2-3/8" or 2-3/4"1"2-3/8"Lock Components1. Prepare the door and check dimensionsKeyKeypadLED indicator
Emergency Type-C backup
Exterior AssemblyPlastic boxStrike plateScrewLatchInterior AssemblyMounting ScrewsReset KeyConnectorInterior CoverRequired tools （not included）RulerPhilips head screwdriverHammerChiselUse template to mark holesDrill two holesCheck dimenslons4.Install the batteries and performthe door handing process5.Install the interior cover
feed power cable through hole in knob and guide spindle into knob.
Align the exterior keypad with the bore hole. Feed the power cable through latch.The spindle on the exterior keypad should be aligned with the hole in the center of the latch. Insert the spindle through this hole as you press the exterior keypad against the door.
Adjust the latch to the distance you are going to install, 2-3/8" or 2-3/4"(Backset 2-3/8” or 2-3/4”)If the spindle holes of the latch are not aligned, repeat the 2-3/8" and 2-3/4" positions. This will automatically align the latch spindle holes.Bore 1'' diameter hole for latchBore 2-1/8'' diameter holeTemplateBacksetmust match lock (2-3/8'' or 2-3/4'')2.Install the latch and strikeInstall latchInstall strike plate3.Install the exterior keypad and the interior assemblySetting latch（60MM or 70MM）Install the exterior keypadInstall the interior assembly Pull out the power cable 2-3/4"+-+-+-+-2-1/8''IULOCKIU-20 SMART DOOR KNOB Installation and User GuideFeatures. two ways to access: code and key. -22 F to +176 F temperature range. Low power consumption, 4 AA for 2 Years Battery Life or 20,000 times unlock . Backlit keypad for use in low light environments. 1 master code and 50 user codes . Passage mode for hassle-free entry. Color LED indicator lights up to show when codes and commands have been successfully entered. Built-in disguise feature to protect your codes from prying eyes. Low battery warning indication Programming guide Indicator light signals and beep This function is an added security feature which is aimed at preventing passcode theft. With Passcode Disguise, you may enter 40 digits into the keypad. As long as the correct passcode sequence is entered, regardless of how many digits were entered before or afterwards, the lock will unlock.For example, if your user passcode is “112256“, you can successfully Passcode and Passcode Disguise. The master code MUST EXIST and can be modified, but cannot be deleted. . The lock comes preset with default master passcode 123456. Used to put the lock in programming mode.. Can unlock the lock. Must be different from all of the User Codes currently in the lock. If you forget the master passcode, you can reset the lock to factory settings,which restores the default master passcode. See Restore Factory Settings . User codes can be added, modified, deleted.. The lock comes not preset any User Code. Used to unlock the lock. Must be different from the master passcode and other user passcodes. Up to 50 possible User Codes can be stored in the lock at one time.Master passcodeUser passcodeTo delete all user codes, including the master code, follow the instructions below:1. Use a screwdriver to remove the screws from the interior cover.2. Remove the cover and find the reset button located on the battery pack.3. Press and hold the reset button for 7 seconds until long beep are heard. The master passcode will return to the manufacturer default code '123456'.Restore Factory Settings After restore factory , possible! because of the master passcode can unlock the door.Change the master passcode as soon as 7SKeypad
IULOCK
Check bottonLED indicator
The color of the light indicates & beep ,the status of the lock.
. a correct master passcode or user passcode was entered ,one long beep. the programming process is complete ,one long beep. an incorrect master passcode or user passcode was entered,three short beep . there was an error in programming, three short beep. red blinking and beep after keypad backlit off indicates critically low batteryGreenRed
Control of the lock is simply 4-16 digit master passcode or 4-16 digit User passcode.
Passcode DisguiseKeyway
Pay attention toon the spindle "THIS SIDE UP”
Do not pull the power cable too hard
THIS SIDE UP
Unlock with passcodeUnlock with key
Green and one long beep Red and three short beeps
Code correct, you can turn the knob to open the door immediately, and it will be automatically locked later (the automatic locking time depends on the setting of the automatic locking timer, the default is 4 seconds).
The code is incorrect, please re-enter the correct code and press the check button to confirm
Insert the key on the outside keypad and twist. The first quarter turn should be very easy. After that you are retracting the latch by the force you apply with the key.It takes a little bit of effort. Twisting the knob at the same time you are turning the key helps a little too. Note:The mechanical key of this electronic door knob is completely independent, because the knob is relatively heavy, so using the key requires a little more force than the common mechanical lock.
After tightening the 2 fixing screws, the knob should be easily turned by hand. After your hand leaves the inside knob, the inside knob should easily return to the original position. If not, please re-adjust the position of the inside knob and tighten the screw.
M4X10M4X40M4X20
IULOCK
