JAI GO-5000M-USB-UV User manual

User Manual
Thank you for purchasing this product.
Be sure to read this manual before use.
This manual includes important safety precautions and instructions on how to operate the unit. Be sure to read
this manual to ensure proper operation.
The contents of this manual are subject to change without notice for the purpose of improvement.
© 2021 JAI
CMOS Digital Progressive Scan
Monochrome UV Camera Document
Version: 1.0
GO-5000M-USB-UV_Ver.1.0_Feb.2021
GO-5000M-USB-UV

Notice/Warranty/Certifications
3
Calculation of the maximum frame rate
37
Usage Precautions
5
Exposure Mode
38
Features
6
Trigger Control
39
Parts Identifications
7
Normal continuous operation
41
Timed mode
41
Preparation
9
Trigger width mode
42
Preparation Process
9
RCT (Reset Continuous Trigger) mode
43
Step 1:Installing the Software
9
Video Send Mode
45
Step 2:Connecting Devices
10
Multi ROI mode
48
Step 3:Verifying Camera Operation
12
Delayed Readout function
49
Step 4:Verifying the Connection between
Operation and function matrix
48
the Camera and PC
12
Black level control
50
Step 5:Configuring Basic Settings for the Camera
15
Gain control
50
Step 6:Adjusting the Image Quality
16
LUT
53
Step 7:Saving the Settings
18
Gamma
53
Shading Correction mode
54
Main Functions
19
Blemish compensation
54
Digital IN/OUT interface
19
ALC
55
Optical Interface
22
HDR(High Dynamic Range)
56
Opt In Filter Selector function
23
External appearance and dimensions
57
Pulse Generator
24
Spectral response
58
Sensor layout
28
Specifications table
59
Camera output format
28
Appendix
61
Pixel Format
29
User's Record
63
Output timing(Horizontal)
30
Output timing(Vertical)
31
ROI(Region Of Interest) setting
32
Digital ouput Bit allocation
32
Acquisition control
33
Contents
—2 —
GO-5000M-USB-UV

—3 —
Notice
The material contained in this manual consists of information that is proprietary to JAI Ltd.,
Japan and may only be used by the purchasers of the product. JAI Ltd., Japan makes no
warranty for the use of its product and assumes no responsibility for any errors which may
appear or for damages resulting from the use of the information contained herein. JAI Ltd.,
Japan reserves the right to make changes without notice.
Company and product names mentioned in this manual are trademarks or registered
trademarks of their respective owners.
Warranty
For information about the warranty, please contact your factory representative.
Certifications
CE compliance
As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC
(Electromagnetic compatibility), JAI Ltd., Japan declares that GO-5000M-USB-UV comply with
the following provisions applying to their standards.
EN 61000-6-3 (Generic emission standard part 1)
EN 61000-6-2 (Generic immunity standard part 1)
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for FCC
compliance could void the user’s authority to operate the equipment.
GO-5000M-USB-UV

—4 —
Supplement
The following statement is related to the regulation on “Measures for the Administration
of the control of Pollution by Electronic Information Products“ ,known as “China RoHS“.
The table shows contained Hazardous Substances in this camera.
mark shows that the environment-friendly use period of contained Hazardous
Substances is 15 years.
GO-5000M-USB-UV

