Iseki TXG237 User manual

TXG237
MODEL:
ISEKI TRACTOR

TO OUR CUSTOMER
1
Thank you very much for purchasing an ISEKI tractor.
This operator’s manual provides the information necessary for operating and maintaining
your tractor safely and properly. The contents are mainly composed of the following 2 items:
Safety instructions : Essential items which you should observe while
operating the tractor
Technical instructions : Items which are necessary to operate, adjust and
service the tractor properly
Before starting to operate the machine for the first time, you should read this operation
manual thoroughly and carefully until you are sufficiently familiar with the operation of the
machine to do jobs safely and properly. The manual should be kept in a handy place so
you can refer to it when required. You are advised to refer to it from time to time to refresh
your understanding of the machine.
Your dealer has performed the pre-delivery service on your new machine.
He will discuss with you the operating and maintenance instructions given in this manual,
and instruct you in the proper and varied applications of this machine. Call on him at any
time when you have a question, or need equipment related to the use of your machine.
Paragraphs in the manual and labels on the machine which are accompa-
nied by a caution mark contain particularly important information about safe
operation to avoid accidents. You should always keep precautions in mind
and follow them during operation.
Be sure to wear
personnel protective equipment
during operation
In some of the illustrations used in this operation manual, panels or
guards may have been removed for clarity. Never operate the tractor
with these panels and guards removed. If the removal of a shield is
necessary to make a repair, it must be replaced before operation.
All information, illustrations, and specifications contained in this manual are based on
the latest information available at the time of publication. The right is reserved to make
changes at any time without notice.
TO OUR CUSTOMER

TABLE OF CONTENTS
3
TO OUR CUSTOMER ................................................1
TABLE OF CONTENTS.............................................3
1. SAFETY .................................................................5
MACHINE PURPOSE ............................................5
PERSONAL SAFETY INSTRUCTIONS .................5
MAKING YOUR TRACTOR A SAFE VEHICLE......6
■HOW TO MAINTAIN SAFETY............................6
FOR SAFE OPERATION .......................................7
■HOW TO BE A SAFE OPERATOR.....................7
■WHEN ANOTHER PERSON OPERATES
YOUR MACHINE ...............................................7
■BEFORE OPERATION.......................................8
■STARTING ENGINE AND MOVING
TRACTOR..........................................................8
■WHEN TRAVELLING .........................................9
■LOADING ONTO OR UNLOADING FROM
A TRUCK..........................................................10
■DURING OPERATION ..................................... 11
■INSPECTION AND MAINTENANCE................12
■STORAGE........................................................13
MAINTENANCE OF THE ELECTRIC SYSTEM ..14
■
TO MAINTAIN ELECTRIC WIRING.................14
■
TO HANDLE THE BATTERY...........................14
■
TO HANDLE BOOSTER CABLES...................15
■
DISMANTLING AND DISPOSAL.....................15
■
SAFETY DECALS............................................15
■
SAFETY DECALS AND THEIR LOCATIONS..16
2. TRACTOR IDENTIFICATION ..............................20
HOMOLOGATION ATTESTATION NUMBERS
MODEL / SERIAL NUMBERS ..............................20
MODEL TYPE DESIGNATION.............................21
MAJOR COMPONENTS......................................22
3. INSTRUMENTS & CONTROLS...........................24
INSTRUMENT PANEL .........................................25
MAIN SWITCH .....................................................25
Indicator Light Strip ..........................................26
Hour Meter .......................................................26
Horn / Light Turn Switch ..................................27
Fuel Gauge.......................................................27
Coolant Temperature Gauge............................28
Tachometer.......................................................28
BRAKES...............................................................28
Brake Pedal......................................................28
Parking Brake...................................................29
ENGINE SPEED CONTROLS .............................29
Throttle Lever ...................................................29
TRANSMISSION SHIFT LEVER AND
CONTROLS .........................................................29
DIFFERENTIAL LOCK PEDAL ............................30
FOUR-WHEEL DRIVE SHIFT LEVER .................30
PTO CLUTCH LEVER..........................................30
REAR & MID PTO SELECTOR LEVERS.............31
THREE-POINT HITCH .........................................31
Control Lever....................................................31
Lowering Rate Control Knob ............................32
Cutting Height Control Knob ............................32
COMFORT ADJUSTMENT ..................................32
Seat Adjustment (E6 Type)...............................32
Seat Switch ......................................................32
REAR VIEW MIRROR (E4 Type) .........................33
4. OPERATION ........................................................34
BREAK-IN PERIOD..............................................34
STARTING............................................................34
Pre-Start Inspection..........................................34
Normal Starting ................................................35
Restarting Warm Engine ..................................36
Cold Weather Starting......................................36
Warm-Up Period...............................................36
Operator Observations.....................................37
Starting Circuit Operation.................................37
GROUND SPEED SELECTION...........................38
Hydrostatic Transmission .................................38
STOPPING TRACTOR.........................................39
DIFFERENTIAL LOCK .........................................40
FOUR-WHEEL DRIVE .........................................40
POWER TAKE OFF (PTO)...................................41
Rear PTO Shaft................................................42
Mid PTO Shaft..................................................42
PTO Operating Controls...................................43
3-POINT HITCH ...................................................44
Hitch Controls...................................................44
Rear Linkage....................................................44
Attaching Implements.......................................45
Using Position Control......................................46
Detaching Implements .....................................47
Cutting Height Control Knob ............................47
How to adjust Height Control ...........................48
ROLL OVER PROTECTIVE STRUCTURE
(ROPS) ................................................................49
EXTERNAL AUXILIARY HYDRAULICS
(V Type)................................................................50
REAR HITCH .......................................................51
FRONT LOADER FIXATION POINT....................51
FALLING OBJECTIVES PROTECTIVE
STRUCTURE (FOPS) & OPERATORS
PROTECTION STRUCTURE (OPS)
FIXATION POINT .................................................51
5. MAINTENANCE & ADJUSTMENT......................52
SPECIFICATIONS & CAPACITIES ......................52
Engine Oil.........................................................52
PERIODIC MAINTENANCE SCHEDULE ............53
LUBRICATION/FILL POINTS...............................54
SERVICE ACCESS ..............................................55
LUBRICATION DETAILS......................................59
Grease Fittings.................................................59
Engine Oil Filter................................................59
Transmission Oil & Filters ................................60
Front Axle Oil....................................................61
TABLE OF CONTENTS

