J D Williams Burleight Bed User manual

BED - BURLEIGH
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly

Safety and Care Advice
Important- Please read these instructions fully before starting assembly
Check you have all the
componentsandtoolslistedon
pages2and3.
Remove all fittings from the
plasticbagsandseperatethem
intotheirgroups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
spacetolayout the partsbefore
starting.
Do not stand or put weight on
theproduct, this could cause
damage.
Assemble the item as close
toitsfinal position (in the same
room) as possible.
Assemble on a soft level
surface to avoiddamagingthe
unit or your floor.
Parts of the assembly will be
easierwith2people.
We do not
recommend the
useofpower
drill/drivers for
inserting screws,
asthiscoulddamagetheunit.
Onlyusehandscrewdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwisethejointsmay be
damaged.
From time to time check that
there are no loose screws on
thisunit.
This product should not be
discarded with household
waste. Take to your local
authority wastedisposalcentre.
Page 1
Dust surfaces with a soft, dry,
lintfree cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
usingasoftlintfree cloth.
Do not use detergents, abrasive
cleaningproducts or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
positionthefurnitureoutof
direct sunlight and away from
direct heat sources such as
radiatorsandfires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objectsonthesurface, always
useprotective mats to avoid
markingthefurnture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
whenassemblycomplete.
Do Not dispose of packaging
untilassemblycomplete.
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler-Usethisruler to help correctly identify the screws
Tools required
Cross headed screwdriver
(medium & large )
SmallHammer
TapeMeasure
Eyeprotection
(when using a
hammer)

Head Board - 1 Pc
JCBC BOLT M6 X 60MM
- 3 Pcs
Components - Panels
1
Center Support x 1 Pc
Right Side Rail - 1 Pc
2 Holes Horizontal Rail x 10 Pcs
2 3
4
5
Components - Fittings
Please check you have all the panels listed below
Important - Arrow indicate finished face
!
Please check you have all the fittings listed below
Note : The quantities below are the correct amount to complete the assembly; In some case more
fittings may be supplied than are required.
A B
M4 - "L" Key
- 1 Pc
C
Page 2
Foot Board - 1 Pc
Left Side Rail - 1 Pc
Support Leg x 3 Pcs
78
M4 x 32mm CBS Screw
- 26 Pcs
D
M5 - "L" Key
- 1 Pc
6
3 Holes Horizontal Rail x 3 Pcs

Exploded View
Page 3
1
2
4
3
5
6
7
6

Assembly Instructions
Step 1
Connect the head board
and foot board to the
both side rail
Secure the left side rail 3in
place with "L" key D
Repeat on the right side rail
4 and foot board 2
1
3
4
3
1
D
D
x1
Step 2
Connect the 3 holes
horizontal rail to center
support and support leg
Secure the 3 holes horizontal
rail 5in place with JCBC bolt
Band "L" key A
Repeat on the other 3 holes
horizontal rail 5
2
Detail-A
Detail-A
B
x3
Detail-B
A
B
A
x1
Detail-B
7
8
5
5
8
7
Page 4

Assembly Instructions
Step 3
C
x6
Connect the 3 holes
horizontal rail to both side
rail
Secure the 3 holes horizontal
rail 5in place with screw C
Repeat on the other 3 holes
horizontal rail 5
Detail-C
Detail-C
C
Step 4
C
x20
Connect the 2 holes
horizontal rail to both side
rail
Secure the 2 holes horizontal
rail 6in place with screw C
Repeat on the other 2 holes
horizontal rail 6Detail-D Detail-D
C
6
6
Page 5
5

Congratulation! Your unit is complete.
Page 6
Notes