iSolution IR-575S User manual

Professional Intelligent Scanner
IR-575S
User Guide
Professional Entertainment Technology

EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements

IR-575S
1A
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
2.1 Inserting/Exchanging rotating gobos
2.2 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
4.3 Home Position Adjust
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function
5.2 Easy Controller
5.3 iSolution Operation / Universal DMX Controller
5.4 Universal DMX Controller
5.5 DMX512 Configuration
5.6 DMX512 Connection
6. Troubleshooting
7. Fixture Cleaning

IR-575S
2A
1.SafetyInstruction
WARNING
yPleasekeepthisUserGuideforfutureconsultation. If you sell the unit to another
user, be sure that they also receive this user guide.
yUnpackandcheckcarefullythereisnotransportationdamagebeforeusingthe
unit.
yBeforeoperating,ensurethatthevoltage and frequency of power supply match
the power requirements of the unit.
yIt’simportanttogroundtheyellow/greenconductortoearthinordertoavoid
electric shock.
yTheunitisforindooruseonly.Useonlyinadrylocation.
yTheunitmustbeinstalledinalocationwithadequateventilation,atleast50cm
from adjacent surfaces. Be sure that no ventilation slots are blocked.
yDisconnectmainspowerbeforefuse/lampreplacementorservicing.
yReplacefuse/lamponlywiththesametype. Do not use any other type of lamp.
yMakesurethereisnoflammablematerialsclosetotheunitwhileoperatingasit
is fire hazard.
yUsesafetycablewhenfixesthisunit.Don’thandletheunitbytakingitsheadonly,
but always by taking its base.
yMaximumambienttemperatureisTa:40 .Don’t operate it where the
temperature is higher than this.
yUnitsurfacetemperaturemayreach up to 85 . Don’t touch the housing
bare-hand during its operation. Turn off the power and allow about 15 minutes for
the unit to cool down before replacing bulb or serving as the unit could be very
hot.
yIntheeventofseriousoperatingproblem, stop using the unit immediately. Never
try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center. Always use the same type spare parts.
Please read carefully the instruction, which includes important
information about installation
,
o
p
eration and maintenance.
IR-575S
23A
7.FixtureCleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
yCleanwithsoftclothusingnormalglasscleaningfluid.
yAlwaysdrythepartscarefully.
yClean the external optics at least every 20 days. Clean the internal optics at
least every 30/60 days.

IR-575S
22A
6.Troubleshooting
Following are a few common problems that may occur during operation. Here
are some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connect power and mains fuse.
2. Measure the mains voltage on the mains socket.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if it link
properly.
2. If the DMX LED is on and no response to the channel, check the address
settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or
on PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check in the DMX cables run near or run alongside to high voltage cables that
may cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling.
2. Check the LED for the response of the master / slave mode signal.
D. No response to the sound
1. Make sure the unit that does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
3. Sensitivity is too low, check and set it higher.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is
broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the mains voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan.
IR-575S
3A
yDon’tconnectthedevicetoanydimmerpackorpowerpack.
yDonottouchanywireduringoperationashighvoltagemightbecausingelectric
shock.
yTopreventorreducetheriskofelectrical shock or fire, do not expose the unit to
rain or moisture.
yNevertouchbulbwithbarefingersasitisveryhotafterusing.
yHotlampexplosionhazard.Donotopentheunitwithinfiveminutesafter
switching off.
yDonotstartontheunitwithoutbulbenclosureorhousingaredamaged.
yThehousing,thelenses,ortheultravioletfilter must be replaced if they are visibly
damaged.
yDonotlookdirectlyatthe light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure
that the structure to which you are attaching the unit is secure and is able to support
10 times weight of the unit.

IR-575S
4A
2. Technical Specification
Powersupply
- AC 230V/250V~50/60Hz
Fuse:
- T 10A
Lamp
- MSI 575/ HMI 575 GS/ HMQ 575/2
Opticalsystem
- High efficiency optical system
- High quality optical lens and dichroic colors
- Beam angle : 15
Shutter/Dimmer
- Blackout, 0~100 smooth dimming and strobe speed variable (1~16 flashes per
second)
Movement
- Pan: 180°
- Tilt: 70°
Gobo wheel
- 5 rotating interchangeable gobos plus open
- Magnetic position for continuous rotating
- Shaking effect
Color wheel
- 6 colors plus white
- With rainbow effect
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal
DMX controller.
- Two channel mode: 8 or 14 channels.
8 Channels
Channel 1 = Pan Channel 5 = Color
Channel 2 = Tilt Channel 6 = Gobo Rotating
Channel 3 = Shutter/ Shaking Channel 7 = Dimmer
Channel 4 = Gobo Channel 8 = Focus
IR-575S
21A
5.5DMX512Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120
ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug
and plug it in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit
to the input of the next unit. The cable can not branched or split to a `Y` cable.
DMX512 is a very high-speed signal. Inadequate or damaged cables, soldered
joints or corroded connectors can easily distort the signal and shut down the
system.
4. The DMX signal is able to pass through each fixture continuously, so if one fixture
in the chain is out of order, all the fixtures after this point will not be affected.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4/5:
Not used.