TXG237
4
Check Oil Level ................................................61
Change Oil .......................................................61
COOLING SYSTEM.............................................62
ENGINE AIR CLEANER.......................................64
FUEL SYSTEM.....................................................65
Fuel Filter .........................................................65
Air-Bleeding Fuel System.................................66
Fuel Tank Filler Cap .........................................66
Throttle Lever ...................................................66
ELECTRICAL SYSTEM........................................67
Battery..............................................................67
Starting Switches..............................................68
Wiring/Fuse Arrangement.................................69
FUSE / Head Light ...............................................69
Trailer Socket (E4 Type)...................................73
Lamps...............................................................73
BRAKE ADJUSTMENT ........................................77
Parking Brake Lever Adjustment......................77
HYDROSTATIC ADJUSTMENTS.........................78
WHEELS & TYRES..............................................78
Tyre Inflation Pressures....................................78
Wheel Bolt Torque............................................78
Steering Free-Play ...........................................80
TORQUE CHART.................................................80
STORAGE............................................................81
TOWING (Type G)................................................82
JACKING..............................................................82
6. TROUBLESHOOTING.........................................83
ENGINE................................................................83
BRAKES...............................................................85
HYDRAULIC SYSTEM.........................................85
STEERING SYSTEM ...........................................86
ELECTRICAL SYSTEM........................................86
7. SPECIFICATIONS................................................87
■DIMENSIONAL LIMITS OF IMPLEMENTS......89
DIMENSIONS.......................................................90
LOAD CAPACITY.................................................90
NOISE DECLARATION........................................91
VIBRATION DECLARATION ...............................92
8. ASSEMBLY & PRE-DELIVERY INSPECTION....93
ASSEMBLY ..........................................................93
PRE-DELIVERY ...................................................94
9. ACCESSORIES ...................................................95
This manual explains about several types of the tractor listed below. Please confirm the type of yours by referring
to the name plate.
TABLE 1
Model TXG 237
Type FH FH
E4 RE4 GVRE4 E6
Area Europe Oceania
Mid PTO ○○○○
Single Air Cleaner ○○○○
Hydrostatic Power Steeri ng ○○○○
HST ○○○○
lndependent PTO ○○○○
2-speed Range Gear ○○○○
ISO Caution Label ○○○○
4WD ○○○○
E3 ROPS (SF-2400A) ○
E4 ROPS (SF-405) T ○○
Electrical System (USA type) ○
Electrical System (EC type) ○○○
Hand Parking Brake (seat side) ○○○○
Head Light (EC type) ○○○○
Back Mirror (EC type LH ) ○○○
Battery (55B24RIS) ○○○○
Seat & Seat Belt ○
Front Hitch T T ○
Cup Holder ○○○○
Cylinder case & Rear 3-Point Linkage ○○○○
MowerLinkage (Mechanica1) ○○○○
MowerLinkage (Hydrostatic) T T T T
Auxillary Hydraulic Valve (double) T T ○T
MufflerTail Direction (front side) ○○○○
Rear Hitch (EEC type) T T ○
Homologation plate ○
○; Standard T ; Option
All information, illustrations, and specifications contained in this manual are based on the latest information avail-
able at the time of publication. The right is reserved to make changes at any time without notice.

