Jacuzzi Stella User manual

INSTALLATION INSTRUCTIONS
FREESTANDING
BATHS
PD52000D 11/2018
Contents.....................................................................................................................................................1
Safety Instructions. ....................................................................................................................................2
Inspection and Testing. ..............................................................................................................................4
Sub Floor ...................................................................................................................................................4
Deck Mount Faucet Installation..................................................................................................................4
Installation Instructions for 1-Piece Tub with Integral Overow .................................................................4
Installation Instructions for 1-Piece Tub.....................................................................................................5
Overow Drain Hole Cutouts .....................................................................................................................5
Installation Instructions for 2-Piece Tub.....................................................................................................6
Installation Instructions for Remote Blower................................................................................................6
Installation Instructions for 2-Piece Tubs with Whisper+ Technology™ or Heated Soak...........................7
Installation Instuctions for Bianca Whirlpool Drain Installation...................................................................8
Acylic Bathtub Maintenance.......................................................................................................................9
Solid Surface Care and Cleaning Instructions ...........................................................................................9
Notes........................................................................................................................................................10
Warranty Registration Card ..................................................................................................................... 11
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, California 91710

English
Freestanding Baths
Page 2 www.jacuzzi.com Installation Instructions
Safety Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to
codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation
of all Jacuzzi Luxury Bath products. Our warranty does not cover improper installation related problems.
CAUTION: When using this unit, basic precautions should always be performed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
• Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the
manufacturer.
• Never drop or insert any object into any opening.
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING!
Do not permit children to use this unit unless they are closely supervised at all times. Do not use hydromassage bathtub
unless all suction guards are installed to prevent body and hair entrapment. Never operate the hydromassage bathtub if the
suction cover is broken, damaged or missing.
DANGER: RISK OF SEVERE INJURY FROM ELECTRIC SHOCK OR DEATH FROM ELECTROCUTION!
This unit must be connected only to a supply circuit that is protected by a 15 amp ground fault circuit interrupter (GFCI).
Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test
button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate
in this manner, the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a
ground current is owing, indicating a possibility of an electric shock. Do not use this hydromassage bathtub. Disconnect the
hydromassage bathtub and have the problem corrected by a qualied service representative before using.
WARNING: RISK OF ELECTRIC SHOCK!
Connect only to a circuit protected by a ground fault circuit interrupter (GFCI). (For permanently connected units) A green-
colored terminal (or a wire connector) marked “G,” “GR,” “GROUND,” or “GROUNDING”) is provided within the terminal
compartment. To reduce the risk of electric shock, connect the terminal or connector to the grounding terminal of your
electric service or supply panel with a conductor equivalent in size to the circuit conductors supplying the equipment.
CAUTION: This equipment is intended for indoor use only. Install the equipment in accordance with these instructions. Use
supply wires that are suitable for 167°F (75°C), including the temperature rating of the supply conductors to be used. This
unit should be electrically grounded and installed by a licensed contractor, electrician, and plumber. Building materials and
wiring should be routed away from the motor/pump or blower or other heat producing components of this unit. A pressure
wire connector is provided on the exterior of the motor/pump and heater to permit connection of an No. 8 AWG solid copper
bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity, as needed to comply
with local requirements.
Important CSA Safety Instructions (Canadian models only)
When using this electrical equipment, basic safety precautions should always be followed, including the
following:
1. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING! CHILDREN SHOULD NOT USE HYDROMASSAGE
BATHTUB WITHOUT ADULT SUPERVISION.
2. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING! DO NOT USE HYDROMASSAGE
BATHTUB UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
3. WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING THE HYDROMASSAGE
BATHTUB.
4. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING! DO NOT USE DRUGS OR ALCOHOL BEFORE OR
DURING THE USE OF A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
5. WARNING: RISK OF FETAL INJURY! PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A
PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
6. WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING: DO NOT USE A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
7. SAVE THESE INSTRUCTIONS.