Usage Precautions
Notes on cable configurations
The presence of lighting equipment and television receivers nearby may result in
video noise. In such cases, change the cable configurations or placement.
Notes on attaching the lens
Avoiding dust particles
When attaching the lens to the camera, stray dust and other particles may adhere
to the sensor surface and rear surface of the lens. Be careful of the following
when attaching the lens.
• Work in a clean environment.
• Do not remove the caps from the camera and lens until immediately before
you attach the lens.
• To prevent dust from adhering to surfaces, point the camera and lens
downward and do not allow the lens surface to come into contact with your
hands or other objects.
•Always use a blower brush to remove any dust that adheres.
Never use your hands or cloth, blow with your mouth, or use other methods to
remove dust.
Phenomena specific to CMOS image sensors
The following phenomena are known to occur on cameras equipped with CMOS
image sensors. These do not indicate malfunctions.
• Aliasing
When shooting straight lines, stripes, and similar patterns, vertical aliasing
(zigzag distortion) may appear on the monitor.
• Blooming
When strong light enters the camera, some pixels on the CMOS image sensor
may receive much more light than they are designed to hold, causing the
accumulated signal charge to overflow into surrounding pixels.This
“blooming” phenomenon can be seen in the image, but does not affect the
operation of the camera.
• Fixed pattern noise
When shooting dark objects in high-temperature conditions, fixed pattern noise
may occur throughout the entire video monitor screen.
• Defective pixels
Defective pixels (white and black pixels) of the CMOS image sensor are
minimized at the factory according to shipping standards. However, as this
phenomenon can be affected by the ambient temperature, camera settings
(e.g., high sensitivity and long exposure), and other factors, be sure to operate
within the camera’s specified operating environment.
Notes on exportation
When exporting this product, please follow the export regulations of your country
or region.
—5 —
GO-5000M-USB-UV

Features
Connection example:
Camera
External Trigger
AC adapter
PoE-compatible switching hub
PC
— 6 —
The GO-5000M-USB-UV is an industrial progressive scan camera equipped with a
1-inch global shutter CMOS image sensor with 5.2 effective megapixels (2560 ×2048).
This CMOS image sensor has sensitivity in the UV region.
The unit is compact and lightweight in design and is equipped with USB3 Vision interface.
Compact and lightweight
The unit’s compact size (approx. 29 ×29 ×41.5 mm, excluding lens mount) and lightweight
design (approx. 46 g) allows for easy assembly and installation.
Feature overview
New Compact and Rugged housing Series, 1” progressive scan camera
Intelligent body design for easy and flexible installation
USB3 Vision (USB 3.0) interface with power-over-USB capability.
Aspect ratio 5:4, 2560(H) x 2048(V) -5.2 million effective pixels
5 μm square pixels
S/N 55 dB with Dark Compression ON
8-bit, 10-bit or 12-bit output
61.9 frames/second with full resolution in continuous operation (8-bit)
Various readout modes, including horizontal and vertical binning
and ROI (Region Of Interest) for faster frame rates
0 dB to +24 dB gain control
10 μs (1/100,000) to 8 seconds exposure control in 1 μs step
Auto exposure control
Timed and trigger width exposure control
RCT trigger mode for specific applications
ALC control with combined function of AGC and auto shutter
HDR (High Dynamic Range) function is available
Various pre-processing circuits are provided
Programmable LUT
Gamma correction (3 steps: 0.45, 0.6 and 1.0)
Blemish compensation
C-mount for lens mount
GO-5000M-USB-UV

Parts Identification
①Lens mount（C-mount）
Mount a C-mount lens, microscope adapter, etc. here.
❖Before mounting a lens, be sure to refer to “Step 2:Connecting Devices” and confirm
the precautions for attaching a lens and the supported lens types.
②USB 3.0 connector
Use a USB 3.0 compatible cable to connect this to a USB port on the computer.
—7 —
GO-5000M-USB-UV

③POWER/TRIG LED
Indicates the power and trigger input status.
LED status and camera status
LED Light Status
POWER/
TRIG LED
（Lit amber）Camera initializing.
（Lit green）Camera in operation.
（Blinking green）During operation in trigger mode, trigger signals are
being input.
❖The blinking interval is not related to the actual input interval of
the external trigger.
④LINK LED
Indicates whether the GigE network connection is established or not.
⑤ACT LED
Indicates the GigE network status.
⑥DC IN/TRIG connector（6-pin round）
Connect the cable for a power supply (optional) or for DC IN / trigger IN here.
—8 —
Pin No. Input/Output Signal Description
1Power In DC In DC 10 V ～25 V
2In Opto In +
3In Opto In -
4Out Opto Out +
5Out Opto Out -
6GND GND
Compatible connectors
Camera side : HR10A-7R-6PB (73） （Hirose Electric or equivalent ）
Cable side : HR10A-7P-6S (plug) (Hirose Electric or equivalent ）
⑦Camera locking screw holes（M3, 3mm depth）
Use these holes mounting the camera directly to a wall or other structural system.
GO-5000M-USB-UV

Preparation
Preparation Process
Step 1 Installing the Software (first time only)
Install the software for configuring and controlling the camera (eBUS SDK for JAI) on the computer.
Step 2 Connecting Devices
Connect the lens, LAN cable, AC adapter, computer, and other devices.
Step 3 Verifying Camera Operation
Verify whether the camera is turned on and ready for use.
Step 4 Verifying the Connection between the Camera and PC
Verify whether the camera is properly recognized via Control Tool.
Step 5 Changing the Camera Settings
Refer to the procedure for changing the output format setting as an example, and change various
settings as necessary.
Step 6 Adjusting the Image Quality
Refer to the procedures for adjusting the gain, white balance, and black level as examples, and adjust
the image quality.
Step 7 Saving the Settings
Save the current setting configurations in user memory.
Step 1: Installing the Software (first time only)
When using the camera for the first time, install the software for configuring and
controlling the camera (eBUS SDK for JAI) on the computer.
❖When you install eBUS SDK for JAI, eBUS SDK for JAI player will also be installed.
Download the eBUS SDK for JAI from the JAI website.
URL https://www.jai.com/support-software/jai-software
Install eBUS SDK for JAI on the computer.
1
2
— 9 —
GO-5000M-USB-UV

Step 2: Connecting Devices
①Lens
・C-mount lenses with lens mount protrusions of 10 mm or less can be attached.
Lens mount protrusion
Lens
10 mm or less
・To prevent vignetting and to obtain the optimal resolution, use a lens that will cover
the image sensor size.
—10 —
・The maximum performance of the camera may not be realized depending on the lens.
・Attaching a lens with a mount protrusion of 10 mm or longer may damage the lens or
camera.
Caution
Model name
GO-5000M-USB-UV Mono 1 inch
12.8mm x 10.24mm (16.392mm diagonal)
Image Sensor
Note
The following formula can be used to estimate the focal length.
Focal length ＝WD /（1 ＋W/w）
WD ：Working distance （distance between lens and object）
W ：Width of object
w：Width of sensor
GO-5000M-USB-UV
①Lens
Camera body
③USB cable
②Direct connection
(or MP-45 tripod
adapter plate)
or
to external trigger
④DC IN / trigger IN
connection cable
⑤AC adapter(not supplied)
(power supply)

—11 —
②Direct connection（or MP-43 tripod adapter plate）
When mounting the camera directly to a wall or other device, use screws that match the
camera locking screw holes on the camera (M3, depth: 3 mm). Use the supplied screws to
attach the tripod adapter plate.
For heavy lenses, be sure to support the lens itself. Do not use configurations in which its weight
is supported by the camera.
Caution
③USB 3.0 cable
Connect a USB cable to the USB 3.0 connector.
④DC IN / trigger IN connection cable
⑤AC adapter (power supply) (if necessary)
Connect the AC adapter and the round connector of the connection cable to the DC IN /
trigger IN connector on the camera.
GO-5000M-USB-UV
The camera is equipped with a USB 3.0 compatible Micro B connector. Although this connector
includes USB 2.0 connectors, the camera does not support use of USB 2.0.
Caution

—12 —
Step 3: Verifying Camera Operation
When power is supplied to the camera while the necessary equipment is connected, the
POWER/TRIG LED at the rear of the camera lights amber, and initialization of the camera
starts.When initialization is complete, the POWER/TRIG LED lights green.
Verify whether power is being supplied to the camera by checking the rear LED.
When properly turned on
Lit green
* For details on how to read the LEDs, see “LED status and camera status” in the “Parts
Identification” section.
Step 4: Verifying the Connection between the Camera and PC
Verify whether the camera is properly recognized via Control Tool.
Connecting the Camera to Control Tool
1Startup eBUS Player for JAI
eBUS Player for JAI startup screen appears.
eBUS Player for JAI
GO-5000M-USB-UV