SAFETY
5
MACHINE PURPOSE
This machine is designed solely for use in customary
agricultural or similar operations.
Use in any other way is considered as contrary to the
intended use. Compliance with and strict adherence
to the conditions of operation, service, and repair as
specified by the manufacturer, also constitute essential
elements of the intended use. This machine should be
operated, serviced, and repaired only by persons who
are familiar with its particular characteristics and who
are acquainted with the relevant safety procedures.
Accident prevention regulations, all other generally
recognized regulations on safety and occupational
medicine, and all road traffic regulations must be ob-
served at all times. Any arbitrary modifications carried
out to this machine may relieve the manufacturer of
liability for any resulting damage or injury.
PERSONAL SAFETY INSTRUCTIONS
Whenever you see the words and symbols below,
used in this Operator's Instruction Book and on de-
cals, you MUST take note of their instructions as they
relate to personal safety.
DANGER: This symbol together with the
word DANGER indicates an imminently
hazardous situation that, if not avoided,
will result in DEATH OR VERY SERIOUS
INJURY.
WARNING: This symbol together with the
word WARNING indicates a potentially haz-
ardous situation that, if not avoided, could
result in DEATH OR VERY SERIOUS INJURY.
CAUTION: This symbol together with
the word CAUTION is used to indicate a
potentially hazardous situation that, if not
avoided, may result in MINOR INJURY.
IMPORTANT: The word IMPORTANT is used to iden-
tify special instruction or procedures
which, if not strictly observed, could re-
sult in damage to, or destruction of the
machine, process or its surrounding.
NOTE: The word NOTE is used to indicate points
of particular interest for more efficient and
convenient repair or operation.
Understand thoroughly the following precautions,
always keep them in mind before, during, and after
operation, and never take chances.
SAFETY

TXG237
6
MAKING YOUR TRACTOR A SAFE VEHICLE
■HOW TO MAINTAIN SAFETY
(1) Never attempt to do the following:
・Modification of the structure of the tractor
・Installation of other type of engine
・Installation of tyres of other than the original tyre
size. Any malfunctions or failures of the tractor
due to unauthorized modification are not covered
by the warranty.
(2) This machine cannot be driven on a public road
without authorization by a local government
agency, etc.
When transporting an unauthorized machine on a
public road, load it on a truck.
When travelling with an implement wider than the
tractor, put red caution markers such as flags (red
lamps at night) in the most visible locations on
both sides of the implements, and place a “SLOW
MOVING VEHICLE” sign in a place where it is
easily seen by other drivers. Operate the machine
carefully keeping in mind that the implement is
wide and may roll easily. If the implement can
be folded, fold it beforehand. If there are road or
railway crossings where the visibility is poor, you
should install on the machine a mirror to give a
view ahead of you so that you need not move
your machine too far into the intersection.
(3) When you travel on a road, you must turn work
lights off if the law requires it.
FIG. 1-1

