J D Williams Langley Hideaway desk User manual

Assembly Instructions - Please keep for future reference
Width - 82.8cm
2 Door Hideaway
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 48.8cm
Height - 74.8cm
Rev A - 14/05/19
024 xx 9431
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Left End Panel
(73.2x48.6cm)
1363
Right End Panel
(73.2x48.6cm)
1364
Shelf
(54.4x33.7cm)
8175
Division
(22.0x32.7cm)
8176
Top
(82.8x48.8cm)
9188
Door Panel x2
(56.8x39.3cm)
1366
Bottom
(79.4x45.1cm)
8172
Plinth
(79.4x6.0cm)
8171
Backrail
(79.4x29.0cm)
8174
Shelf
(76.9x43.5cm)
1365

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some cases more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Bradawl
Eye protection
(when using a
hammer)
Hingeplate x 4
Code 653006000
Screw x 2
Code 690001075
ABC
E
D
I
Wooden Dowel x 2
Code 770001006
G
HJ
Screw x 16
Code 690001008
Metal dowel x 18
Code 760003004
Large cam x 18
Code 760001103
Fully cranked 26mm
hinge x 4
Code 652001120
18mm bolt x 4
Code 700002021
KM
L Bracket x 1
Code 760001901
12mm Screw x 2
Code 690001099
N
Handle x 2
Code 643003506
8mm screw x 4
Code 700003510
Left Bracket x 1
Code 760xx7001
Right Bracket x 1
Code 760xx7001
Right Runner x 1
Code 760xx7001
Left Runner x 1
Code 760xx7001
L1 R1
R2
L2

Exploded View
4
8175
1363
1364
8174
9188
8176
8172
8171
1366
1366
1365

Step 1
Assembly Instructions
5
A
x4
A
A
A
A
8172
A
x4
A
Fitting cams to the
bottom panel.
Insert 4 metal cams
into the bottom panel
.
Note: Ensure cam arrow
points towards the edge
with the hole.
8172
A
Step 2
Fitting cams to the
back rail.
Insert 4 metal cams
into the back rail panel
.
8174
A
A
x2
A
x2
C
x2
Step 3
Fitting cams to the
divider panel.
Insert 2 metal cams
into the divider panel
.
8176
A
Step 4
Fitting cams and
wooden dowels to the
plinth panel.
Insert 2 metal cams
and 2 wooden dowels
into the plinth panel
.
8171
A
A
A
A
A
A
A
8174
8176
A
A
8171
C
C
C

Assembly Instructions
6
Step 5
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
Bradawl
c: Secure hinges to
doors using screws .
G
D
d: Secure handle to
doors using bolts
Repeat on the second
door.
J
I
G
G
x4
D
x8
J
x4
I
x2
1366
1366
1366
1366
I
A
B
C
D
90
Correct
98
Incorrect
G
G
D
D
D
D
J
J

Assembly Instructions
7
Step 7
Step 8
Step 6
Fitting cams and
dowels to shelf panel.
B
B
B
Insert 2 metal dowels
and 2 cams into the
shelf panel
Note: Insert metal
dowels as far as
shown by arrows. Do not
over tighten.
8175
x2
B
8175
B
B
B
A
A
A
A
Fitting dowels, cams
and hinge plates to
the left end panel.
Insert 7 metal dowels ,
2 cams and 2 hinge-
plates to the left end
panel 1363
A
x2
x7
BA
x2
H
H
B
Fitting dowels, cams
and hinge plates to
the right end panel.
Insert 5 metal dowels ,
2 cams and 2 hinge-
plates to the right end
panel 1364
A
H
x2
1363
B
B
B
B
B
A
AH
x5
BA
x2
H
x2
H
B
B
B
1364
B
B
B
B
A
A
H
H

Assembly Instructions
8
1363
Step 9
x1
N
N
N
E
N
x2
D
x1
Attaching the left
bracket to the left end.
Using 2 screws ,
secure the bracket to
the left end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
N
N
N
N
2ND
1ST
Diagram 1
Diagram 2
L1
L1
L1
Diagram 1
Diagram 2
L1
1363
Step 10
E
N
Attaching the right
bracket to the right end.
Using 2 screws ,
secure the bracket to
the right end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
R1
1364
x1
N
x2
D
D
D
x1
R1
R1
2ND
1ST
N
D
N
D
1364

Assembly Instructions
9
B
B
B
B
x4
B
B
Fitting dowels to the
top panel.
Insert 4 metal dowels
into the top panel .
9188
Step 11
Step 12
Step 13
9188
Connect LH and RH
runners to the shelf
panel.
L2
R2
D
D
D
L2
D L2 R2
x6 x1 x1
Using 6 screws
secure the left runner
and the right runner
to the shelf .
Ensure that the wheel on
the runners is to the
back of the shelf.
D
L2
R2
1365
1365
Connect the shelf and
back rail to the end
panel.
Connect the dowels in the
left end panel to
the cams in the shelf
panel and the
back rail .
Turn the cams 180
degrees to lock.
1363
8175
8174
1363
8175
8174

Assembly Instructions
10
Step 15
Connect the left end
panel to the bottom
panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel .
1363
8172
Step 16
1363
Connect the divider
panel to the shelf panel.
Connect the dowels in the
shelf panel to the
cams in the divider panel
.
8175
8176
Turn cams 180 degrees to
lock.
Turn cams 180 degrees to
lock.
Step 14
8175
8176
8172
E
E
x2
E
Secure bottom panel
to division
Important:
You will require
someone to hold
the shelf and
division.
Locate screws through
holes in bottom panel
and screw into
holes in division .
8172
8176
8176
8172
E

Assembly Instructions
11
Step 17
Connect the plinth
panel to the left end.
Connect the metal dowel
in the left end panel
to the cam in the plinth
panel and insert
the wooden dowel into the
pre-drilled hole.
Step 18
IMPORTANT!
An additional person
is required to hold
the plinth panel
in place.
1363
8171
8171
Turn cams 180 degrees to
lock.
8171 1363
Connect the right end
panel to the bottom,
back rail and plinth
panel.
Connect the dowels in the
RH end panel to the
cams in the bottom panel
and the plinth panel
and the back rail
.
Stand the unit upright.
8172
8171
1364
8171
8172
1364
8174
8174

Assembly Instructions
12
Step 20
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Hanging doors
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
AB
1363
Step 19
B
Ensure the underside of screw
B slides into slot on hingeplate.
Diagram 1
B
Hinge correctly attached to
hingeplate.
Diagram 2
B
Hinge incorrectly attached to
hingeplate.
Diagram 3
1366
1364
9188
1363
Attaching top panel
Connect the metal dowel
in the top panel to
the cams in the LH end
and RH end .
Turn cams 180 degrees to
lock.
1363
9188
1364

Assembly Instructions
13
Step 21
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
14
Step 22
Fit the shelf.
Tilt the shelf as
shown and slide onto the
runner brackets.
1365
1365

Assembly Instructions
15
Step 23
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
With help move the
unit into position.
Warning:
2 people required.
Lift with care.
Warning:
M
x1
K
x2
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Always ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)

Notes;

Notes;

Notes;