J D Williams HD349 User manual

464/3944
Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help of have damaged or missing parts, calls the JDW Customer Helpline: 0871 231 2000
Dimensions No. people Assembly Time
Width: 30cm
Depth: 23cm
Height: 52cm (approx.)
30 Mins
HI GLOSS MIRROR UNIT CAT NO: HD349

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers

2
Components -Panels
Please check you have all the panels listed below
123
456
7
49cmx22cm
26.5cmx20cm
24cmx30cm
50cmx30cm
8
49cmx22cm
Tools required
Phillips screwdriver
(medium & large)
Components - Fittings
Note:
may be supplied than are required.
Male Camlocks x 4 35mm Screw x 4 Shelf Support x 4
Camlock covers x 4 12mm Screw x 12 Hinges x 2
C
A
C
B
C
C
C
D
C
E
F G H
Female Camlocks x 4 30mm Dowel x 12
Top Panel x 1 Side Panel x 1 Side Panel x 1
30cmx22cm
Base Panel x 1
24cmx4.5cm
Cross Plinth x 2
49.5cmx29cm
Back Panel x 1
Shelf Panel x 1 Door x 1

3

4
Assembly Instructions
Step 1
Step 2
Inserting Camlocks
Inserting Dowels
1. Into each side of 2 x
Cross Plinths 5
insert a total of
8 x Dowels C as
shown.
2. Locate Side Panels
2 and 3 onto
Dowels to connect to
2 x Cross Plinths 5
Step 3
2
3
5
C
C
C
C
5
C
C
C
C
C
C
C
C
C
C
C
C
3
2
5
5
D
D
D
D
4
C
C
C
C
C
C
C
CD
D
D
D
4
1
A
AA
A
A
A
A
A
1. Into the underside of
Top Panel 1 insert a
total of 4 x Male
Camlocks as shown
1
A
1
5
C
2
5
3
Inserting Dowels
1. Into the bottom edge
of Side Panels 2 and
3 insert a total of 4 x
Dowels C as shown.
2. Connect Base Panel
4 onto Side Panels 2
and 3 as shown using
4 x Screws D
3
2
2
3
C
42
3
D

5
Assembly Instructions
Step 4
Step 5
Step 6
1. Slide Back Panel 3
into positon shown
6
1. Install 4 x Shelf
Supports D as
shown.
2. Fit Shelf 6 on top of
these
C
e
7
6
6
B
B
B
B
B
F
F
1
7
E
E
E
7
EE
EE
For more information refer
to the Using Camlocks
Section
1. Locate Top Panel 1
onto the unit. Ensure
Male Camlocks
properly locate into
adjacent holes
2. Insert 4 x Female
Camlocks B into
holes shown in Side
Panels 2 and 3
Tighten with a Phillips
Screwdriver until joint
is secure
3. Cover Camlocks
with 4 x Camlock
Covers F as shown
3
2
1
B
23
F

Assembly Instructions
Step 6
6
a: To move the top panel up
or down, loosen screws
shown and move top panel to
suit
b.To move the top panel in or
out, loosen screws shown
and move top panel to suit.
Retighten screws
C:To move the top panel left
or right, adjust screws
shown.
To adjust the position
of the door please
follow the below
depending on your
equirements
a: b: c:
1. Connect Hinges G
to 1 x Doors 5 . Use
2 x Screw F per
Hinge. 4 x Screws total.
2. Connect the
base plate of the hinges
to Side panel 4.
Use 4 x Screws F
per Hinge. 8 x Screws
total.
C
H
8
C
F
G
2
C
F
G
G
G
8
H
H
G
G
2

Assembly Instructions
Step 7
1. To mount the unit to the
wall 4 x holes will need to be
drilled.
Note: Please refer to the wall
mounting guide at the back
of this instruction for further
details.
2. With the aid of someone,
lift the unit into the desired
position and mark the
with a suitable scribe. Please
use a spirit lebel to ensure
your marks are level before
any holes are drilled
3. Drill holes and insert 4 x
suitable Wall Plugs,
Please check the type of wall
information please see the
guide to wall mounting
& Fixings on the back page
4. With the aid of someone
else. Hold the unit in position
and using 4 x suitable screws,
attach the unit to the wall.
Assembly Complete
7