SAFETY
7
FOR SAFE OPERATION
■HOW TO BE A SAFE OPERATOR
(1) Familiarize yourself fully with machine controls
by studying the operation manual before using
your machine.
This operation manual should be regarded as
part of the machine. Suppliers of both new and
second-hand machines are advised to retain
documentary evidence that this manual was pro-
vided with the machine.
(2) Never allow persons listed below to operate the
machine. If any work carried out by unauthorized
persons as below would affect the warranty on
the machinery.
・Persons with mental disease
・Persons who cannot operate the machine prop-
erly because of fatigue, illness, or drowsiness
from medication, etc.
・Pregnant women
・Young persons or children too young to legally
operate the machine
Always be careful of your health by taking suit-
able rest breaks.
(3) Wear appropriate clothing and other protective
devices during operation.
・Protection of your head
Wear protective headgear such as a helmet,
especially when travelling on roads or handling
material above your head.
・Protection to avoid being caught in the machine.
Wear tight fitting clothing and headgear, because
loose clothing or hair can get caught in the mov-
ing parts of the machine.
・Protection from poisonous dust or gases
Be sure to wear a protective device to protect the
respiratory system, eyes, and skin when handling
poisonous chemicals on work with such a crop
sprayer, mounted or trailed.
・Protection of the ears
Wear ear plugs or take suitable countermeasures
to protect your ears when you must operate the
machine under extremely noisy conditions.
・Maintenance of protective devices
Periodically inspect protective devices to assure
that they are functioning properly. Use them at
all times.
■
WHEN ANOTHER PERSON OPERATES YOUR
MACHINE
When another person operates your machine, you
must explain how to operate and instruct him or her
to read this manual fully to avoid unexpected accident.
FIG. 1-2
FIG. 1-3
FIG. 1-4
FIG. 1-5

TXG237
8
■BEFORE OPERATION
(1) Set up an operation plan with sufficient time al-
lowance. A tight plan may result in unexpected
accidents when work has to be rushed.
(2) Inspect and service the machine periodically in
accordance with the instructions given in the
operation manual to maintain the machine in best
condition.
Pay special attention to the controls, especially to
the brakes and HST pedal, and safety measures
for the machine when servicing it. If the machine
functions properly and performs normally, the
chance of an accident will be reduced greatly.
If safety devices are damaged or do not work,
please consult your Iseki dealer.
(3) Before removing a safety device, such as a safety
cover, be sure that the machine has stopped
completely. Never forget to replace the removed
part after servicing.
(4) Never fill fuel while the engine is running or is
still hot. Keep away from open fires an never
smoke around a fuel tank or while fuelling into the
machine. Never use open flames for illumination
when fuelling the machine at night.
■STARTING ENGINE AND MOVING TRACTOR
(1) Before starting the engine indoors, make sure
that there is proper ventilation because exhaust
fumes contain poisonous carbon monoxide, which
cause lethal poisoning.
(2) Before starting the machine, confirm that the
transmission gear has been shifted to the ap-
propriate speed, that there is no one near the ma-
chine and that the implement is securely installed
on the machine.
Always operate the machine from the operator’s
seat. Never leave the seat except in an emer-
gency when operating the machine.
(3) Before starting to move, pay attention to safety
conditions around the machine to avoid injury to
bystanders or damage to property. Never move
abruptly.
FIG. 1-6
FIG. 1-7
FIG. 1-8
FIG. 1-9

