Jamec pem Pro:x User manual

58.3012 - 20 metre x 10mm (3/8”)

Extreme Ultraex Reinforced Air Hose

58.3023 - 30 metre x 10mm (3/8”)

Extreme Ultraex Reinforced Air Hose

58.3034 - 20 metre x 12mm

Extreme Ultraex Reinforced Water Hose

58.3045 - 30 metre x 12mm

Extreme Ultraex Reinforced Water Hose

Air and Water Hose Reel

Operating Instructions

The Jamec Pem PRO:X Hose Reel has

been manufactured using the highest

quality materials. This multi-purpose hose

reel is suitable for compressed air and

water applications and is ideal for use

around the home, automotive workshop

or industrial site.

FEATURES

• Precision machined brass internal

spindle for strength and reliability. (water

model tted with nylon spindle)

• Adjustable tension control allows for spring

coil tension to be increased or decreased

spring tension.

• Fully enclosed outer case protects hose

and inner drum against dirt and

other contaminants.

• High impact and weather resistant

UV stabilised polypropylene case.

• Stop anywhere locking

• Extreme ultraex reinforced hose braided

hose with an additional 2 metre leader hose.

• Quality brass hose connectors, tap ttings

and water trigger gun included (with water

model only).

• Heavy duty mounting bracket 180°

swivel mount.

• Convenient carry handle located on back of

the case allows easy removal and retting of

the hose reel to the mounting bracket.

PRODUCT IDENTIFICATION

1. Mounting bracket

2. Fully enclosed case

5. Carry handle

6. Brass internal spindle (nylon internal

spindle water model)

7. 2 metre leader hose

8. Hose with adjustable stopper

9. Water gun (with water model only)

9. 4 x M12 (OD) masonry anchors

I NS TALL ATI ON

The JamecPem PRO:X Hose Reel can be

mounted in a vertical position.

1. Chose a location that is near to the water

source or compressed air source.

2. For large areas, place the hose reel at the

centre of the work area.

3. When mounting the hose reel, ensure

there is adequate clearance under the

reel to prevent injury or damage.

4. Mounting bracket must be installed on

a at surface.

Note: It is recommended to install the

mounting bracket 0.8 metre (minimum) above

the oor level.

5. The wall bracket

supplied has 4 x M8

holes. The masonry

anchors supplied

are M12 OD with M8

threads to t into the

wall bracket. If attaching

to masonry, drill 4 x

M12 holes to afx the

masonry anchors,

making sure to locate

the holes in the right

position to match the

wall bracket.

(Fig. 1)

6. Connect the hose reel

to the Mounting Bracket

with the Pivot Pin.

(Fig. 2)

7. Connect the inlet

leader hose to the

source using the

ttings supplied.

Note: Apply thread sealing

tape to all air line and air

hose ttings.

OPE R ATI ON

1. Slowly pull out the hose to the required

length. A ‘click’ noise will be heard. To lock

the reel, allow the hose to retract slowly after

hearing ‘click’.

2. To release the hose, pull out the hose until

you hear a ‘click’, and then allow the hose

to slowly retract while guiding the hose

back into the hose reel. The self layering

mechanism will coil the hose back onto the

inner drum.

3. To avoid injury and damage, always hold the

hose while it is retracting. This hose reel has

a controlled return function which allows the

hose to return slowly if it is let go. It is always

recommended to always hold the hose while

it’s retracting. In the event the hose is let go

this controlled return function will stop the

hose from reacting too fast.

0.8 metre min.

Fig. 1 Mounting Bracket

Fig. 2 Pivot Pin

IMPORTANT:

If the hose becomes tangled and will not retract - slowly pull out the hose past the tangled

section and then allow the hose to slowly retract while guiding the hose back into the hose reel.

Always ensure the hose is clean and not twisted.

ADJUSTING THE STOP-BALL

The location of the hose stopper can be

adjusted to allow more hose or less hose to

be exposed when fully rewound.

1. Pull out the desired length of hose, ensuring

the hose reel is in the lock position.

2. Open the latch on the hose stopper and

move it to the desired position on the hose.

3. Re-latch the hose stopper at desired

position

CAUTION:

Always make sure the hose reel is in the

locked position before removing the hose

stopper and make sure the hose stopper is

securely fastened before unlocking the reel.

ADJUSTING THE

TENSION SPRING

Over time it is natural for the spring to lose

some tension. The tension can easily be

adjusted and tightened to provide years of

service.

CAUTION:

Only adjust the spring when the hose is fully

rewound. Do Not Over-tighten

Using a at head screw driver, remove the

side cover marked “Coil Spring Adjustment”

by prying it open where indicated.

2. Fold out the crank handle.

3. Turn the crank clockwise to increase

the tension, counter clock-wise to reduce

the tension.

4. Turn the crank handle ve times in the

desired direction. Check the spring tension

by pulling a short length of the hose and

letting it rewind.