—13 —
Push Select / Connect button
The connected camera is listed.
Please select one camera.
2Select the camera you want to configure.
eBUS Player for JAI
File Tools Help
Select / Connect Disconnect
IP address
MAC address
GUID
Vendor
Model
Name
Source
Mode
Play Stop
Communication control
Device control
Image stream control
Connection
Acquisition Control
Parameters and Controls
eBUS Player for JAI
Interface Information
Device Information
Available Devices
Intel(R) Ethernet Connection I219-LM XX:XX:XX:XX:XX:XX
Intel(R) Dual Band Wireless-AC 8260 XX:XX:XX:XX:XX:XX
Bluetooth XX:XX:XX:XX:XX:XX
Microsoft Virtual WiFi Miniport Adapter #2 XX:XX:XX:XX:XX:XX
Microsoft Virtual WiFi Miniport Adapter XX:XX:XX:XX:XX:XX
Intel(R) USB 3.0 eXtensible Host Controller
GO-5000M-USB-UV [XXXXXXXXXXXX]
GiGE
Set IP Address… Select from IP Address…
Show unreachable Network Devices
OK Cancel
GO-5000M-USB-UV

—14 —
3Check that the settings of the selected camera are displayed.
Push the Device control button.
The screen shown below will be displayed. In this window you can adjust various
settings of the camera.
This completes the procedure for verifying whether the camera is properly recognized and
whether control and settings configuration are possible.
eBUS Player for JAI
File Tools Help
Select / Connect Disconnect
N/A
N/A
XXXXXXXXXXX
JAI Corporation
GO-5000M-USB-UV
JAI_DEMO
IP address
MAC address
GUID
Vendor
Model
Name
Source
Mode
Play Stop
Communication control
Device control
Image stream control
Stream: 0 images N/A FPS N/A Mbps Display: N/A FPS
Error count: 0 Last error: N/A
Warnings: N/A
Connection
Acquisition Control
Parameters and Controls
DeviceControl
DeviceVendorName
JAI Corporation
DeviceModelName
GO-5000M-USB-UV
DeviceManufactureInfo
See the possibilities
DeviceVersion
XXXXX
DeviceFirmwareVersion
XXXXX
DeviceSerialNumber
XXXXX
DeviceUserID
JAI_DEMO
DeviceTemperature
XXXXX
DeviceReset
ー
ImageFormatControl
WidthMax
2560
HeightMax
2048
Width
2560
Height
2048
Offset X
0
Offset Y
0
BinningHorizontal
1
BinningVertical
1
PixelFormat
Mono8
TestImageSelector
Off
Acquisition Control
AcquisitionMode
Continuous
AcquisitionStart
AcquisitionStop
×
Device Control
Beginner
Visibility
GO-5000M-USB-UV

—15 —
Step 5: Changing the Camera Settings
This section explains how to change settings by describing the procedure for changing the
output format as an example.
Configuring the Output Format
Configure the size, position, and pixel format of the images to be acquired.
The factory settings are as follows. Change the settings as necessary.
Factory default values
Item Default value
ImageFormatControl Width 2560
Height 2048
OffsetX (horizontal position) 0
OffsetY (vertical position) 0
PixelFormat Mono8
* You can specify the image acquisition area. For details, see “ROI (Regional Scanning Function)”.
1Configuring the [Width] of［ImageFormatControl］
By selecting the item of [Width], you can change the value as shown below.
Note
Depending on the setting item, you need to change visibility.
Please switch visibility (Beginner / Expert / Guru) as necessary.
×
DeviceControl
DeviceVendorName
JAI Corporation
DeviceModelName
GO-5000M-USB-UV
DeviceManufactureInfo
See the possibilities
DeviceVersion
XXXXX
DeviceFirmwareVersion
XXXXX
DeviceSerialNumber
XXXXX
DeviceUserID
JAI_DEMO
DeviceTemperature
XXXXX
DeviceReset
ー
ImageFormatControl
WidthMax
2560
HeightMax
2048
Width
2560
Height
2048
Offset X
0
Offset Y
0
BinningHorizontal
1
BinningVertical
1
PixelFormat
Mono8
TestImageSelector
Off
Acquisition Control
AcquisitionMode
Continuous
AcquisitionStart
AcquisitionStop
×
Device Control
Beginner
Visibility
GO-5000M-USB-UV

