in
exploded view. Note: There are 3 height positions
available so you can select the most comfortable
height for the leg hold down.
3
4
2

Step 5: Install SPRING #16 and WEIGHT
CARRIAGE #23 over SLIDE RAIL #17 as
shown.
5
Step 6: Install TOP PULLEY BRACKET #25 as shown
using bolts #1, washers #3 and nuts #2. Install pulleys
#15a with black bolts and hex nuts with one washer
under nut on this part as well as the LOW PULLEY
BRACKET #15.
6
7a
7a
3
Step 7b: If you plan to use the Ironmaster
Quick-Lock Dumbbells as the weight source
on the carriage, install the CARRIAGE
DUMBBELL ADAPTER #24 using bolt #6 and
washers #3 with the Allen wrench as shown in
the exploded view.
7b
Step 7: If you plan to use Olympic style
weight plates on the weight carriage, you can
install the 2 included OLYMPIC SLEEVE
ADAPTERS #28 as shown. Secure with the
set screws. Push on the rubber rings #29 as
bumpers.

Cable system set up for
upper pulley work.
Carriage set up to accept
the dumbbells.
Note: The Super Bench is
not shown in this illustration
but should always be
attached when in use.
4

Select either the shorter FRONT CABLE #26 for upper pulley work or the longer REAR CABLE #27 for
lower pulley work. The CHAIN #20 may be connected to the cable end to lengthen the reach from the
upper or lower pulley. Take care when routing the pulley cables to be sure they fit completely in the
grooves. The SNAP HOOKS #22 are used to connect the cables to the CARRIAGE #23 and to the ex-
ercise handle you select. The system includes the LAT PULL DOWN HANDLE #19 that can be used for
lat pulls, cable press downs, low rows, cable curls, upright rows, etc. You may use a variety of cable
handles with this system—sold separately.
Cable system set up with
Rear Cable for low pulley
work. Olympic weight
sleeves shown in place.
Note: The Super Bench is
not shown in this illustration
but should always be
attached when in use.
5

6
Warranty Information:
Your Ironmaster attachment has a limited 10 year warranty to the original purchaser. Cables and pad-
ding are covered for two years. Warranty covers repair or replacement for mechanical integrity when
used according to the instructions for normal exercise use. Warranty covers in home use only. Finish
and wear items such as rubber and painted surfaces are not covered. If you need warranty service,
contact Ironmaster for return instructions and additional terms and conditions.
Ironmaster LLC, 21828 87th Ave SE, #E, Woodinville, WA 98072 800-533-3339, 425-408-9040
PARTS LIST FOR IRONMASTER CABLE TOWER ATTACHMENT
No. Description Qty Detail
1 Bolt - M10x70 7 Chrome
2 Nut - Nylon insert nut 10mm 6 Chrome
3 Washer - 10mm 18 Chrome
4 Bolt - M10x20 8 Chrome
5 Bolt - M10x25 1 Chrome
6 Bolt- Allen Head M10x35 2 Black
7 Bolt- Allen Head M8x25 2 Black
8 Washer - M8 2 Chrome
9 Base Frame 1 Powder coated grey
10 Bench Connecter 1 Chrome
11 Front Bracket 1 Powder coated grey
12 Plastic Dome Cap 2 Black cap for foam roller pads
13 Foam Roller Pad 2 Black Neoprene
14 Foam Spacer Pad 2 Black rubber - small
15 Rear Low Pulley Bracket 1 Powder Coated Grey
16 Spring 1 Chrome
17 Slide Rail 1 Powder Coated Grey
18 Round Tube - 1" dia. 1 Powder Coated Grey - foam roller pad holder
19 Lat Pull Down Handle 1 Chrome
20 Chain 1 Chrome
21 Front Tube Upright 1 Powder Coated Grey
22 Snap Hook 3 Chrome
23 Weight Carriage 1 Powder Coated Grey with slide bushings
24 Carriage Dumbbell Adapter 1 Powder Coated Grey
25 Top Pulley Bracket 1 Powder Coated Grey
26 Front Cable 1 76" long with rubber stop
27 Rear Cable 1 130.5" long with rubber stop
28 Olympic Sleeve Adapter 2 Chrome, 2" x 9"
15a Cable Pulley 3 Black plastic
29 Rubber Bumpers 2 Rubber ring for when the Olympic sleeves are used
Optional attachments are available such as the Low Row Footplate, Dockable Curl Support and various
cable attachment handles. Please visit www.ironmaster.com for more details.

Exploded View—Ironmaster Cable Tower
15a
15a
7