JAI SW-4000T-10GE User manual

Thank you for purchasing this product.
Be sure to read this documentation before use.
This documentation includes important safety precautions and instructions on how to operate the unit. Be sure to read this documentation to ensure
proper operation.
The contents of this documentation are subject to change without notice for the purpose of improvement.
@2023 JAI
User Manual
SW-4000T-10GE
SW-4000T-SFP
3CMOS Prism Line Scan Camera
Document Version: 2.0
Date: 2023-09-13

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Table of Contents
- 2 -
Table of Contents
Table of Contents 2
About Technical Note 6
Notice/Warranty 7
Notice 7
Warranty 7
Certifications 7
CE Compliance 7
FCC 7
Warning 8
KC 8
China RoHS 9
Usage Precautions 10
Notes on Cable Configurations 10
Notes on LAN Cable Connection 10
Notes on SFP+ Module Installation 10
Notes on Attaching the Lens 11
Phenomena Specific to CMOS Image Sensors 11
Notes on Exportation 11
Features 12
Parts Identification 13
①Lens Mount (M52-Mount or F-Mount) 13
②POWER/TRIG LED 14
③DC IN/TRIG Connector (12-Pin Round) 14
④AUX Connector (10-pin) 16
⑤RJ-45 Connector (SW-4000T-10GE) 16
⑥SFP+ Connector (SW-4000T-SFP) 17
⑦Mounting Holes (M4, 6mm Depth) 17
Preparation 18
Step 1: Install the Software (First Time Only) 18
Step 2: Connect Devices 19
①Lens 20

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Table of Contents
- 3 -
②Mounting 20
③LAN Cable (SW-4000T-10GE) 20
➃Network Card (SW-4000T-10GE) 21
⑤DC IN / Trigger IN Connection Cable 21
⑥AC Adapter (Power Supply) 21
⑦SFP+ Module (SW-4000T-SFP) 21
⑧Fiber Optic Cable (SW-4000T-SFP) 22
Step 3: Verify Camera Operation 22
Step 4: Verify the Connection between the Camera and PC 23
Step 4: Configure Basic Settings for the Camera 26
Control via External Triggers 26
Control Without External Triggers 27
Step 6: Adjust the Image Quality 28
Display the Image 28
Configure Basic Settings 29
Step 7: Save the Settings 30
To Save User Settings 30
To Load User Settings 31
Main Functions 32
Basic Function Matrix 32
GPIO (Digital Input/Output Settings) 33
Camera Output Formats 33
Exposure Mode 34
Trigger Control 34
ExposureMode: Off 35
ExposureMode: Timed 36
ExposureMode: TriggerWidth 37
Pixel Sensitivity Correction 38
PRNU Correction (Pixel Gain Correct) 38
DSNU Correction (Pixel Black Correct) 39
Gain Control 40
LUT (Lookup Table) 41
To Use the LUT Function 41

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Table of Contents
- 4 -
LUT Value 41
Gamma Function 42
To Use the Gamma Function 42
Shading Correction 43
To Use the Shading Correction Function 44
Black Level Correction 44
Variable Line Rate 45
Number of Pixels per Line and Line Rate 46
Electronic Shutter 47
ExposureActive Function 47
Color Space Conversion (Color Transformation Control) 48
Test Pattern Function 49
Counter and Timer Control Function 50
Counter Occurrence Diagram 51
Internal Camera Blocks 51
To Use the Counter Function 52
Chromatic Aberration Correction 53
Connecting Rotary Encoders 54
Frame Start Trigger 55
Binning 56
ROI (Regional Scanning Function) 57
Delayed Readout 57
Chunk Data Function 58
Event Control Function 59
Action Control Function 60
Action Control Example 61
PTP (Precision Time Protocol) 62
Noise Reduction Filter Functions 63
Non-Volatile Flash Memory 63
Setting List (Feature Properties) 64
Selector 64
DeviceControl 65
ImageFormatControl 67

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Table of Contents
- 5 -
AcquisitionControl 68
AnalogControl 69
LUTControl 71
ColorTransformationControl 72
DigitalIOControl 73
CounterAndTimerControl 75
EncoderControl 76
Logic Block Control 77
ActionControl 78
EventControl 78
UserSetControl 83
ChunkDataControl 83
TransportLayerControl 86
PulseGenerator 89
Shading 90
Correction 91
Miscellaneous 93
Troubleshooting 93
Power Supply and Connections 93
Image Display 93
Settings and Operations 93
Specifications 94
Package Contents 96
Spectral Response 97
Dimensions 98
SW-4000T-10GE-F 98
SW-4000T-10GE-M52 99
SW-4000T-SFP-F 100
SW-4000T-SFP-M52 101
Comparison of the Decibel Display and Multiplier Display 102
User's Record 103
Revision History 104

