JAMEC PEM TDR4000 User manual

Part No. 11.0723
TDR4OOO
tyre INFLATOR
Instruction Manual
ON
LIGHT
UNIT

2
TDR4000 Automatic
Tyre Inflator
Thank you for selecting this Jamec Pem
TDR4000 Tyre Inator. Please read this manual
before carrying out any installation or service
procedure. This manual is an integral and
essential part of the product, please keep
it away from damp, heat, dust, oils, do not
remove, tear or amend any parts of the manual
for any reason. It must be made available to the
operator and to maintenance personnel, also
to ensure staff training. If you lose or damage
the manual, ask the manufacturer for a copy,
quoting the Part No. The manual must always
remain with the machine, in the event of the
machine being sold, it must be given to the
new user. The manufacturer reserves the right
to change product features at any time without
notice.
IMPORTANT
This tyre inator must only be connected to
air line systems which have clean dry air. Any
moisture in the air line system may cause
damage to the operation of this tyre inator
and void warranty.
Air pre-lters must be used with this inator
to ensure product accuracy and longevity.
Features
■Auto ON, upon air pressure sensing
■Large tilted LCD display with backlight and
90 second auto OFF
■IP rating = IP44
■Multi scale gauge
■Die cast aluminium unit with impact bumper
and lightweight ABS handle and trigger
■Supplied with ofcial calibration certicate
■Wire sheathed hose on ex area of hose to
eliminate kinking
■Lightweight and robust
■Complies with EN12645: 2014*
Operation
■To read pressure:
Remove tyre valve cap.
With clip-on air chuck lever depressed, rmly
press chuck onto tyre valve stem and release
lever, ensure that no air leaks.
Check pressure gauge, the digital display
will activate once the tyre pressure is sensed.
If no pressure is sensed the display will not
turn on. Press the tyre inator lever to add air
into the tyre, before reading the pressure.
■To inflate:
With clip-on air chuck lever depressed,
 rmlypresschuckontotyrevalvestemand
release lever, ensure that no air leaks.
Fullydepressthetyreinatorleverforan
appropriateperiodoftimeandreleasethelever.
Check pressure gauge and repeat the
procedure until correct pressure level is
achieved.
■To deflate:
With clip-on air chuck lever depressed,
rmly press chuck onto tyre valve stem and
release lever, ensure that no air leaks.
Depress the tyre inator lever half way (until
air can be heard to be escaping) for an
appropriate period of time and release the lever.
Check pressure gauge and repeat the
procedure until correct pressure level is
achieved.
Safety
■Never exceed the maximum pressure of
the tyre.
■Check that the hose and chuck are in good
condition with no damage or cracks.
■Ensure safe working environment when
using compressed air.
■Return to authorised service agent for repair
and maintenance.

3
Instruction Manual
Battery Change
This inator requires 2 x AAA batteries. If the
voltage of the batteries fall below 2.6 volts, the
battery icon will ash continuously until it shuts
down. If the voltage of the batteries fall below
1. Remove the impact bumper by pulling it up
from the inator base.
2. Slide battery cap up.
Replace batteries noting polarity
marks (+ or -).
3. Replace the battery cap.
4. Replace impact bumper by pushing over
inator housing making sure to put locating
lugs back into the correct position.
WARNING
To avoid the risk of personal injury, especially to the eyes, face or skin, DO NOT direct the
air stream at any person, or any part of the body. This equipment is not intended for use by
children without adult supervision. The manufacturer reserves the right to change product
features at any time without notice.
2.5 volts, the low “LO” battery icon appears
while the power is on and then shuts down
automatically. The batteries must be changed if
the battery icon ashes.

4
JAM3718
Distributed by
Companion Brands
Bundoora VIC 3083
www.companionbrands.com.au
* Tyre pressure measuring instruments,
devices for inspection of pressure and/or
ination/deation of tyres for motor vehicles.
SPECIFICATIONS
Description Handheld TDR4000
Type of Inator Digital
Reader unit Digital with backlit display
Chuck type Clip on
Chuck style Single straight
Scale 0-12bar, 0-174psi, 0-1200kPa, 0-12kgF
Inlet size ¼" female
Hose length 500mm with swivel (19.7")
Dimensions 235 L x 90 W x 110 Hmm (9.25" L x 3.5" W x 4.3" H)
Weight 0.68 kg (1.5 lbs)
Accuracy +/- 2psi @ 25-75 psi.
Operation Inate, deate, measure
Supply pressure max. 200psi, 1375kPa
Max. ination 174psi
Powered by 2 x AAA Batteries (included)
Battery life (continuous use) 80 hours
Ination ow 1200 L/min @ 1375Kpa(42.4cfm @ 200psi)
IP rating IP44
Auto OFF 90 seconds
Auto ON Upon air pressure sensing
Advised application Industrial, workshops
ALLOWABLE TOLERANCE
BAR
±0.08 up to and including 4 bar
±0.16 between 4 bar and 10 bar inclusive
±0.25 greater than 10 bar
psi
+/-1.2 up to and including 58 psi
+/-2.3 between 58 and 145 psi inclusive
+/-3.6 greater than 145 psi
TEST RESULTS
Reference pressure
BAR PSI
Display pressure
BAR PSI
Calibration Certicate
This Digital Automatic Tyre Inator has been
calibrated in its normal working position on test
equipment with an accuracy that is traceable to
International Standards according to: 86/217/EEC.
Serial Number:
Date: