JAMEC PEM TDR3000 User manual

TYRE INFLATOR
DIGITAL - TDR3000
OPERATING INSTRUCTIONS
PRODUCT NO.
10.3012 - 500 mm Hose - Hold On Dual Angle Chuck -Tyre Inator Digital - TDR3000
10.3012OS - 500 mm Hose - Hold On Dual Angle Chuck -Tyre Inator Digital - TDR3000
10.3012OS2 - 2700 mm Hose - Clip On Dual Angle Chuck -Tyre Inator Digital - TDR3000
10.3012OS3 - 1800 mm Hose - Clip On Single Angle Chuck -Tyre Inator Digital - TDR3000
COMPLIES WITH
EN12645: 2014*

TYRE INFLATOR
DIGITAL TDR3000
The Jamec Pem TDR Digital Tyre Inator represent quality and guaranteed
accuracy. The classic handheld, slimline design is easy to hold and is
designed to last in rugged workshop environments.
FEATURES
Includes Certicate of calibration
Multi-scale gauge
Large backlit digital display
Accuracy exceeds EC Standards
Auto on upon pressure sensing
Auto off after 9 seconds
Tough die-cast aluminium housing
Wire sheathed hose eliminates kinking
Impact absorbing bumpers
Rubber grip on chuck
MAINTENANCE MONTHLY
Remove the ‘oil’ screw on the side of the gauge and place 2-3 drops of
‘light’ oil into the gauge mechanism.
IMPORTANT
This tyre inator must only be connected to air line systems which have
clean dry air. Any moisture in the air line system may cause damage to
the operation of this tyre inator and void warranty.
Air pre-lters must be used with this inator to ensure product accuracy
and longevity.
OPERATION
TO READ PRESSURE:
Remove tyre valve cap. With clip-on air chuck lever depressed, rmly press
chuck onto tyre valve stem and release lever, ensure that no air leaks.
Check pressure gauge.
Digital - the digital display will activate once the tyre pressure is sensed.
If no pressure is sensed the display will not turn on. Press the tyre inator
lever to add air into the tyre, before reading the pressure.
DIGITAL - the dial gauge will activate once the tyre pressure is sensed. If
no pressure is sensed ,press the tyre inator lever to add air into the tyre,
before reading the pressure.
TO INFLATE:
With clip-on air chuck lever depressed, rmly press chuck onto tyre
valve stem and release lever, ensure that no air leaks. Fully depress the
tyre inator lever for an appropriate period of time and release the lever.
Checkpressure gauge and repeat the procedure until correct pressure level
is achieved.
TO DEFLATE:
With clip-on air chuck lever depressed, rmly press chuck onto tyre valve
stem and release lever, ensure that no air leaks. Depress the tyre inator
lever half way (until air can be heard to be escaping) for an appropriate
period of time and release the lever. Check pressure gauge and repeat the
procedure until correct pressure level is achieved.
SAFETY
Never exceed the maximum pressure of the tyre. Check that the hose and
chuck are in good condition with no damageorcracks. Ensure safe working
environment when using compressed air. Return to authorised service agent
for repair and maintenance.
WARNING
To avoid risk of personal injury, especially to the eyes, face and skin
DONOT direct the air stream at any person, or any part of the body.
Thisequipment is not intended for use by children without adult
supervision. The manufacturer reserves the right to change product
features at any time without notice.
SPECIFICATIONS
Part No. 10.3012 10.3012OS
Operation Inate / deate / measure Inate / deate / measure
Supply pressure max. 200 psi 200 psi
Max. inflation 174 psi 174 psi
Chuck type Hold on Hold on
Chuck style Dual angle Dual angle
Scale psi, kPa, bar psi, kPa, bar
Inlet size 1/4" BSP 1/4" BSP
Hose length 500mm 500mm
Accuracy ± 2 psi @ 25 - 75 psi ± 2 psi @ 25 - 75 psi
Inflation volume L/min 500 L/min @ 188 psi 500 L/min @ 188 psi
Power source 2 x AAA (included) 2 x AAA (included)
Battery life (continuous use) 80 hr 80 hr
Auto off 9 sec 9 sec
Weight .85 kg .85 kg
Advised application Industrial, workshops Industrial, workshops
Packaging Jamec Pem Box Jamec Pem Box
SPECIFICATIONS
Part No. 10.3012OS2 10.3012OS3
Operation Inate / deate / measure Inate / deate / measure
Supply pressure max. 200 psi 200 psi
Max. inflation 174 psi 174 psi
Chuck type Clip on Clip on
Chuck style Dual angle Single straight
Scale psi, kPa, bar psi, kPa, bar
Inlet size 1/4" BSP 1/4" BSP
Hose length 2700 mm 1800 mm
Accuracy ± 2 psi @ 25 - 75 psi ± 2 psi @ 25 - 75 psi
Inflation volume L/min 500 L/min @ 188 psi 500 L/min @ 188 psi
Power source 2 x AAA (included) 2 x AAA (included)
Battery life (continuous use) 80 hr 80 hr
Auto off 9 sec 9 sec
Weight .85 kg .85 kg
Advised application Industrial, workshops Industrial, workshops
Packaging Jamec Pem Box Jamec Pem Box

BATTERY CHANGE
This inator requires 2 x AAA batteries. If the voltage of the batteries fall
below 2.6 volts, the battery icon will ash continuously until it shuts down.
If the voltage of the batteries fall below 2.5 volts, the low “LO” battery icon
appears while the power is on and then shuts down automatically. The
batteries must be changed if the battery icon ashes.
1. Unscrew the battery cap
TDR3OOO
32..0
PSI
Scale
change
button
2. Slide the batteries into the inator with the positive
end facing out of the inator
3. Replace the battery cap carefully and do not over
tighten
SCALE CHANGE
Press and hold the scale change button to activate the display, once the
display is activated press and hold the button for 2 seconds to change the
display scale.

Distributed by
TRADEPEM INDUSTRIAL PTY LTD.
CALIBRATION CERTIFICATE
This Tyre Inator Part Number: 10.3012, 10.30123OS, 10.3012OS2,
10.3012OS3 has been calibrated in its normal working position on test
equipment with an accuracy that is traceable to standards according to:
EN12645: 2014
Serial Number:
Date:
ALLOWABLE TOLERANCE
PSI
± 1.2 Up to and including 58 psi
± 2.3 Between 58 & 145 psi inclusive
± 3.6 Greater than 145 psi
TEST RESULTS
REFERENCE PRESSURE PSI 29.0 58.0 87.0 116.0
DISPLAY PRESSURE PSI
COMPLIES WITH
EN12645: 2014*
* Tyre pressure measuring Instruments, devices for Inspection of pressure and/or
Ination/Deation of tyres for motor vehicles.
IMPORTANT
No responsibility is accepted for incorrect use of this product.