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Table of Contents
- 6 -
About Technical Note
Some additional technical information is provided on the JAI website as Technical Notes. In this
manual, if a technical note is available for a particular topic, the above icon is shown. Please refer
to the following URL for Technical notes.
https://www.jai.com/support-software/technical-notes

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Notice/Warranty
- 7 -
Notice/Warranty
Notice
The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan,
and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the
use of its product and assumes no responsibility for any errors which may appear or for damages
resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to
make changes without notice.
Company and product names mentioned in this manual are trademarks or registered trademarks
of their respective owners.
Warranty
For information about the warranty, please contact your factory representative.
Certifications
CE Compliance
As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC
(Electromagnetic compatibility), JAI Ltd., Japan declares that SW-4000T-10GE and SW-4000T-
SFP comply with the following provisions applying to their standards.
EN61000-6-2 (Generic immunity standard part 1)
EN61000-6-3 (Generic immunity standard part 1)
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Notice/Warranty
- 8 -
connected.
lConsult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for FCC
compliance could void the user’s authority to operate the equipment.
KC
제조년월은 제품상자의 라벨을 참조하십시오.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Notice/Warranty
- 9 -
China RoHS
The following statement is related to the regulation on “Measures for the Administration of the
Control of Pollution by Electronic Information Products “, known as “China RoHS“. The table
shows contained Hazardous Substances in this camera.
mark shows that the environment-friendly use period of contained Hazardous Substances is
15 years.
重 要 注 意 事 项
有毒有害物质或元素名称及含量表
根据中华人民共和国信息产业部『电器电子产品有害物质限制使用管理办法』， 本产品《有毒
有害物质或元素名称及含量表》如下．
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
SW-4000T-10GE
SW-4000T-SFP × 〇 〇 〇 〇 〇
〇:表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572-2011规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572-2011规定的限量要求。
环保使用期限
电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外 泄或突
变、电子信息产品用户使用该电子信息产品不会对环境造成严重污染 或对其人身、
财产造成严重损害的期限。
数字「15」为期限15年。

