Jadever JC User manual

JC
1
JC User Manual
1. Introduction
This manual contains installation and operation instructions for the JC crane scale. Please read
the manual completely before installation and operation.
2. Precautions
Before using, please check and make sure every part is in good condition. Provided there is
any broken, please inform your dealer
Avoid sudden temperature changes (suitable operating temperature is between -10℃~
40℃.)
Disconnect the power supply when cleaning the scale.
Do not use the scale in the rain or heavily polluted environment.
Never use the crane over the maximum permitted weight, it will cause danger of breaking.
Always make sure that there are no living beings or materials below the load that could
cause injured or damaged.
Service should be performed by authorized personnel only.
3. Dimension
Model A B C D E F G
JC-600
260
195
33
22
515
76
200
JC-1000
260 195 47 34 530 76 200
JC-2000
260 195 47 34 530 76 200
JC-3000
260 195 50 40 547 76 200
JC-5000 260 195 60 48 634 80 220
JC-10000
260 205 70 52 735 90 230

JC
2
4. Specifications & Features
4-1 Specifications
Model
JC-600
JC-1000
JC-2000
JC-3000
JC-5000
JC-10000
Capacity(kg)
600 1000 2000 3000 5000 10000
Division 1 (kg)
0.2 0.5 1 1 2 5
Division 2 (kg)
0.1 0.2 0.5 0.5 1 2
Display
5 digits, 30mm character height, red backlit LED display
Zero Range
100% Capacity
Stabilization time
≤10s
Maximum Safe Load
150% of full scale capacity
Operating Temp.
-10
℃
~ 40
℃
Humidity
30%~90%RH
Power
6V10AH rechargeable battery
Battery life
150 hours(8 hours charging time)
4-2 Features
360°freely swiveling hook
Die-casting aluminum housing with corrosion-proof and antistatic functions
Auto shut off for power saving
Wireless controller as a standard
Anti-collision key design for a better key service time
AT-89 processor and A/D Conversion Technology
Anti-interference design
5. Keyboard
HOLD Hold the current weighing value
SWITCH Choose the division
ZERO Bring display value back to “0” during weighing
6. Operation
6-1 Power on
Press ON/OFF to power on. The display will first show the max capacity and then after 5

JC
3
seconds it will turn back to zero and ready for operation
Note: It is recommended to allow scale 3-5min of warm-up time before starting weighing
operation.
6-2 Zero
Press ZERO to zero the display
6-3 Weighing
Begin with no load on the scale, the display reading zero. Place item(s) to be weighted on the
scale. The display will show the weight
6-4 Tare
Under the weighing mode, place the container on the scale. Press ZERO to tare.
6-5 Battery recharge
The charge lamp turns green from red when the recharging is completed
When the battery indicator is flashing, it means the low battery. Please recharge. However,
the scale can continue to operate for about 5hours without recharge
After the battery indicator is on for several hours without recharge or there is no more power
in the battery, the scale will be powered off automatically.
After recharge, the screen still cannot display, it indicates that either there is difficulty in
battery recharging or a damaged battery. Please contact the service person.
7. Calibration procedure
Note: make sure the standard the weights are available when doing calibration
1. Press ZERO when power on the crane scale, while “SPEN” is displayed on the screen
2. Press ZERO to enter the calibration，while “00000” is displayed on the screen
3. Press HOLD to choose the weighing value, press SWITCH to move the decimal point
Note: It is better to choose the value which is close to the max capacity.
4. Put on the corresponding weight
5. Press ZERO to save
8. Setting mode
1. Press SWITCH when power on the crane, while “ ” is displayed on the screen
2. Press HOLD or SWITCH to shift the sound modes.
0= no sound 1= with sound
3. Press ZERO to move to hold function setting mode, while “ ” is displayed on the screen
4. Press HOLD or SWITCH to shift the hold modes.
0= no hold function 1=with hold function
5. Press ZERO to move to zero function setting mode, while “ ” is displayed on the screen

JC
4
6. Press HOLD or SWITCH to shift the zero modes.
0=zero function is allowed when not stable 1=zero function is not allowed when not stable
7. Press ZERO to move to saving setting, while “ ” is displayed on the screen
8. Press HOLD or SWITCH to shift the saving modes.
0=not save 1=save
9. Press ZERO to restart
9. Option
Controller description
A Choose division
B Hold function
C Zero function
Note: Pull out the aerial when using.