English
Freestanding Baths
Installation Instructions www.jacuzzi.com Page 3
WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING!
Do not use a hydromassage bathtub equipped with a heater immediately following strenuous exercise.
WARNING: RISK OF ELECTRICAL SHOCK!
• Do not permit electrical appliances (such as a hair dryer, lamp, telephone, radio or television) within 60˝
(1524 mm) of this hydromassage bathtub.
• Do not operate hydromassage system unless the bathtub is lled with water to at least 1-2˝ (25-51 mm)
above the highest air hole.
• Do not immerse the control panel by overlling the bathtub.
• When cleaning your bathtub, do not use abrasive substances which will damage the bathtub’s surface.
• To prevent discoloration of the acrylic nish, do not ll the bathtub with water in excess of 140°F (60°C).
WARNING: PROLONGED IMMERSION IN HOT WATER MAY INDUCE HYPERTHERMIA!
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body
temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness and fainting. The effects of hyperthermia include:
A. Failure to perceive heat.
B. Failure to recognize the need to exit the bathtub.
C. Unawareness of impending hazard.
D. Fetal damage in pregnant women.
E. Physical inability to exit the bathtub.
F. Unconsciousness resulting in danger of drowning.
WARNING: RISK OF FETAL INJURY!
Pregnant or possibly pregnant women should consult a physician before using a hydromassage bathtub equipped with a
heater.
WARNING: The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia.
People using medications or having an adverse medical history should consult a physician before using a hydromassage
bathtub equipped with a heater.
WARNING: The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia.
People using medications or having an adverse medical history should consult a physician before using a hydromassage
bathtub equipped with a heater.
WARNING: Do not tamper with user-operated controls or such devices.
WARNING: Use this unit only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturers.
WARNING: To avoid injury, exercise caution when entering or exiting the hydromassage bathtub.
WARNING: Do not use hydromassage bathtub unless all suction guards are installed to prevent body and
hair entrapment. Never operate the hydromassage bathtub if the suction cover is broken, damaged or missing.
WARNING: Water temperature in excess of 104°F (40°C) may be injurious to your health. Check and adjust
water temperature before use.
CAUTION: Test the ground fault circuit interrupter protecting this appliance periodically in accordance with
manufacturer’s instructions.
IMPORTANT: Read the complete instructions provided in this manual before beginning installation.
The Company has obtained applicable code (standards) listings generally available on a national basis for products of this
type. It is the responsibility of the installer/owner to determine specic local code compliance prior to installation of the product.
The Company makes no representation or warranty regarding, and will not be responsible for any code compliance. Product
specications are subject to change without notice.
Safety Instructions (Continued)

English
Page 4 www.jacuzzi.com Installation Instructions
Freestanding Baths
Inspection and Testing
Visual Inspection
1Remove the bathtub from the shipping carton. Be careful not to scratch the surface of the bathtub on exposed staples.
Remove the staples or fold them into the carton. Retain the carton until satisfactory inspection of the product has been made.
Do not lift the bathtub by the plumbing at any time; handle by the shell only.
2 Inspect the shell and bathtub components. Should inspection reveal any damage or defect in the nish or visible damage to
any components, do not install the bathtub. Damage or defect to the nish claimed after the bathtub is installed is excluded
from the warranty. Jacuzzi Luxury Bath’s responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier.
3 Refer any claims for damage to the carrier. For denitions of warranty coverage and limitations, refer to the published
warranty information packed with the product.
All bathtub units are factory tested for proper operation and watertight connections prior to shipping. However, the unit must be
retested by the installer prior to installation. Jacuzzi Luxury Bath is not responsible for any defect that could have been discovered,
repaired, or avoided by following this inspection and testing procedure:
1Place the bathtub on a level surface, near appropriate water supply, and water drainage. A driveway is a suitable choice.
2 Seal the drain and overow hole with tape or a stopper and ll the bathtub to the bottom of the overow hole.
3Allow bathtub to stand for 5 minutes.
4Visually inspect all joints for leaks. Do not install the bathtub if leaks are detected.
5Return bathtub to box or otherwise protect from damage until time of installation.
Bathtub Water and Operational Test
Prepare the sub oor for the drain and ensure that the area is level.
1 The drain/overow of the bathtub extends below the bottom of the bathtub. Identify the drawing in the Technical Specications
section that corresponds with your bathtub (available on www.jacuzzi.com).
2 Determine the location of the basin. The oor must be at and level.
3 Make appropriate cuts to the Sub oor to accommodate the drain.
Please refer to the drawing(s) in the Technical Specications section that correspond to your bathtub.
Sub Floor
Faucet elements must be installed in the recommended area (Fig. 1). Please refer to the Technical Specications that correspond
to your bathtub model for the recommended faucet areas. Not all bathtub models are compatible with deck-mounted faucet
installation. Before drilling, position faucet elements to make sure that they do not interfere with other components such as
overow, plumbing, or supply valves. Some bathtub models without the integrated overow may required the Low-Prole Overow
Kit (MU66000) for centerset faucet installation. This kit is included with bathtub
models that require it.
Faucet elements must be attached to a 36” (914 mm) long ½” stainless steel
braided hoses so you can lift the bathtub when needed.
Apply masking tape on the nished side of the bathtub deck prior
to drilling to prevent chipping. Follow the installation instructions
provided by the faucet manufacturer, mark the locations of the faucet
elements on the deck and drill the holes directly on the nished side.
If installing the faucet on the same side
as the overow, make sure there is no
interference between the two before drilling.
Deck Mount Faucet Installation
CAUTION
Recommended Faucet Area
(Refer to Technical Specications that
correspond to your bathtub model)
Fig. 1

