J D Williams Westwood Modula Wall Unit User manual

Assembly Instructions - Please keep for future reference
Width - 40.0cm
1 Door Wall Unit
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 34.8cm
Height - 99.8cm
Rev A - 27/06/19
011 xx 9427
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Left Hand End
(96.8x34.6cm)
1500
Shelf x 2
(36.6x30.7cm)
1502
Door Panel
(67x36cm)
1503
Back Panel
(97.8x37.6cm)
1505
Top
(40x34.8cm)
1498
Bottom
(40x34.8cm)
1499
Right Hand End
(96.8x34.6cm)
1501
Rail
(36.6x12.4cm)
1504

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some cases more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Bradawl
Eye protection
(when using a
hammer)
Hingeplate x 2
Code 653006000
Screw x 4
Code 690001075
ABC
E
I
GH
J
Screw x 4
Code 690001008
Fully cranked 26mm
hinge x 2
Code 652001120
Large cam x 16
Code 760001103 Metal dowel x 16
Code 760003004
30mm Wooden dowel x 4
Code 770001006
Panel Holder x 3
Code 680003505

1498
Exploded View
4
1500
1504
1502
1502
1503
1499
1501
1505

Step 2
Assembly Instructions
5
A
x2
B
x6
C
x2
Fitting cams, dowels
and wooden dowels
to the RH end.
Step 1
Fitting cams, dowels
and wooden dowels
to the LH end.
B
B
B
B
B
B
Note: Ensure cam
arrow points towards
the edge with hole.
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
B
A
1501
B
B
B
B
B
B
A
A
Use a hammer
to knock in
wooden dowels
into inner
holes.
C
C
A
x2
B
x6
C
x2
1500
A
A
C
C
Insert cams dowels
and wooden dowels
into the RH end
.
A
B
C
1501

Step 4
Assembly Instructions
6
B
x4
Fitting cams into the
shelf panels and rail.
Step 3
Fitting dowels into the
top panel.
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
B
B
A
x12
B
B
B
AA
A
A
A
A
A
A
Note: Ensure cam
arrow points towards
the edge with hole.
Repeat on both shelf
panels .
A
1498
1502
1504
1502

Assembly Instructions
7
Step 5
Attach hinges
to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
Bradawl
c: Secure hinges to
doors using screws .
G
I
G
G
x2
I
x4
1503
1503
1503
A
B
C
90
Correct
98
Incorrect
G
G
I
I
I
I
I
I

Assembly Instructions
8
Step 6
Secure shelf panels and
rail to the LH end panel.
Locate cams in both shelf
panels and rail
into dowels on the LH end
panel .
Step 7
1502
1502 1504
1500
1502 1504
1500
1502
1502 1504
1501
Secure shelf panels and
rail to the RH end panel.
Locate cams in both shelf
panels and rail
into dowels on the RH end
panel 1 .
1502 1504
1501
Turn cam 180 degrees
to lock
A
Tighten as shown below.
Turn cam 180 degrees
to lock
A
Tighten as shown below.

Assembly Instructions
9
Step 8
Secure top to LH and RH
end panels.
Locate dowels in top panel
to the cams in the LH
and RH end
panels.
Step 9
1501
1498
1500
1498
1500
1501
Slide backpanel
into the grooves in the LH
and RH end
panels and slot in the top
panel .
Insert backpanel.
1498
1500 1501
1501
1500
1505
1505
1498

Assembly Instructions
10
x3
E
Step 11
Step 10
J
J
x4
J
J
J
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves.
Once inserted fully,
tighten the screws in the
stability blocks.
E
1505
Secure the bottom
panel.
Place bottom panel
onto wooden dowels
making sure the grooved
part is to the back panel
. Then using screws
secure the panel in
place.
J
1505
1499 1499
1505
E
GROOVED EDGE
1500
1501
1505
E
E
E
J
Lay the unit on its front
Stand the unit upright

Assembly Instructions
11
Step 12
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Attach Hinge Plares
and Hang door.
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
AB
B
Ensure the underside of screw
B slides into slot on hingeplate.
Diagram 1
B
Hinge correctly attached to
hingeplate.
Diagram 2
B
Hinge incorrectly attached to
hingeplate.
Diagram 3
1503
H
x2
Attach hinge plates to
the end panel.
Instructions show hinge
plates attached to LH End
but can be attached to
RH if chosen.
However this is preferable
per person.
H
H

Assembly Instructions
12
Step 13
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
13
Step 14
This unit is designed to
be fixed to a suitable
wall through the location
holes in back rail .
You will need to pierce
through the back panel
in order to wall mount.
No fixings are provided
as they will need to suit
the wall type.
Please ensure that the
fixings used are
appropriate to your wall
type.
We do not specify exact
location for mounting the
unit, this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
With help move the
unit into position.
Warning:
2 people required.
Lift with care.
Warning:
Please refer to following
page on how to attach
the unit to the wall.
1504

Assembly Instructions
14
A Guide to wall mounting
and fixings.
Make sure that the screws and wall plugs being used are suitable for supporting your unit.
Consult a qualifed tradesperson if you are unsure.
1. General purpose wall plug
3. Cavity Fixing wall plug 4. Cavity Fixing-Heavy Duty wall plug
6. Shield Anchor wall plug - Heavy loads
2. Plasterboard wall plug
5.Hammer Fixing wall plug
Generally aerated blocks
should not be used to
support heavy loads,
this case. For light loads,
general purpose wall
plugs can be used.
For use with
plasterboard
partitions
or hollow wooden
doors.
For use when
heavy loads such
as shelving, wall
cabinets and coat
racks.
For use with
heavier loads
such as TV & HiFi
speakers and
satelite dishes etc.
For use with
plasterboard
partitions
or hollow
wooden doors.
For use with walls stuck
with plasterboard. The
wall rather than the
plasterboard. Always
to the retaining wall.
Types of walls:
Important:
When drilling into walls always check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug if you are not sure.
2: Ensure you use the recommended drill bit to match the wall plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure wall plugs are inserted beyond the
thickness of the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well tted and are a tight t in the drilled hole.If plastic wall plugs are supplied with your
product:These are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for
your wall,seek professional advice. Failure of the product due to using incorrect xings is the responsibility of
the installer.

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)