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Usage Precautions
- 10 -
Usage Precautions
Notes on Cable Configurations
The presence of lighting equipment and television receivers nearby may result in video noise. In
such cases, change the cable configurations or placement.
Notes on LAN Cable Connection
Secure the locking screws on the connector manually, and do not
use a driver. Do not secure the screws too tightly. Doing so may
wear down the screw threads on the camera. (Tightening torque:
0.147 Nm or less)
Caution: Secure manually. Do not secure too tightly.
Notes on SFP+ Module Installation
Check the operation manual of the SFP+ module to be used, and attach it or remove it from the
camera. The SFP module can be attached to and removed from the camera only when the
camera is turned off.
Many SFP modules and fiber optic cables are Class 1 laser products. Do not look into connectors
and cables when installing or removing. There is a risk of injury to eyes.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Usage Precautions
- 11 -
Notes on Attaching the Lens
How to Clean a Sensor
Avoiding Dust Particles
When attaching the lens to the camera, stray dust and other particles may adhere to the sensor
surface and rear surface of the lens. Be careful of the following when attaching the lens.
lWork in a clean environment.
lDo not remove the caps from the camera and lens until immediately before you attach the
lens.
lTo prevent dust from adhering to surfaces, point the camera and lens downward and do not
allow the lens surface to come into contact with your hands or other objects.
lAlways use a blower brush to remove any dust that adheres.
lNever use your hands or cloth, blow with your mouth, or use other methods to remove dust.
Phenomena Specific to CMOS Image Sensors
The following phenomena are known to occur on cameras equipped with CMOS image sensors.
These do not indicate malfunctions.
lAliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing
(zigzag distortion) may appear on the monitor.
lBlooming: When strong light enters the camera, some pixels on the CMOS image sensor
may receive much more light than they are designed to hold, causing the accumulated
signal charge to overflow into surrounding pixels. This “blooming” phenomenon can be seen
in the image but does not affect the operation of the camera.
lFixed pattern noise: When shooting dark objects in high-temperature conditions, fixed
pattern noise may occur throughout the entire video monitor screen.
lDefective pixels: Defective pixels (white and black pixels) of the CMOS image sensor are
minimized at the factory according to shipping standards. However, as this phenomenon
can be affected by the ambient temperature, camera settings (e.g., high sensitivity and long
exposure), and other factors, be sure to operate within the camera’s specified operating
environment.
Notes on Exportation
When exporting this product, please follow the export regulations of your country or region.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Features
- 12 -
Features
This camera is a 3CMOS line scan camera using three 4096 pixel line sensors mounted on a
prism, for the R, G and B channels.
SW-4000T-10GE has a 10 Gigabit Ethernet interface. SW-4000T-SFP has a 10GBASE-R
interface that supports 10 Gigabit Ethernet over fiber when an SFP+ module is attached.
Supported output formats include 8-bit or 10-bit RGB, as well as YUV422_8 or YUV422_8_UYVY
color formats.
Features Overview
lPrism technology for superior color quality and better color differentiation.
lPixel size can be switched (7.5 μ m x 7.5 μ m, 7.5 μ m x 10.5 μ m)
lSupports vertical dual-line binning, 2x horizontal binning, or both.
lSW-4000T-SFP: Supports 10GBASE-R
lAttach an SFP+ module to the camera to enable 10 Gigabit Ethernet connection via
fiber optic cable.
lHigh-speed scanning
lMaximum line rate
lPixel format: YUV422(8bit) : 145kHz
lPixel format: RGB(8bit) : 97kHz
lHSI, sRGB, Adobe RGB and XYZ color space conversion.
lSupport for connection of rotary encoders.
lExcellent shock and vibration resistance.
lGenICam compliant.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Parts Identification
- 13 -
Parts Identification
Note: An exterior view of the F-mount model is shown above. See the "Dimensions " section for
exterior views of M52-mount models.
①Lens Mount (M52-Mount or F-Mount) ②POWER/TRIG LED
③DC IN/TRIG Connector (12-Pin Round) ④AUX Connector (10-pin)
⑤RJ-45 Connector (SW-4000T-10GE) ⑥SFP+ Connector (SW-4000T-SFP)
⑦Mounting Holes (M4, 6mm Depth)
①Lens Mount (M52-Mount or F-Mount)
Mount an M52-mount lens or F-mount lens here.
Note: Before mounting a lens, be sure to refer to ①Lens and confirm the precautions for
attaching a lens and the supported lens types.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Parts Identification
- 14 -
②POWER/TRIG LED
Indicates the power or trigger input status.
LED Status
Lit amber
Camera initializing.
SW-4000T-SFP: SFP+ module not inserted. Not compatible SFP+ module inserted.
The Ethernet Link has not been established.
Lit green Camera in operation
Blinking
green
During operation in trigger mode, trigger signals are being input.
Note: The blinking interval is not related to the actual input interval of the external
trigger.
③DC IN/TRIG Connector (12-Pin Round)
Related Setting Items: DigitalIOControl
Connect the cable for a power supply or for DC IN / trigger IN here.
Camera Side: HR10A-10R-12PB (71) (Hirose Electric or equivalent)
Cable Side: HR-10A-10P-12S (Plug) (Hirose Electric or equivalent)
Pin No. Input/Output Signal Description
1 GND
2 Power In DC In DC +10V ~ + 25V
3 GND
4 Reserved
5 In OPT IN1 - Line 5
6 In OPT IN1 +
7 Out TTL OUT 4 Line 12
8 NC
9 Out TTL OUT 1 Line 1
10 In TTL IN 1 Line 4
11 Power In DC In DC +10V ~ + 25V
12 GND

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Parts Identification
- 15 -
Note: The maximum current rating for the power and ground pins is 1.6A per pin pair. If you
are using a power supply whose voltage would create a current flow above this limit in order
to meet the camera’s maximum power consumption (19.3 W), then power must be connected
via both pin pairs.
SW-4000T-10GE can also be powered by PoE (Power over Ethernet).
TTL Signal specification
TTL out signal specification (Typ.) Output voltage: Low 0.0V, High 5.0V
Input/Output current: +/-32mA
TTL in signal specification (Typ.) Input voltage: Low 0.0 ~ 0.8V, High 2.0 ~ 5.5V
Caution: About Opto In: Check the recommended external input circuit diagram (reference
example) and connect correctly. If you connect Opto In 1 and Opto In 2 in reverse, camera
may be damaged.
Recommended External Input Circuit Diagram (Reference Example)