IR-575S
20A
14 Channels:
IR-575S
5A
14 Channels:
Channel 1 = Pan Channel 8 = Function
Channel 2 = Pan Fine Channel 9 = Dimmer
Channel 3 = Tilt Channel 10 = Shutter/Shaking
Channel 4 = Tilt Fine Channel 11 = Gobo
Channel 5 = Pan/Tilt Speed Channel 12 = Gobo Rotating
Channel 6 = Movement Macro Channel 13 = Color
Channel 7 = Movement range Channel 14 = Focus
2.1 Inserting/Exchanging rotating gobos
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before!
Open the cover by loosening the fastening screw at the sides of the cover. If you wish
to use other gobo patterns besides the standard gobos, or if the gobos are to be
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and
insert the new gobo. Press the fixation-ring together and insert it in front of the gobo.
CAUTION!
Never unscrew the screws of the rotating gobo as the ball
bearing will otherwise be opened!

IR-575S
6A
2.2BeamAngle
3.Lamp
MSI 575/ HMI 575 GS/ HMQ 575/2
Because of its high internal pressure, there might be a risk that the Discharge
lamp would explode during operation. The lamp emits intense UV radiation which
is harmful to the eyes and skin. The high luminance of the arc can cause severe
damage to the retina if looks directly at the lamp.
1. Always switch off the mains supply and never handle the lamp or luminaries
when it’s hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with
denatured alcohol and wipe it with a lint free cloth before installation.
3. The lamp generates UV radiation. Never operate the lamp without appropriate
shielding.
4. When burning, the lamp operates at high pressure and there is a slight risk of arc
tube rupture. The risk increases with age, temperature and improper handling of
the lamp. Do not use the lamp any longer than its specified life.
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down afte
r
switchin
g
off.
IR-575S
19A
65. 3 DMX512 Configuration
8 Channels:

IR-575S
18A
5.3.1 iSolution Operation
iConsistentDMXconfiguration enable IRock 575S to be linked with iShow and
iMove together and controlled at the same time.
iDMXaddresscanbesetremotelybyiLeadcontroller(pleaserefertotheuser
manual of iLead controller ). No need to calculate the DMX channels of each
fixture in the chain.
iAutomatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
If you use an universal DMX controller to control the units, you have to set DMX
address from 1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
DMX512 address. Once the address has been selected, press and keep ENTER
button pressed up to when the display stops blinking or storing automatically 8
seconds later. To go back to the functions without any change press the MENU
button again.
Please refer to the following diagram to address your DMX512 channel for the first 4
units.
8 Channels
14 Channels󴔻
You have to set the fixture DMX address in 8 channels mode when you use IL-0824
controller. DMX address can be set remotely by IL-0824 controller. No need to
calculate the DMX channels of each fixture in the chain.
Please refer to the following diagram to address your DMX512 channel for the first 4
units.
8 Channels󴔻
IR-575S
7A
5. Turn screws left and remove the cover as the drawing below.
6. Remove old lamp from lamp socket. Hold the new lamp only by its metallic base.
Never touch the glass bulb. Insert the new lamp in the lamp socket.
7. Make sure the lamp is located in the center of the reflector for the best spot.

IR-575S
8A
4.HowToSetTheUnit
4.1ControlPanel
Display
To sh o w the v ari ous m enu a nd th e sel ect ed f u nct ion s .
LED
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button
MENU To select the programming functions
DOWN Togobackwardintheselectedfunctions
UP Togoforwardintheselectedfunctions
ENTER To confirm the selected functions
On/Off
Turns On/Off the power
Fuse
To r e pla ce t he f use
Power
To connect to the mains supply
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and
Mode.
IR-575S
17A
5.1Master/SlaveBuiltInPreprogrammedFunction
By linking the units in master/slave connection, the first unit will control the other
units to give an automatic, sound activated, synchronized light show. This function is
good when you want an instant show. Its DMX input jack will have nothing plugged
into it, and Its master LED will be constantly on and sound LED will flash to the music.
The other units will have to select (slave 1) or (slave 2) mode,
Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led
lights will constantly on.
2-light show
In (slave mode), means the unit works like the master unit and
means 2-light show. In order to create a great light show, you can set
onthesecondunittogetcontrastmovement to each other, even if you have
two units only.
5.2 Easy Controller (Sold Separately)
The easy remote control is used only in master/slave mode. By connecting to the
1/4” microphone jack of the first unit, you will find that the remote control on the first
unit will control all the other units as below.
Built-in lighting shows triggered by Easy Controller:
Stand by Blackout the unit
Function
Strobe
1. Sync. strobe
2.Async. strobe
3.Sound strobe
X/Y moving pattern
selection
( 12 patterns )
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
change.
Mode Sound 1
(LED off )
Sound 2
(LED normal
blinking)
Slow/Sound 3
(LED on)