J D Williams YL069EM User manual

Assembly Instructions - Please keep for future reference
Width - 34.3cm
5 Drawer Narrow Chest
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 33.0cm
Height - 91.2cm
Rev A - 02/04/19
003 xx 9405
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Top (34.3X33.0cm)
5534
Left End Panel
(89.7x32.8m)
0278
Plinth (30.9x7.6cm)
9422
Bottom (30.9x32.7cm)
0274
Right End Panel
(89.7x32.8cm)
0279
Backpanel (83x33.5cm)0982
Draw Front
(30.5x15.7cm)
9387 x5
Drawer Bottom
(28.7x29.8cm)
4883 x5
Left drawer side (30x10cm)
Drawer back (27.6x10cm)
Right drawer side (30x10cm)
622xx7002 x5
624xx7003 x5
623xx7002 x5

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 12
Code 760001103
Metal dowel x 22
Code 760003004
ABC
E
DF
Small cam x 10
Code 760003005
8mm screw x 20
Code 700003510
Panel pin x 24
Code 760001012
Panel pin guide x 1
Code 684004501
Runner x 10
Code 760001040
HJ
9mm bolt x 10
Code 690001078
L
18mm bolt x 10
Code 700002021
M
Handle x 5
Code 643003506 L bracket x 1
Code 760001901
O
12mm screw x 2
Code 690001099
N

Exploded View
4
622xx7002 x5
623xx7002 x5
624xx7003 x5
4883 x5
9387 x5
5534
0274
9422
0278
0279
0282

A
A
A
Step 1
Assembly Instructions
5
B
x4
B
A
x8
Fitting dowels to top
panel.
Step 2
B
B
x8
B
B
5534
B
B
Step 3
A
A
A
A
A
A
A
A
A
Fitting cams to the
bottom and plinth.
Fitting cams and
dowels to the end
panels.
0274
9422
Insert 4 metal dowels
into the top panel 5534
B
a: Insert 2 metal cams
and 4 metal dowels
into left end panel
.
0278
A
A
Insert 4 cams into the
plinth panel
Insert 4 cams into the
bottom panel
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
9422
0274
B
B
0278
0279
A
B
A
x4
A
B
b: Insert 2 metal cams
and 4 metal dowels
into right end panel
.
0279
A
B
B
B
B
B
B
A

Assembly Instructions
6
Step 4
H
E
H
E
Front of Runner
Back of Runner
A
B
H
x10
E
x20
Attaching runners to
the end panels.
Position the runner so
that the second hole
from the front of the
runner lines up with the
pre-drilled hole nearest
to the edge of the panel.
Use screws to secure
the runner.
Slide the runner forward
revealing the back of the
runner. The second hole
to the back of the runner
will now line up with
the second pre-drilled
hole.
E
Front of runner
x10
Left hand side
Right hand side
622xx7002
623xx7002
A
C
C
C
Step 5
B
A
B
x10
B
0279
B
B
9387
A: Insert 2 metal dowels
into the the drawer
fronts .
9387
B
B: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
622xx7002
623xx7002
E
H
0278
H
H
H
H
E
E
E
E
E
E
E
E
E
E
E
H
E
E
H
E
E
H
E
E
H
E
E
H

Assembly Instructions
7
D: Sit drawer bottom
into grooves on the
drawer front. Ensure foil
on the drawer bottom is
facing upwards.
C
E:Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
Ensure drawer sides are
pressed against drawer
front.
Turn cams 180 degrees to
lock.
D
E
F:Attach the handle
to the drawer front using
bolts .
F
9387
9387
9387
L
L
L
M
M
M
x5
L
x10
C: Insert wooden dowels
in drawer back
into holes in
left
right hand
drawer sides.
Right hand side
Left hand side Drawer Back
624xx7003
622xx7002
623xx7002
623xx7002
624xx7003
622xx7002
4883 Foil surface
to this side.
4883
623xx7002
622xx7002

Connect the dowels in
the right end to the
cams in the plinth panel
and bottom panel
.
Connect right end to
the plinth and bottom
panels.
Assembly Instructions
8
Step 6
Step 7
Connect the dowels in
the left end to the
cams in the plinth panel
and bottom panel
.
Turn cam 180 degrees to
lock.
Connect left end to
the plinth and bottom
panel.
0278
9422
0274
0274
0279
9422
Step 8
Ensure plinth is
not overhanging.
Ensure plinth sits
flush.
Connect the dowels in
the top panel to
the left end and
right end
Connect the top panel.
5534
0278
0279
9422
5534
0278
0274
9422
0278
0274
0279
0279

Assembly Instructions
9
Step 10
Step 9
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Measure to
external corners
Squaring up the unit.
IMPORTANT!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Ensure a tape
measure is used
to square unit up.
XX
YY
YY
D
F
D
x24
F
x1
Secure back panel to
the unit.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
XX
0982
0274
0274

Assembly Instructions
10
Fit the drawer.
Stand the unit up.
For this step we
recommend you follow
the helpful hints below.
2nd Hole
J
x10
J
Step 11
Step 12
PULL SLIDING PART OF DRAWER RUNNERS
OUT SO THEY ARE FULLY EXTENDED. LOCATE DRAWER ONTO RUNNERS
WHILST KEEPING RUNNERS EXTENDED.
LINE UP THE FRONT HOLE IN THE DRAWER SIDE WITH THE 2ND THREADED
HOLE IN THE RUNNER.
WHILE PUSHING THE RUNNER AGAINST THE DRAWER SIDE, SCREW THE
BOLT FROM THE INSIDE OF THE DRAWER, THROUGH THE HOLE IN THE DRAWER SIDE
AND INTO THREADED HOLE IN THE RUNNER.
REPEAT ON OPPOSITE DRAWER SIDE
2nd HOLE
C
AB
Fit the drawer
helpful hints.

Assembly Instructions
11
Step 13
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
N
x1
O
x2
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Always ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)

Notes;

Notes;

Notes;