5. Repeat this process until there is just

enough tension to fully rewind the hose

6. The hose tension should only to tensioned

to the point where the hose stopper “just”

makes it back to the hose reel. If the hose

is returning to hard and fast to the hose reel

then the tension is too much and needs to

be adjusted accordingly. (Over tensioning

will not be covered by warranty)

CHANGING THE HOSE

1. Release all tension on the hose prior to

commencing. See section “ADJUSTING

THE SPRING TENSION”.

2. Note that all the hose needs to be pulled

out from the hose reel prior to commencing.

So the procedure in point 1 will have to be

done several times as the spring tension

will increase as the hose is extracted.

3. Once all the hose has been

pulled out move to point 3.

NOTE: DO NOT attempt to change the

hose while any tension on the spring

exists. Doing so can cause injury.

4. Using a at head screw driver, remove

the side cover marked “cover removal” by

prying it open where indicated. (this cover

is the same side as the inlet side of the

hose reel.

5. Move the internal drum until you expose

the hose connection window on the internal

drum. Use a small spanner / screw driver to

undo the hose clamp. Remove hose from

barded hose connection on the internal

drum and feed hose out of the hose reel.

6. Feed new hose through the roller guide

onto the barbed hose connection on the

internal drum. Retighten the hose clamp.

7. Replace the inlet side cover.

8. Re-tension the spring by following the

section “ADJUSTING THE SPRING

TENSION”.

9. As the spring gets more tension the hose

will automatically retract back into the hose

reel. Once hose has completely retracted

into the hose reel, adjust the tension on the

spring accordingly.

DO NOT over tension the spring. Doing

so will not allow the hose to be pulled out

entirely and may result in damage to the

hose reel and spring mechanism.

DO NOT over tension the spring. doing

so will not allow the hose to be pulled out

entirely and may result in damage to the

hose reel and spring mechanism

SPECIFICATIONS

Part

No.

Hose

Length

Hose

Material

Working

Pressure

Hose

I.D.

Hose

O.D.

Leader

Hose

Inlet

Size

58.3012 20 m Extreme Ultraex

Reinforced

Max. 300 p.s.i.

(20 BAR)

9.2 mm 15.2 mm 2 m 1/4” BSP

58.3023 30 m Extreme Ultraex

Reinforced

Max. 300 p.s.i.

(20 BAR)

9.2 mm 15.2 mm 2 m 1/4" BSP

58.3034 20 m Extreme Ultraex

Reinforced

Max. 150 p.s.i.

(10 BAR)

10.5 mm 16.5 mm 2 m 12mm

tap tting

58.3045 30 m Extreme Ultraex

Reinforced

Max. 150 p.s.i.

(10 BAR)

10.5 mm 16.5 mm 2 m 12mm

tap tting

MAINTENANCE

• Always keep the hose clean.

• If the hose becomes dirty, clean it with

a damp cloth while retracting.

• DO NOT twist the hose while in use.

• Mount the hose reel in a sheltered area to

assist and protect the performance of the

hose and hose reel.

• DO NOT allow the hose to contact any

corrosive chemicals or uids.

• Always retract the hose when not in use.

• The JamecPem PRO:X Hose Reel contains

a pre-tensioned spring inside the inner drum

assembly.

Do not attempt to open the inner drum

assembly.

WARRANTY

& CLAIM PROCEDURE

The JamecPem PRO:X Hose Reel is covered

against defects in material and workmanship.

In the instance of a warranty claim, the owner

will be entitled to a replacement unit or a

sufcient repair of the defective part/s and

or component/s to ensure normal operating

condition of the hose reel.

WARRANTY EXCLUSIONS

The hose, rubber o-rings and hose stopper

are deemed normal wear items and are not

covered under warranty.

The warranty does not extend to parts or

components affected or damaged by

accident, normal wear, misuse, neglect or

faulty installation.

To register a warranty claim contact:

Companion Brands

Phone: 1300 555 197

Fax: 1300 555 198

E-mail: enquires@companionbrands.com.au

NOTES

________________________________________________________________________________

SPECIFICATIONS

Part

No.

Hose

Length

Hose

Material

Working

Pressure

Hose

I.D.

Hose

O.D.

Leader

Hose

Inlet

Size

58.3012 20 m Extreme Ultraex

Reinforced

Max. 300 p.s.i.

(20 BAR)

9.2 mm 15.2 mm 2 m 1/4” BSP

58.3023 30 m Extreme Ultraex

Reinforced

Max. 300 p.s.i.

(20 BAR)

9.2 mm 15.2 mm 2 m 1/4" BSP

58.3034 20 m Extreme Ultraex

Reinforced

Max. 150 p.s.i.

(10 BAR)

10.5 mm 16.5 mm 2 m 12mm

tap tting

58.3045 30 m Extreme Ultraex

Reinforced

Max. 150 p.s.i.

(10 BAR)

10.5 mm 16.5 mm 2 m 12mm

tap tting

Distributed by

Companion Brands

Bundoora VIC 3083

www.companionbrands.com.au

jamecpem.com.au

JAM3702

This manual suits for next models

Table of contents

Other JAMEC PEM Tools manuals

JAMEC PEM

JAMEC PEM 11.0534 User manual