SAFETY
9
■WHEN TRAVELLING
(1) When you travel on roads, ensure the differential
lock is off, or the tractor may turn over.
(2) Do not make sharp turns when operating at
high speed or for transportation as the tractor
may turn over.
(3) When operating on poor footing such as a rough
road, a slope, a road along a ditch or river, or
undeveloped land, drive the tractor at low speeds
and operate it carefully.
(4) Do not make sharp turns on a slope. It may cause
turnover of the tractor.
When climbing up a hill, shift the speed change
lever to the most suitable speed. Start moving the
tractor as slowly as possible.
While climbing up a hill, never shift speeds along
the way.
When starting to move the tractor on an up-hill
slope, be sure that the front wheels do not lift up.
When going down a hill, drive the tractor at a
slower speed than used to climb up the hill.
While going down a hill, never disengage the
clutch or shift into neutral, and never try to control
the speed only with the brakes; use the engine
brake effectively.
(5) When travelling on a road where one or both
shoulders are slanted and which run along a
ditch, look out for softened shoulders especially
when the ditch is full of water and be careful not
to let the machine slip sideways.
(6) Never allow other persons to get on the machine
or the implement except when the machine or the
implement is provided with a seat or a platform
for persons to sit or stand on, and only within the
capacity specified.
Never allow persons to get on the implement
while travelling on roads.
(7) When parking the tractor, you have to park it on
hard, level ground and provide sufficient safety
measures by grounding the implement, removing
the key, applying the parking brakes, and chock-
ing the wheels securely.
FIG. 1-10
FIG. 1-11
FIG. 1-12
FIG. 1-13

TXG237
10
(8) Keep inflammables away from the engine during
operation. Especially during stationary operation
do not operate the engine at high speeds so as
not to set fire to grass or straw with a heated ex-
haust pipe or exhaust fumes.
(9) When you have to operate the tractor at night,
make sure of the location of the controls. If not,
the tractor might work unexpectedly by mistake.
■
LOADING ONTO OR UNLOADING FROM A TRUCK
(1) When loading the tractor onto a truck or a trailer,
turn off the truck’s engine and apply the parking
brakes to the truck or the trailer.
Otherwise, the truck could move and the tractor
fall to the ground.
(2) Pay sufficient attention to the safety conditions
around the tractor and have it guided by someone
to assist the operation. Never allow other persons
to approach the tractor, especially in front of or
behind it.
(3) When loading or unloading the machine on/off
a truck, set slip-proof ramps at the same angles
and drive the tractor straight at sufficiently slow
speeds. Loading the tractor in reverse travel and
unloading it in forward travel.
(4) Never depress the brake pedals during loading or
unloading operation, or the tractor may shift side-
ways, which may cause it to fall off the ramps.
(5) If the engine stalls unexpectedly on the ramps,
depress the brake pedals immediately and roll
the tractor to the ground by manipulating the
brake pedals. Start the engine on the ground and
try again.
(6) When the machine is loaded on the truck, stop
the engine, apply parking brakes, and withdraw
the starter key, chock the wheels, and rope it se-
curely to the truck. During transportation, do not
make sharp turns needlessly so as not to shift the
loaded tractor.
FIG. 1-14
FIG. 1-15

SAFETY
11
(7) Use ramps with the same or better specifications
mentioned below. When the machine is equipped
with attachments other than those included in the
specifications mentioned below, ask your Iseki
dealer for advice.
Specifications of the ramps
・Length:
more than 4 times the height of the platform of
the truck
・Width (effective width): more than 35 cm
・Capacity (one ramp): more than 1700 kg
・Ramps should have anti-skid surfaces
(8) Hook the ramps securely on the platform of the
tractor with the top of the ramp level with the
platform.
(9) Always prepare for even the worst, by never al-
lowing other persons near the tractor.
(10) Drive the tractor carefully at the moment the trac-
tor moves from the ramps onto the platform, for it
changes angle abruptly.
■DURING OPERATION
(1) During operation, never allow other persons in
the vicinity of the tractor, because the tractor itself
or flung pieces may cause injury.
(2) Pay attention to safety around the tractor to avoid
injury to bystanders or damage to property.
Especially when operating with other persons,
use the horn to warn them.
(3) When crossing a ditch or a levee or when pass-
ing through soft land, drive the tractor slowly and
straight so that it does not slip or turn over.
(4) Do not touch dangerous parts such as rotating
parts, moving pars, hot parts (muffler, radiator, or
engine, etc.), or electric parts (battery terminals and
other live parts), or you may be injured seriously.
(5) If you use a trailer, use a proper one which suits
your tractor. Using an improper trailer may cause
serious accidents. Never attempt to haul beyond
the tractor’s capacity. If you have a question,
please consult your Iseki dealer.
Follow strictly the instructions outlined in the
operator’s manual of the mounted or trailed ma-
chinery or trailer, and not to operate the combina-
tion tractor – machine or tractor – trailer unless all
instructions have been followed.
more than 4 times
the height of the platform (h)
FIG. 1-16
FIG. 1-17
FIG. 1-18
FIG. 1-19