—16 —
Step 6: Adjusting the Image Quality
Display the camera image and adjust the image quality.
Displaying the Image
Display the image captured by the camera.
When you push [Play] button, the camera image appears in right area.
File Tools Help
Select / Connect Disconnect
N/A
N/A
XXXXXXXXXXX
JAI Corporation
GO-5000M-USB-UV
JAI_DEMO
IP address
MAC address
GUID
Vendor
Model
Name
Source
Mode
Play Stop
Communication control
Device control
Image stream control
Stream: 0 images N/A FPS N/A Mbps Display: N/A FPS
Error count: 0 Last error: N/A
Warnings: N/A
Connection
Acquisition Control
Parameters and Controls
GO-5000M-USB-UV

—17 —
GO-5000M-USB-UV
Adjusting the Gain
Adjusting the Black Level
The gain control uses Analog Base Gain and Digital Gain.
Analog Base Gain can be set at 0dB, +6dB or +12dB.
The digital gain is used for the master gain setting.
For setting the gain,
1. Set analog gain (Select from 0dB, +6dB and +12dB)
2. Set digital gain
The master gain (DigitalAll) can be set x1 (0dB) to x16 (+24dB) against the analog
base gain. The resolution for gain setting is x0.01/step which is 0.05dB to 0.08dB,
depending on the setting value.
The black level can be set in the following range.
GO-5000M-USB-UV: DigitalAll：-256～+255

—18 —
Step 7: Saving the Settings
The setting values configured in the player (eBUS SDK for JAI) will be deleted when the
camera is turned off. By saving current setting values to user memory, you can load and
recall them whenever necessary. You can save up to three sets of user settings in the
camera. (User Set1 to 3)
■To save user settings
1Stop image acquisition.
2Expand [UserSetControl], and select the save destination ([UserSet1] to
[UserSet3]) in [UserSetSelector].
Note
The factory default setting values are stored in [Default] and cannot be overwritten.
Settings can only be saved when image acquisition on the camera is stopped.
Caution
eBUS SDK for
JAI (Player)
一時メモリ
UserSet1
UserSet2
UserSet3
DefaultSet
Working Set
Memory(Flash)
Memory(RAM)
eBUS Player for JAI
3Select [UserSetSave], and click [Execute ‘UserSetSave’ Command].
The current setting values are saved as user settings.
■To load user settings
1Stop image acquisition.
User settings can only be loaded when image capture on the camera is stopped.
2Select the settings to load (UserSet1 to UserSet3) in [UserSetSelector].
3Select [UserSetLoad], and click [Execute ‘UserSetLoad’ Command].
The selected user settings are loaded.
Note
Changes to settings are not saved to the computer (eBUS SDK for JAI).
GO-5000M-USB-UV

—19 —
Main Functions
Digital IN/OUT interface
In the GO-5000M-USB-UV, the digital IN/OUT capability in the software control tool can assign
the necessary signals needed for the system.
Line Selector
In the Line Selector, the following input and output signals can be assigned.
Line Source
Line source signal can be selected from the following table to connect it to the line item
which is selected in the line selector.
Line Mode
Indicates the status of the interface. (Input, Output or Internal)
Line Inverter
Sets the polarity of the selected input or output. (False or True)
Note1: Select and connect the line source signal against the item selected in the line selector.
Line Status
Indicates the status of the selected signal, input or output (True=High or False=Low)
GO-5000M-USB-UV

—20 —
Line Format
Indicates the format of the line item selected in Line Selector.
(No Connect, TTL, LVDS, Opt Coupled or Internal Signal)
Note: In the GO-5000M-USB-UV, TTL and LVDS interface are not equipped.
GO-5000M-USB-UV