English
Freestanding Baths
Installation Instructions www.jacuzzi.com Page 5
1Install the metal drain/waste
tting (supplied with the tub)
into the drain hole as illustrated
(Fig. 2). Ensure that the drain
opening on the waste tting is
situated in the integral overow
channel (Fig. 2).
2Use clear silicone to adhere the
bottom gasket to the underside
of the integral overow channel.
3 Secure the waste tting with
the supplied waste tting nut.
Apply thread sealant to the
threads prior to inserting the
nut. Overtightening the nut
may cause shell damage.
Ensure the drain opening on the waste tting is not exposed after tightening of the nut.
4 Install a PVC thread adaptor (not supplied) to the metal waste tting. This is to provide a PVC to PVC drain adapter
connection protruding from the oor. Water test tting for leaks before installation. NOTE: Use PVC Cement per ASTM D2564
on all PVC joints.
Installation Instructions for 1-Piece Tub with Integrated Overow
TOE-TAP DRAIN COVER
(SUPPLIED)
INTEGRAL OVERFLOW
CHANNEL
DRAIN OPENING
WASTE FITTING
TOP GASKET (SUPPLIED)
WASTE FITTING NUT
(SUPPLIED)
WASTE FITTING
(SUPPLIED)
WASTE FITTING
BOTTOM GASKET
(SUPPLIED)
SILICONE ALL AROUND
1-1/2” FPT TO SLIP
ADAPTER (NOT
SUPPLIED)
INTEGRAL OVERFLOW
CHANNEL
DRAIN
DETAIL
SEE DRAIN DETAIL
Fig 1.
Fig. 2
Installation Instructions for 1-Piece Tub
1Set the tub in its place and position precisely with respect to
the drain-overow location. Verify where the indentation for
the drain is in relation to the drain-overow. Use a marker to
outline the perimeter of the entire tub directly on the oor
(Fig. 3).
2Mark a trough for the overow drain location on the oor.
The drain/overow extends below the bottom of the bath.
The drain/overow requires a cutout of the oor
for providing space to accommodate the extension. Do not
exceed the dimensions of the tub perimeter. When the
above locations have been marked on the oor, remove the
tub, set it aside and continue with the installation process.
3Prepare the drain/overow trough according to the
dimensions shown in the Technical Specications section.
The depth of the trough depends on the vertical extension
of the drain elbow at the bottom of the plumbing below
the oor level. Install the drain/overow according to the
manufacturer’s instructions. Refer also to the Technical
Specications section.
Watertight installation of the drain is the installer’s
responsibility. Drain leakage is excluded from the Jacuzzi
Luxury Bath warranty of this product.
4Before the tub may be secured to the oor, the following
steps must be completed: Place the tub on the oor in
relation to the drain/overow. Place the tub on the oor and
line up with the markings previously made on the oor.
Floor-mounted or wall-mounted faucetry can be used exterior
to the bath, this can be installed after the bath is installed into
the oor.
Clean up debris left over from the construction steps taken thus far. Also, remove the perimeter outline of the template on
5
the oor. Use silicone to attach tub to the sub oor. Make sure the tub is properly oriented according to the drain/overow
end.
A bead of silicone sealant should be applied around the bottom of the tub. Carefully place the tub on the oor in the correct
position and press to the oor. Place weights around the perimeter and allow the adhesive to cure before proceeding.
Silicone
Bottom
View
Side
View
Fig. 2
Units equipped
with Whisper+
Technology
TM
or Heated Soak
only. Refer to
supplied template
for electrical
connection location.
Fig. 3