TXG237
12
(6) When moving the machine toward an implement
for the purpose of installing the implement, never
allow any one to stand in between. When install-
ing the implement on the machine, be prepare
to move away promptly in the event of an emer-
gency. The brakes should be applied securely
during installation.
(7) When front loader is attached, be aware of the
risk of falling object from the loader bucket. Wear
protective headgear such as a helmet.
(8) Though Tractor is primarily used in agriculture,
it may be used occasionally in a forestry appli-
cation. Pay special attention to the identified
below hazards:
・Toppling trees, primarily in case a rear mounted
tree grab-crane is mounted at the rear of Tractor.
・Penetrating objects in the operator’s enclosure,
primarily in case a winch is mounted at the rear of
Tractor. (e.g. snapping of winch cable).
■INSPECTION AND MAINTENANCE
(1) When servicing the tractor or mounting or dis-
mounting an implement, place the tractor on level,
hard ground which is sufficiently illuminated, or
unexpected accidents may occur.
(2) When servicing the tractor, follow the instructions
listed below:
・Stop the engine.
・Apply parking brakes.
・Disengage all PTO.
・Place all gear shift levers in neutral.
・Remove the starter key.
・Lower the implement fully, if equipped.
If not, your hands or clothes may be caught or
sandwiched between.
(3) When servicing the tractor, use proper tools.
Using makeshift tools may lead to injuries or poor
service, which may result in unexpected acci-
dents during operation.
(4) The engine, muffler, radiator, etc. are very hot just
after operation, so wait until they cool down suf-
ficiently to avoid burns.
(5) Never remove the radiator cap while the engine is
hot or running. Wait until the engine cools down
and then relieve the radiator pressure by releas-
ing the radiator cap. Carelessly pouring cooling
water into the heated radiator can cause serious
damage to the radiator and the engine.
Careless removal of the radiator cap can cause
serious injury because of overheated water vapour.
FIG. 1-20

SAFETY
13
(6) Never fit unauthorized implements or attempt
unauthorized modification.
(7) Be sure to reinstall the removed safety covers in
place as exposed dangerous parts may cause
serious injury.
(8) Avoid high-pressure fluids. Escaping fluid under
pressure can penetrate the skin and cause seri-
ous injury, so keep hands and body away from
pin holes and nozzles ejecting such fluids. Be
sure to consult your dealer about the hydraulic
and fuel injection system trouble.
When checking for leaks, use a piece of card-
board or wood without fail.
If any hydraulic fluid is injected accidentally into
the skin, it must be removed within a few hours
by a doctor familiar with this type of injury.
(9) When servicing wheels and tyres, the tractor
and/or implement must be supported on suitable
blocks or stands. Not a hydraulic jack.
Do not attempt to service a tyre unless you have
the proper equipment and experience to perform
the job. Have the work carried out by your Iseki
dealer or a qualified repair service.
When seating tyre beads onto rims, never exceed
the maximum inflation specifications specfied on
the tyre. Inflation beyond this maximum pressure
may brake the bead, or even the rim, with dan-
gerous, explosive force.
If tyres have deep scratches, cuts or punctures,
the respective tyre should be repaired or replaced
by qualified personnel as soon as possible.
Wear suitable protective clothing, gloves, eye/
face protection.
■STORAGE
(1) Never cover a hot machine just after operation
with a tarpaulin or the like, or the heated engine
and related parts may cause a fire.
(2) Before storing the tractor for a long period of time,
disconnect the battery cables to prevent them, in
case they are gnawed by a rat, from causing a
short circuit, which may lead to a fire.
When disconnecting the cables, disconnect the
negative (-) cable first.
(3) Safe storage of dangerous objects
・When storing dangerous implements, take ap-
propriate safety measures to prevent accidents
by covering with tarpaulin.
・Store fuel in a safe place with caution signs such
as “PREVENT FIRE” or “INFLAMMABLE.”
・All inflammables must also be stored in a safe,
fire-resistant location.
FIG. 1-21
FIG. 1-22

