IULOCK IU-20 User manual

60mm or 70mm
24mm
54mm
60 mm/2-3 /8"
Lock Components
1. Prepare the door and check dimensions
Key
Keypad
LED indicator
Emergency Power Jack
Exterior Assembly
Plastic box
Strike plate
Screw
Latch
Interior Assembly
Mounting Screws
Reset Key
Connector
Interior Cover
Required tools not included
（ ）
Ruler
Philips head screwdriver
Hammer
Chisel
Use template to mark holes Drill two holes Check dimenslons
4.Install the batteries and perform
the door handing process 5.Install the interior cover
feed power cable through hole in knob and guide spindle into handle.
Align the exterior keypad with the bore hole. Feed the power cable through latch.
The spindle on the exterior keypad should be aligned with the hole in the center
of the lat ch. Insert the spindle through this hole as you press the exterior keypad
against the door.
Adjust the latch to the distance you are going to install, 60 or 70mm
(Backset 2-3/8” or 2-3/4”)
Bore 1 diameter
hole for latch
''
Bore 2-1/8
diameter hole
''
Template
Backset
must match lock (2-3/8 or 2-3/4 )
'' ''
2.Install the latch and strike
Install latch Install strike plate
3.Install the exterior keypad and the interior assembly
Setting latch 60MM or 70MM
（ ）
Install the exterior keypad Install the interior assembly Push out the power cable
70 mm/2-3 /4"
+
-
+
-
+
-
+
-
2-1/8''
IULOCK
IU-20 SMART DOOR KNOB
Installation and User Guide
Features
. two ways to access: code or key
.-30 to 80 °C temperature range
. Low power consumption, 4 AA for 2 Years Battery Life or 20,000 times unlock
. Backlit keypad for use in low light environments
. 1 master code and 50 user codes
. Passage mode for hassle-free entry
. Color LED indicator lights up to show when codes and commands have been successfully entered
. Built-in disguise feature to protect your codes from prying eyes
. Low battery warning indication
Programming guide
Indicator light signals and beep
This function is an added security feature which is aimed at preventing passcode theft. With Passcode Disguise, you may enter 40 digits into the keypad.
As long as the correct passcode sequence is entered, regardless of how many digits were entered before or afterwards, the lock will unlock.
For example, if your user passcode is “112256“, you can successfully unlock the lock by entering “xx...xx112256xx...x”(limit 40 digit).
Passcode and Passcode Disguise
. The lock comes preset with default master passcode 123456
. Used to put the lock in programming mode.
. Can unlock the lock
. Must be different from all of the User Codes currently in the lock.
If you forget the master passcode, you can reset the lock to factory
settings,which restores the default master passcode. See Restore
Factory Settings
. The lock comes not preset any User Code
. Used to unlock the lock
. Must be different from the master passcode and other user passcodes
. Up to 50 possible User Codes can be stored in the lock at one time.
Master passcode User passcode
To delete all user codes, including the master code, follow the instructions
below:
1. Use a screwdriver to remove the screws from the interior cover.
2. Remove the cover and find the reset button located on the battery pack.
3. Press and hold the reset button for 7 seconds until long beep are heard. The
master passcode will return to the manufacturer default code ' '.123456
Restore Factor y Settings
Change the master passcode as soon as
posible! Because of the master passcode can unlock the door.
After restore factory ,
7S
Keypad
IULOCK
Check botton
LED indicator
The color of the light indicates & beep ,the status of the lock.
. a correct master passcode or user passcode was entered ,one long beep
. the programming process is complete ,one long beep
. an incorrect master passcode or user passcode was entered,three short beep
. there was an error in programming, three short beep
. red blinking and beep after keypad backlit off indicates critically low battery
Green
Red
Control of the lock is simply 4-16 digit master passcode or 4-16 digit User passcode.
Passcode Disguise
Keyway
Do not pull the power cable too hard
Pay attention to the marking of the square tube "THIS SIDE UP”

Programming
»If you make a mistake during programming,press the check button repeatedly until the keypad lights up. Then start over.
Press Press Press Press
Press
Press
Enter Enter Enter same
Press Press Press Press
Press
Enter Enter
Press Press Press Press
Enter
Φ1inch
1 3 8inch
to
2 1 2inch
- /
- /
2 3 8inch
- /
2 3 4inch
- /
Φ2inch
Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms
and conditions of the warranty, IULOCK extends a lifetime limited mechanical and finish warranty and a one-year
limited electronics warranty to the original consumer user (“Original User”) of our IULOCK brand product
(“Product”) against defects in material and workmanship, as long as the Original User occupies the residential
premises upon which the Product was originally installed.See answers www.iulock.com for specific warranty details
Warranty
Important Safeguards
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user passcode and master passcode.
5. Dispose of used batteries according to local laws and regulations.
This Manufacturer advises that no lock can provide complete security by itself. This lock maybe defeated by forcible or technical means.
or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense.
Builder's hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should
consult a qualified locksmith or other security professional.
WARNING：
Why is it beeping after keypad light off?
The lock doesn't work?
Why can't I open the door?
Why I can open without passcode?
I forgot all my codes.
If none of the above information resolves your issue, please visit our website at: www.iulock.com
The battery may be low. Please replace the battery.
Try replacing the battery or using the USB backup. If the lock still does not work, contact customer support.
You may be waiting too long to open the door. After entering a code, turn the handle to open the door while the lock LED indicator light is green.
Once the LED indicator light is off, the lock will return to locked position immediately.
You maybe open the passage mode, you can pressing any key.
The lock must undergo a hard reset in order to set the master code back to default and erase all other codes. In order to perform a hard reset,
you must have access to the back of the door.
turn off this function by
Troubleshooting
Template
Press Press Press Press
Enter
Press
Press
Enter Enter same
Enter
Press
Press Press Press Press
Enter
Press
Press
Enter Enter same
Enter
Press
Press Press Press Press
Enter
Press Press Press Press
Enter
Press Press
Press Press
www.iulock.com
24hr online service
Press Press
Enter
Press Press
Press Press Press Press
Enter
Press Press