English
Page 6 www.jacuzzi.com Installation Instructions
Freestanding Baths
Overow Drain Hole Cutouts
Cutout (Fig. 4) Drain Part Number
Linear Drain MF35XXX
Rotary Drain HP55XXX
Avvio Collection Integral
Deep Soak Drain LH33XXX
Slip Cover Drain PG35XXX
Fig. 3
0.63”
(16mm)
0.38”
(9.65mm)
02.5”
(63.5mm)
3.5”
(88.9mm)
MF35
HP55
PG35
SOLID
SURFACE
LH33
3.13” (79.5mm) Minimum
4.75” (120.6mm) Maximum
Set the 2-piece tub in place and position
it precisely with respect to the drain-
overow location. Verify where the
indentation for the drain is in relation
to the drain-overow. Use a marker to
outline the perimeter of the entire tub
directly on the oor (Fig. 5).
Mark a trough for the overow drain
location on the oor. The drain-
oveow extends below the
bottom of the bath. The drain-
overow requires a cutout of the oor
for providing space to accommodate
the extension. Do not exceed the
dimensions of the tub perimeter.
When the above locations have been
marked on the oor, remove the
tub base (skirt), set it aside and
continue with the installation process.
Faucetry is not supplied with the
freestanding bath. To use deck-
mounted faucetry, exible connection
lines that are 72” in length must be
used. These lines need to be installed prior to installating the bath into the skirt.
When installing the faucet on the same side as the overow, make sure there is no interference between the two before
drilling.
Use silicone to attach the tub skirt to the Sub oor. Make sure the tub is properly oriented according to the drain-overow
end. Place the tub skirt on the oor in relation to the drain/overow. Place the tub skirt on the oor an line up with the
markings prevously made on the oor.
Apply silicone to the foam feet or bottom of the adjustable feet. Carefully place the tub into the tub skirt in relation to the
drain/overow. Allow silicone to dry for 24-hours before entering and/or using the tub.
1Fig. 4
Side
Views
Bottom
Views
Silicone Silicone
2
3
4
6
Installation Instructions for 2-Piece Tub
5
7
Fig. 4
Fig. 5

English
Freestanding Baths
Installation Instructions www.jacuzzi.com Page 7
Installation Instructions for Remote Blower
For ease of installation of remote blower and air line ttings, it is recommended there be access to the underside of the bathtub,
either from above or below the sub oor.
Determine the locations for the blower and verify that access to blower and airline ttings will be possible after bathtub is
installed. Blower location must be within 10 feet of the tub with no more than three elbows as illustrated (Fig. 6).
Use 1-1/2” schedule 40 PVC to connect the bathtub to the blower. Pipe connected directly to the blower should be secured
with a stainless steel screw. Do not glue blower to the PVC.
The control cable provided with the tub is 25’ long. Do not wrap the cable along the pipe from blower to bathtub.
Once airline ttings and control cable are connected to the blower, plug the blower into the outlet and test the operation
before completing the installation.
11
2
3
4
PLUMBING CONNECTION
FROM TUB
4” HOLE 4” HOLE
Fig. 5
Fig. 6
After locating the drain alignment kit, electrical, and water supply lines with
the supplied template (Modena™only), use a marker to trace the inside
footprint of the skirt in the location where the bathtub will be placed. Add
silicone only to the bottom of the skirt and place back in the marked
area (Fig. 7).
Install the overow drain kit onto the bathtub with the supplied brass
tailpiece that is included in the drain alignment kit (Modena™only). Be sure
to apply the supplied grease to the end of the tailpiece where it will
connect to the drain alignment kit (Fig. 9).
Place (2) four foot long 2” x 4” wood supports across the top of the skirt.
Position the wood supports evenly over the skirt as illustrated (Fig. 8). They
will support the bathtub during the connection of the water supply lines and
the electrical connection.
Place the bathtub onto the wood supports in the position that it will be
lowered into the skirt (Fig. 9). The wood supports need to be positioned
under the bathtub away from the foam blocks or adjustable brackets. Orient
the bathtub properly with respect to the electrical outlet and the drain. Also,
make sure the drain and overow areas line up with the drain alignment kit.
Connect the exible water supply lines to the faucets if using a deck
mounted faucet. Make certain the valves are in the closed position. Turn on
the water supply and check for leaks at all connections.
Connect the electrical plug to the dedicated GFCI-protected outlet.
Lower the bathtub into place. Three people will be required to lower the
bathtub into the skirt (one person at each end to lift the bathtub, and the
third person to remove the two wood supports from the top of the bathtub
skirt).
Take care not to damage the brass tailpiece while lowering the bathtub into
the skirt (Modena™only).
Turn on power to the dedicated GFCI-protected circuit and check vsystem
operations.
Figure 6
Figure 7
Figure 8
Apply Silicone
2” x 4” Wood
Supports
Faucet Location
(If Applicable)
Electrical
(28” Cord
Included)
Apply
Grease
(Drain
Alignment
Kit Only) Drain
Alignment Kit
(Modena™ Only)
36” Stainless Steel
Supply Lines
(If Applicable)
Installation Instructions for 2-Piece Tubs Equipped with Whisper+ Technology™ or
Heated Soak
Position Bathtub into Skirt
1
2
3
4
5
6
1
2
Fig. 7
Fig. 8
Fig. 9