TXG237
14
MAINTENANCE OF THE ELECTRIC SYSTEM
■TO MAINTAIN ELECTRIC WIRING
(1) When servicing the electric wiring, stop the engine
without fail. Otherwise your hands or clothes may
be caught in or sandwiched between rotating parts.
(2) Before manipulating electric parts, be sure to
disconnect the earth battery cable (-), or you may
get an electric shock or be injured by sparks.
(3) Loose electric terminals or connectors may not
only lower electrical performance but also cause
short circuit or leakage of electricity, which may
lead to a fire. Promptly repair or replace damaged
wiring.
(4) Remove chaff or dust from the battery, wiring,
muffler, or engine. Otherwise it could result a fire.
■TO HANDLE THE BATTERY
(1) When working around the battery, avoid smoking.
The battery generates explosive hydrogen and
oxygen gases when it is being charged.
Keep the battery away from sparks or open flames.
(2) The battery should be inspected before starting
the engine. Be careful not to touch the electrolyte
when removing the vent plugs. If the battery
electrolyte makes contact with the skin or cloth-
ing, wash it off immediately with water and then
consult a doctor.
(3) When replacing or inspecting the battery, stop the
engine and turn the main switch off, or electrical
parts may be damaged or unexpected accident
may occur. FIG. 1-23

SAFETY
15
(4) When disconnecting the battery cables, discon-
nect the earth cable (-) first without fail. When
connecting the battery cables, connect the posi-
tive cable (+) first. Disconnecting or connecting in
wrong order may lead to a short circuit or sparks.
■TO HANDLE BOOSTER CABLES
When using booster cables, pay attention to the fol-
lowing items for safe operation:
(1) Before connecting cables, remove the vent plugs.
This will lower the force in case of explosion.
(2) Before connecting cables, be sure to stop the en-
gine. Otherwise unexpected accidents may occur.
(3) Use booster cables with sufficient electrical ca-
pacity. A cable of inadequate capacity will cause
generation of heat, which may lead to a fire.
■DISMANTLING AND DISPOSAL
When the machine or its parts completes their use-
ful life, consult your ISEKI dealer for dismantling
and disposal. If you try to dismantle and dispose by
yourself, be ware of the necessity of hazards and
safety precautions.
■SAFETY DECALS
The labels are stuck on the tractor. You should of
course read the safety instructions in the manual.
But never fail to read the labels on the machine
as well.
・The labels should always be clearly seen, that is,
・When they have become dirty, wash them with
soap water and wipe off with soft cloth.
・If any of them are torn or lost, order new labels
from your dealer. Their codes are mentioned in
“SAFETY DECALS AND THEIR LOCATION.”
・A new label should be placed in the same place
where the old one was located.
・When sticking on a new label, clean the place to
bubbles trapped under it.d.
When disconnecting battery cords,
disconnect negative cord first.
When connecting battery cords,
connect positive cord first.
FIG. 1-24
FIG. 1-25

TXG237
16
(4) Hot part warning label
(Code No.1739-904-001-0)
WARNING: HOT SURFACES, RISK OF BURNS
ON HANDS AND FINGRS
Stay clear of the heated parts until they cool
down sufficiently.
(5) Ether label (Code No.1674-904-002-1)
WARNING: RISK OF EXPLOSION
Ether or other starting fluid should never be used
to start engines equipped with glow plugs.
(6) PTO label (Code No.8654-901-002-0)
WARNING: RISK OF ENTANGLEMENT
Stay clear of the PTO shaft while the engine is
running.
■SAFETY DECALS AND THEIR LOCATIONS
(1) Fan warning label (Code No.1705-902-006-0)
WARNING: RISK OF ENTANGLEMENT
Stay clear of the fan while it is turning
(2) Battery disconnecting label
(Code No. 1636-901-022-00)
WARNING: RISK OF ELECTRIC SHOCK
When disconnecting the battery, detach the nega-
tive terminal first and attach the positive terminal
first when connecting the battery.
(3) Belt warning label (Code No.1674-904-008-0)
WARNING: RISK OF ENTANGLEMENT
Stay clear of the belt while it is running
FIG. 1-26
FIG. 1-28
FIG. 1-30
FIG. 1-31
FIG. 1-27
FIG. 1-29

