J D Williams At Home Luxe SOPHIA BLACK GLOSS TALL BOY... User manual

AssemblyInstructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help of have damaged or missing parts, calls the JDW Customer Helpline: 0871 231 2000
DimensionsNo. peopleAssemblyTime
Width: 30cm
Depth: 30cm
Height: 160cm (approx.)
1 Hour
SOPHIA BLACK GLOSS TALL BOY CAT NO: UM230

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
1
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not allow children to climb or hang on the furniture
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type

Upper Left Panel x 1
1Upper Right Panel x 1
2Back Panel x 1
3
Lower Left Panel x 1
4Lower Right Panel x 1 5Lower Back Panel x 1 6
Top Panel x 1
9
Cross Plinth x 1
8
Door x 1
7
Upper Fixed Shelves x 2
10 Fixed Central Panel x 1
11 Lower Adjustable Shelves x 2
12
Base Panel x 1
13
Components - Panels
Please check you have all the panels listed below
2
88.5 x 30 x 1.2cm 88.5 x 30 x 1.2cm 88.5 x 27.5 x 1.2cm
59 x 30 x 1.2cm 59 x 30 x 1.2cm 60 x 28.3 x 0.3cm
56.8 x 27 x 1.5cm 27.5 x 3 x 1.5cm 30 x 30 x 1.5cm
28 x 27.5 x 1.2cm 30 x 30 x 1.5cm 27 x 26.5 x 1.2cm
30 x 30 x 1.5cm

3
Note:
may be supplied than are required.
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
Tools required
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Phillips screwdriver
(medium & large)
Drill
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
Male Camlock x 16 Female Camlocks x 16 30mm Dowels x 18 Hinges x 2
12mm Screw x 12 35mm Screw x 8 Shelf Support x 8
Leg x 4 14mm Screw x 1
J K
Wall Strap x 1
12mm Screw x 8
L
Camlock covers x 4

a: b: c:
a: To move the top panel up
or down, loosen screws
shown and move top panel to
suit
b.To move the top panel in or
out, loosen screws shown
and move top panel to suit.
Retighten screws
C:To move the top panel left
or right, adjust screws
shown.
Adjusting Hinges
Hinge adjustment:
4

5
Assembly Instructions
Step 1
4
5
8
13
4
5
Step 2
1. Into Cross Plinth 8
insert a total of 4 x Dowels
C as shown.
2. Locate Lower Side
Panels 4 and 5 onto
Dowels
8
4 5
1. Into the bottom edge of
Lower Side Panels 4
and 5 insert a total of
4 x Dowels C as shown.
2. Locate Base Panel 13
onto Dowels
3. Connect Panel 13
using 4 x Screws F as
shown
4
5
13
13

6
Assembly Instructions
Step 3
J
J
J
J
4
5
13
4
5
6
Step 4
1. Onto Base Panel 2
install 4 x Legs J as
shown using a total of 8 x
Screws I ( 2 x Screws I
per leg
13
J
II
1. Slide Back Panel 6
into positon as shown
6

7
Assembly Instructions
Step 5
1
2
3
2
10
10
Step 6
Step 7
1.Into Upper Left Side
Panel 1 install 4 x Male
Camlocks A as shown
1.Insert 3 x Dowels C into
Holes shown is Upper
Right Side Panel 2
2. Locate Back Panel 3
onto Dowels
1.Into Upper Right Side
Panel 2 install 4 x Male
Camlocks A as shown
2. Locate 2 x Fixed
Shelves 10 onto Male
Cams
3. Insert 4 x Female
Camlocks into holes
shown in the underside of 2 x
Panels 5 .Use a screw-
driver to turn the Female
Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section
10
1
2
3
2
10

8
Assembly Instructions
Step 8
1
2
310
10
Step 9
3. Insert 4 x Female
Camlocks into holes
shown in the underside of 2 x
Panels 5 .Use a screw-
driver to turn the Female
Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section
10
1. Into Back Panel 3
insert a total of 3 x Dowels
C as shown
2. Connect Side Panel 1
by locating Male
Camlocks into adjacent
holes
3
1
9
11
1. Insert 4 x Male
Camlocks into 1 x
Fixed Shelf 11
2. Insert 4 x Male
Camlocks into 1 x Top
Panel 9
11
9

9
Assembly Instructions
Step 10
1
2
4
5
11
1. Into the bottom edge of
side panels 1 and 2
insert 4 x Dowels C
2. Locate Fixed Shelf 11
onto Dowels
3. Connect Fixed Shelf
using 4 x Screws F
4. Locate Top Panel 9
into position
1
2
9
11
Step 11
4. Insert 4 x Female
Camlocks into holes
shown. Use a screw
-
driver to turn the Female
Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section
12
11
9
11
1. Locate the Upper half
of the structure onto the
Lower as shown. Locate
Male Camlocks into
adjacent holes
2. Insert 4 x Female
Camlocks into holes
shown. Use a screw
-
driver to turn the Female
Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section

10
Assembly Instructions
Step 12
12
12
7
1. Install Door 10 to
Side Panel 8 by
Connecting 2 x Hinges
D to Door 10 using a
total of 4 x Screws
( 2 x Screws E per
Hinge)
2. Connect the hinges to
Side Panel 8 using a
total of 8 x Screws ( 4
x Screws E per Hinge)
To adjust the position of
the door please refer to
the Adjusting Hinges
section
7
5
7
5
Step 13
1. Insert a total of 8 x Shelf
Supports 12 into internal
holes show.
2. Place 2 x Shelves 12
onto supports
12
5
L
L
L
L
3. Cover 4 x Visible
Camlocks as shown using
4 x Stickers L
L

11
Assembly Instructions
Step 14
9
K
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
2. Move the unit into
desired position.
3. Mark the wall with a
suitable scribe the
position of the fixing
hole.
4. Drill hole and insert a
suitable Wall Plug,
Please check the type of wall
you are fixing to and for more
information please see the
guide to wall mounting
& Fixings on the back page
Warning:
Before driling,check
wall for hidden pipes
and cables.
5. Secure the strap to the
wall using a suitable
wall screw
Note: To hide the straps
behind the unit, drill the
holes lower than the top of
the unit
1. To Top Panel 1 fit
1 x Wall strap L as
shown using 1 x Screw
9
HK
Assembly Complete