English
Page 8 www.jacuzzi.com Installation Instructions
Freestanding Baths
1. Using the supplied template, mark
location where the tub is being installed.
Then mark out the drain box as shown
on the template.
2. Cut out the drain box and recess the
box minimum 1-1/2” below the suboor
(Fig. 10).
3. Install the drain alignment kit into the
drain box.
1. Unbox the Linear DWO (MF35) kit and set aside the
following items: drain elbow, drain waste tee, and short
piece of 1-1/2” PVC pipe. These items will not be
needed for the conversion (Fig. 11).
2. Locate the PVC adapter, brass tailpiece and nut from
the drain alignment kit included in your tub. These will
be used for the conversion.
3. Cut the brass tailpiece to 2-3/4” in length. Deburr and
roll the cut edge with a swage tool. Install components
to the brass tailpiece as shown (Fig. 12).
4. Install the Linear DWO with the items from the
direct drain kit included in your tub as shown
(Fig. 13). Make sure to use the drain gasket from
the Linear DWO kit.
5. Glue the brass tailpiece assembly to the direct
drain as shown (Fig. 13).
1. Apply silicone to bottom ange of bath tub skirt. Apply
grease to the brass tailpiece.
2. Carefully lower the bath tub into place. Take care
not to damage the brass tailpiece.
Drain
Alignment
Kit
Fig. 9
Cross-Section View
Subfloor
Subfloor
Drain
Box
1.5”
Linear
Overflow
Elbow
Drain Waste Tee
(Do Not Use)
Drain Gasket
(Keep)
Drain Elbow
(Do Not Use)
1-1/2” PVC Pipe Short
(Do Not Use)
Fig. 10
Standard Linear DWO Installation (Offset Drain MF35XXX)
Linear
Overflow
Elbow
1-1/2” PVC 90°
Elbow SxS
(Included)
Drain Gasket
(Included in
DWO Kit)
Direct Drain
Tee (Included)
Apply
Glue
Here
Fig. 12
Direct Drain Conversion
Apply
Grease
Here
To Direct Drain
Adapter SPG x
Thread (Included
in Drain
Alignment Kit)
2.75”
Brass Tailpiece (Included in
Drain Alignment Kit)
To Direct Drain
Cut 2-3/4” From
Flange & Swage
Brass Nut
(Included
in Drain
Alignment
Kit)
Fig. 11
Installation Instructions for Bianca Whirlpool Drain Installation
Prepare Floor for Bianca Whirlpool Installation
Convert Linear DWO (MF35) to Direct Drain
After Installing the Finished Floor
1
1
1
2
2
3
3
4
5
2
Fig. 10
Fig. 11
Fig. 12
Fig. 13

