J D Williams 2 Door 1 Shelf Mirrored Robe User manual

Assembly Instructions - Please keep for future reference
Width - 66.8cm
2 Door 1 Shelf Mirrored Robe
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 49.8cm
Height - 179.9cm
Rev B - 15/02/2017
001 xx 4059
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Shelf x 2 (63.4x45.8cm)
9366
Left End Panel
(178.4x48cm)
93679369
Plinth (63.4x9.2cm)
9359
Back Rail (63.4x12.4cm)
8565
Right End Panel
(178.4x48cm)
9368
Backpanel (169.3x64.4cm)9370
Door x 2
(168.4x32.9cm)
Hanging rail (62.9cm Long)
740006003
Top Rail (62.4x6.0cm)
7194
Top (66.8x49.8cm)
9365

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 20
Code 760001103
Metal dowel x 20
Code 760003004
ABC
E
Drill
DF
H
GI
J
Panel pin x 8
Code 760001012
Panel pin guide x 1
Code 684004501
Hanging supports x 2
Code 680006003
Hingeplate x 6
Code 653006000
12mm screw x 4
Code 690001099
12mm screw x 16
Code 690001008
Support bracket x 2
Code 760001901
Bradawl
Straight arm 26mm
hinge x 6
Code 652001128
K
Handle x 2
Code 644004050
L
20mm bolt x 4
Code 700002006
M
Panel Holder x 3
Code 680003505
N
25mm Screw x 2
Code 690001021

Exploded View
4
9366
9366
9369
9369
8565
9370
9359
9367
9368
7194
9365

Assembly Instructions
5
9359
B
B
B
9365
9365
7194
A
Step 1
B
x4
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
B
N
N
N
N
x2
Fitting dowels to top
panel.
Connect the top rail
to the top panel.
Fitting cams to the
plinth and back rail.
Step 2
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
A
x8
A
A
A
8565
A
A
A
A
Insert 4 metal dowels
into the top panel 9365
Using 2 screws secure
the top rail to the
top panel .
9365
7194
A
Insert 4 cams into
the plinth panel 9359
Step 3
A
Insert 4 cams into
the back rail panel 8565
B

Assembly Instructions
6
Step 4
H
x3
F
x2
C
x1
Insert 3 hinge plates
into the left end panel
.
Insert 2 screws through
the holes in the hanging
rail support .
Note: A bradawl may be
required when attaching
the hanging rail support
to create the lower hole.
H
F
C
9367
Fitting hanging rail
support & hingeplates
to right end.
Insert 3 hinge plates
into the right end panel
.
Insert 2 screws through
the holes in the hanging
rail support .
Note: A bradawl may be
required when attaching
the hanging rail support
to create the lower hole.
H
F
C
9368
Step 5
H
H
H
H
H
H
H
x3
F
x2
C
x1
F
F
C
C
9367
9368
Fitting hanging rail
support & hingeplates
to left end.

Assembly Instructions
7
Step 6
Fitting cams & dowels
to the left end panel.
B
x8
A
x2
B
x8
A
x2
Insert 8 metal dowels
and 2 cams into
left end panel
BA
9367
Step 7
B
B
B
B
B
BB
B
B
B
B
B
BB
BB
A
A
Fitting cams & dowels
to the right end panel.
Insert 8 metal dowels
and 2 cams into
right end panel
BA
9368
A
x8
Step 8
Fitting cams the
shelf panels.
Insert 4 cams into the
shelf panel
Repeat on the remaining
shelf panel.
A
9366
9367
9368
A
A
A
A
9366
A
A

Assembly Instructions
8
Step 9
Attach hinges to the
2 doors
A: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
B: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
I
I
Bradawl
C: Secure hinges to
doors using screws .
Repeat on the second
door panel.
I
F
I
x6
F
x12
9369
9369
9369
9369
F
F
F
F
F
F
A
B
C
D
90
Correct
98
Incorrect
I
I
I
D:
Fit 2 bolts through
the pre-drilled holes in
the door
and connect to the handle
.
L
K
9369
L
x4
K
x2

Assembly Instructions
9
Step 10
Connect the dowels in
the left end to the
cams in the plinth ,
the shelves and
the back rail
We recommend that 2
people for this step, to
hold the back rail in
place.
Finished edges to the oor.
Connect left end to
the plinth, shelves and
back rail.
Step 11
9367
9359
9366
8565
Ensure plinth is
not overhanging.
Ensure plinth sits
flush.
9359
9366
9367
Connect right end to
the plinth, shelves and
back rail.
Connect the dowels in
the right end to the
cams in the plinth ,
the shelves and
the back rail
We recommend that 2
people for this step, to
hold the back rail in
place.
9368
9359
9366
8565
8565
9366
9359
9366
8565
9366
9368

Assembly Instructions
10
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
XX
YY
YY
Step 13
Measure to
external corners
Squaring up the unit.
Ensure a tape
measure is used
to square up unit!
Important:
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Step 12
XX
Connect right end and
left end to the top
panel.
Connect the dowels in
the top panel to the
cams in right end
and the left end
9365
9367
9368
9367
9368
9365

Assembly Instructions
11
Step 11
Step 14
Slide back panel into
the unit.
Slide the back panel into
the grooves in the left &
right end panels and the
top panel.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
E
G
E
x8
G
x1
M
x3
E
G
9370
9366
Plain chipboard surface.
9370
Step 15
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves.
Once inserted fully,
tighten the screws in the
stability blocks.
M
9370
M
M
M
M

Assembly Instructions
12
Step 16
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
Locate hanging rail
onto brackets already
attached. The hanging
rail just slots onto the
brackets.
Locate hanging rail
D
x2
J
x4

Assembly Instructions
13
Step 17
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Hanging doors
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
The doors can be fitted
to either side depending
on your preference.
Repeat the process on
the remaining door.
B
B
B
Underside view
Ensure the underside of screw
B slides into slot on hingeplate.
Hinge correctly attached to
hingeplate.
Hinge incorrectly attached to
hingeplate.
Diagram 1
Diagram 2
Diagram 3
A
B

Assembly Instructions
14
Step 18
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)