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Parts Identification
- 16 -
④AUX Connector (10-pin)
Connect the cable for DC IN / trigger IN here.
Camera side: Equivalent to Hirose Electronic 3260-10S3(55)
Cable side: Equivalent to Hirose Electronic 3240-10P-C(50)
Pin No. Attribute Name Description
1 Out TTL OUT2 Line 8
2 Out TTL OUT3 Line 9
3 IN TTL_IN2 Line 10
4 N.C
5 GND GND
6 IN TTL_IN3 Line 13
7 N.C
8 N.C
9 GND GND
10 GND GND
⑤RJ-45 Connector (SW-4000T-10GE)
SW-4000T-10GE supports the following Ethernet standards: 1000Base-T, 2.5GBase-T, 5GBase-
T, 10GBase-T
Depending on the Ethernet standard to be used, the cable type and the maximum cable length
are limited. For details, refer to "Step 2: Connect Devices".
A: LINKLED
Indicates the link status of the
network.
B: ACTLED
Indicates the network
communication status
A: LINK
Light off Network Link is not established.
Blinking
green -
slow
1000Base-T Link is established.
(Interval 1sec)
Blinking
green -
fast
2.5GBase-T Link or 5GBase-T Link is
established. (Interval 200 msec)
Lit green 10GBase-T Link is established.
B: ACT
Light off No network communication
Blinking
green
(Tx) Network communication in
progress.
Blinking
yellow
(Rx) Network communication in
progress.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Parts Identification
- 17 -
⑥SFP+ Connector (SW-4000T-SFP)
SW-4000T-SFP supports 10GBASE-R Ethernet standards.
Requirements specification for SFP+ module:
lSupport 10GBASE-R
lSupport Power level 1
Depending on the Ethernet standard to be used, the cable type and the maximum cable length
are limited.
For details, refer to "Step 2: Connect Devices."
⑦Mounting Holes (M4, 6mm Depth)
Use these holes when mounting the camera directly to a wall or other structural system.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Preparation
- 18 -
Preparation
Read this section to learn how the camera connects to devices and accessories. The preparation
process is described below.
1
Step 1: Install the Software (First Time Only)
lInstall the software for configuring and controlling the camera (eBUS SDK for JAI) on the
computer.
2Step 2: Connect Devices
lConnect the lens, cable, AC adapter, computer, and other devices.
3Step 3: Verify Camera Operation
lVerify whether the camera is turned on and ready for use.
4Step 4: Verify the Connection between the Camera and PC
lVerify whether the camera is properly recognized via Control Tool.
5Step 4: Configure Basic Settings for the Camera
lConfigure the Trigger and Exposure settings.
6Step 6: Adjust the Image Quality
lAdjust the Gain, White Balance and Black Level settings, and adjust the image quality.
7Step 7: Save the Settings
lSave the current setting configurations in user memory.
Step 1: Install the Software (First Time Only)
When using the camera for the first time, install the software for configuring and controlling the
camera (eBUS SDK for JAI) on the computer.
Note: When you install eBUS SDK for JAI, eBUS Player for JAI will also be installed.
1. Download the eBUS SDK for JAI from the JAI website (https://www.jai.com/support-
software/jai-software).
2. Install eBUS SDK for JAI on the computer.

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Preparation
- 19 -
Step 2: Connect Devices
SW-4000T-10GE
SW-4000T-SFP
①Lens ②Mounting
③LAN Cable (SW-4000T-10GE) ➃Network Card (SW-4000T-10GE)
⑤DC IN / Trigger IN Connection Cable ⑥AC Adapter (Power Supply)
⑦SFP+ Module (SW-4000T-SFP) ⑧Fiber Optic Cable (SW-4000T-SFP)

SW-4000T-10GE | SW-4000T-SFP | User Manual (2.0) Preparation
- 20 -
①Lens
F-mount or M-52 mount lenses with lens mount protrusions of 13 mm or less can be attached.
Caution: The maximum performance of the camera may not be realized depending on the
lens.
Notes:
The following formula can be used to estimate the focal length.
Focal length = WD / ( 1 + W/w )
WD: Working distance ( distance between lens and object )
W: Width of object
w: Width of sensor (30.72mm)
②Mounting
When mounting the camera directly to other device, use screws that match the mounting holes on
the camera (M4: depth 6mm).
Caution: For heavy lenses, be sure to support the lens itself. Do not use configurations in
which its weight is supported by the camera.
③LAN Cable (SW-4000T-10GE)
Connect a LAN cable to the RJ-45 connector.
lThe camera supports the following Ethernet standards: 1000Base-T, 2.5GBase-T, 5GBase-
T, 10GBase-T
lThe longest cable length varies depending on the type of LAN cable and the Ethernet
standard. Below, the table shows the relationship diagram between LAN cable type and
Ethernet standard. Correctly select the LAN cable type according to the Ethernet standard
to be used.