SAFETY
17
(7) Trailer label (Code No.1674-904-004-0)
WARNING: RISK OF OVERTURNING
The rear implement should be installed on the
tractor with an approved drawbar or by using the
lower links of the 3 point hitch.
Use only an implement of proper loading capacity
and weight not exceeding the designed capability
of the tractor.
(8) Radiator label (Code No.1705-902-008-0)
WARNING:HIGH PRESSURE STEAM AND HOT WATER
Never remove the radiator cap during or just after
operation. The water in the radiator is very hot
and highly pressurized, which could cause burns.
(9) Battery label (Code No.1705-904-002-1)
A WARNING: RISK OF EXPLOSION
Keep away from sparks or flames, which could
cause explosion.
B
WARNING: WEAR AN EYE PROTECTION DEVICE
Battery electrolyte (euphoric acid) may cause
blindness. Wear an eye protector to prevent con-
tact with the eyes.
FIG. 1-32
FIG. 1-33
FIG. 1-34
C WARNING: KEEP OUT OF REACH OF CHILDREN
D WARNING: RISK OF BURNS
Battery electrolyte (sulphuric acid) may cause
burns. Avoid contact with skin or clothing. In case
of an accident, flush affected part immediately
with plenty of water.
E WARNING: RISK OF EXPLOSION
Never use the battery with the electrolyte surface
below the”LOWER”limit, or it may explode. Never
replenish exceeding”UPPER” limit or electrolyte
may leak out.
F WARNING: READ OPERATION MANUAL
Read the safety and operating instructions in the
operation manual before operating the tractor.
Take care of handling the battery.
Improper handling may lead to explosion.
Never short the poles.
Charge the battery in a well ventilated place.
(10) Starter warning label
(Code No.1705-902-007-0)
DANGER: RISK OF ELECTRIC SHOCK
Start the engine only from the seat using the key.
(11) Operation caution label
(Code No.1739-904-071-0)
(Code No.1739-904-072-0)
ABC
DEF
FIG. 1-35
FIG. 1-36

TXG237
18
A WARNING: BEFORE OPERATION
Read the safety and operating instructions in the
operation manual before operating the tractor.
B WARNING: BEFORE OPERATION
Read the safety and operating instructions in the
operation manual before operating the tractor.
C WARNING: RISK OF ABRUPT MOVING
Before leaving the tractor unattended, apply the
parking brake, lower the implement, turn off the
engine and remove the starter key to avoid unex-
pected moving of the tractor.
D WARNING:RISK OF INJURY OR DAMAGE
Pay attention to safety around the machine to
avoid injury to bystanders or damage to property.
E WARNING:RISK OF OVERTURNING
Never operate the tractor on a slope of over 10
degrees, or it could overturn.
F WARNING: RISK OF INJURY OR DAMAGE
Never allow other persons to get on the tractor or
the implement,or it could overturn.
(12) Fuel label(Code No.1739-904-004-0)
DANGER:RISK OF EXPLOSION AND BURNS
Use only diesel fuel.
Before replenishing fuel, be sure to stop the
engine and wait until the engine and heated parts
cool down sufficiently. Keep sparks, open flames,
etc.away from the fuel tank. No smoking!
(13) ROPS label(Code No.1674-904-005-0)
WARNING:RISK OF INJURY
Keep the ROPS in the upright position and fasten
the seat belt at all times. Do not jump from the
seat if the tractor starts to overturn, or you could
be crushed under the tractor. The ROPS should
usually be kept in the upright position during
operation.
However, when the ROPS has to be lowered, do
not wear the seat belt and operate the tractor with
extreme caution.
Do not operate the tractor with a damaged or
modified ROPS.
(14) Lead is used in a battey. There is a warining label
on a battry. Do not throw away a battery as the
general garbage.
(Code No.1728-903-003-0)
14-2 CAUTION: Risk of environment.
Throw away a battery properly because lead is
included in a battery. (Do not throw away a bat-
tery as the general garbage.)
FIG. 1-37
FIG. 1-38
FIG. 1-39

SAFETY
19
(3)
(9)
(14)
(11)(11)
(6)
(7)
(13)
(12)
(5)
(2)
(10)
(4)
(8)
(1)
FIG. 1-40