English
Freestanding Baths
Installation Instructions www.jacuzzi.com Page 9
To clean the bathtub, use a mild Meguiar’s nonabrasive liquid detergent solution. You can protect and restore the luster to a dulled
acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specically designed for use on acrylic nishes.
Never use abrasive household cleaners of any kind on any Jacuzzi Luxury Bath product.
Minor scratches which do not penetrate the color nish can be removed by lightly sanding with #600-grit wet and dry sandpaper.
Restore the gloss using Meguiar’s Mirror Glaze. Major scratches and gouges which penetrate the acrylic surface will require
renishing. Call Jacuzzi Luxury Bath to nd a service agent in your area.
Acrylic Bathtub Maintenance
Cleaning The Bathtub
Surface Repair
Solid Surface Care And Cleaning Instructions
Jacuzzi Luxury Bath solid surface baths are manufactured with non-porous and durable materials that, when properly cared for
and cleaned, resist soil buildup and stains to a great degree. The unique blend of natural and man-made materials, while strong
and beautiful, may contain very slight variances in color and surface texture throughout the tub. This is normal and a result of the
handmade nature of the product. These baths have been engineered to withstand blemishes under normal use in a bathroom
environment. Damage to the bath that results from improper use may void the warranty. Please operate and maintain the bath in
accordance with all use and care instructions outlined in this manual. In the event that damage to the bath such as minor scratching
to the surface is inadvertently incurred, a qualied professional may be able to restore the luster of the nish by lightly bufng out the
imperfection. For recommended professionals, please contact Jacuzzi Luxury Bath.
To ensure proper care, follow these simple steps:
1. First clean with a mild dish soap and warm water; wipe clean with a soft, slightly damp cloth.
2. For more difcult stains such as grease, oil, paint or ink, apply rubbing alcohol; wipe clean with a soft, dry cloth.
3. Avoid abrasive cleansers and solvents, harsh chemicals or those containing lime removal elements. They may damage the
nish and void the warranty.
4. Avoid abrasive scrubbing cloths or pads.
5. Avoid using razor blades or other sharp objects that might scratch the surface.
6. Avoid aftermarket bath products containing any sort of dye.
7. If unsure as to the suitability of a product’s appropriateness for use with these baths, rst test a very small amount of the
product on an inconspicuous area of the bath before using on a visible surface.
For Matte Finish Models (Observe these additional guidelines)
For very difcult stains, Jacuzzi Luxury Bath recommends the following cleansers and materials: Mr. Clean Magic Eraser, Soft
Scrub, Bon Ami or Gray Scotch Brite Pads (DO NOT use Green Scotch Brite Pads).
For Gloss Finish Models (Observe these additional guidelines)
An additional cleaning or polish using granite or high-gloss counter cleaners is an appropriate option. Jacuzzi Luxury Bath
recommends the following cleansers and materials: Counter Magic. Note: Avoid polishing the bath oor as this could result in a
slippery, unsafe surface.

Page 10 www.jacuzzi.com Installation Instructions
Freestanding Baths
English
Notes:

Jacuzzi Luxury Bath 14525 Monte Vista Avenue Chino, California 91710

Español
WARRANTY REGISTRATION CARD
To complete your registration, visit our website at www.jacuzzi.com or ll out and mail this card to the address printed
on the other side within thirty (30) days from date of purchase in order for this warranty to take effect.
Purchaser's Name ______________________
Purchaser's Address ____________________
City __________________ State __ Zip ____
Home Phone:__________________ Cell Phone:
Email:________________________________
Date of Purchase________
Model Name __________________________
Serial Number _________________________
Dealer's Name_________________________
Dealer's Address _______________________
1. How did you rst hear about this Jacuzzi®product?
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe) ______________
2. Who rst gave you specic information about this product (specications, prices, etc.)?
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
3. What was the main reason for purchase?
( ) Styling ( ) Warranty Service ( ) Product Features
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale_______________________
( ) Other _____________________________
4. Who nally decided which product you would buy?
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
5. Who installed? ( ) Already installed/New Home
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other _____________________________
6. What is the current market value of this property?
Please estimate $ _____________________
7. What is the age of the head of the household?Years
8. What other manufacturers did you consider?
( ) Eljer ( ) Lasco ( ) Price Pster ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
( ) Other (Specify) _____________________
9. How long did you shop before purchasing unit?
( ) 1 day ( ) 2 months- 6 months
( ) 2-7 days ( ) 6 months- 1 year
( ) 1 week- 2 weeks ( ) 1 year- 2 years
( ) 2 weeks- 4 weeks ( ) +2 years
( ) 1 month- 2 months
10. Approximately how long have you lived in this home ?
11. Please indicate, approximately, the total annual income of your household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
( ) $40,000 to $49,999 ( ) $150,000 and Above
12. Was your purchase process?
( ) Very easy ( ) Easy ( ) Difcult ( ) Very Difcult
13. How technically aware were you of the patented Jacuzzi®jet system prior to your purchase?
( ) Not aware ( ) Somewhat aware ( ) Very aware
JACUZZI LUXURY BATH
PD52000A
Ninety-Day
Parts Only
Limited Warranty
On
Accessory(ies)