Jasco 39723 User manual

60-Watt
Wirelessly control, schedule, or dim your
bulb from anywhere
Smart LED Light Bulb
60W Smart Dimmable
LED Light Bulb
SKU#: 39723
Features
• Standard fit – Replace any standard A19 bulb with an E26 base to immediately turn
lamps, ceiling fans, recessed lights and more into smart devices.
• Full-range dimmability – The bulb adjusts brightness levels from 0-100 percent, which
reduces energy costs and improves bulb life.
• Long-life LEDs – Rated for up to 25,000 hours of use, long-lasting LEDs virtually elimi-
nates replacing bulbs for more than 22 years when used for three hours per day.
• Energy ecient – Using only 9W, the 60W-equivalent bulb oers an estimated energy
cost of $1.09 per year, which saves approximately $140 over its life.
•Range extender – The dimmer repeats your Z-Wave signal from your hub or other
Z-Wave device to extend your range by up to 150ft. Extended signal range increases your
home automation coverage to enhance your control.
See life in a new light with the Jasco Enbrighten
Z-Wave Smart LED Bulb. When paired with a
compatible hub, the smart bulb supports
ON/OFF/dim commands and programmed
settings. Wirelessly operate lamps, sconces, ceiling
lights and other fixtures that use standard A19
bulbs for eortless management of your home.
39723 PRODUCT OVERVIEW

OMNI-DIRECTIONAL LIGHT
The 750-lumen LEDs are optimally configured to emit soft
white (2,700K) light evenly around the room.
1
PRODUCT OVERVIEW
STANDARD FIT
Wirelessly operate lamps, sconces, ceiling lights and other
fixtures that use standard A19 bulbs for eortless
management of your home. Compatible with any standard
A19 bulb with an E26 base to immediately turn lamps, ceiling
fans, recessed lights and more into smart devices.
FULL-RANGE DIMMABILITY
The Smart Bulb adjusts brightness levels from 0-100 percent,
which reduces energy costs and increases life.
UNIVERSAL COMPATIBILITY
Z-Wave Plus and all previous Z-Wave generations work
together to allow continued expansion of your
home-automation network. The dimmer repeats your Z-Wave
signal from your hub or other Z-Wave device to extend your
range by up to 150ft. Extended signal range increases your
home automation coverage to enhance your control.
39723

2
PRODUCT SPECIFICATIONS39723
Bulb: A19
Signal Frequency: 908.4/916
Range:Up to 150 feet from controller or closest Z-Wave device
Operating Temperature: 32-104° F (0-40° C)
Warranty:2-year limited product warranty
For indoor use only.
Enbrighten®Z-Wave
Smart LED Bulb
Design Features
· Full-Range Dimmability
Adjust brightness levels
from 0-100% (1% increments)
· Omni-directional lighting
Enbrighten LEDs are
optimally to
provide a bright, evenly
distributed glow
· 60W Bulb Equivalent
Lightoutput is equivalent to a
standard 60W bulbwhile
onlyusing 9W of electricity
· Save $140 over life of bulb**
Enbrighten LEDs can reduce
energy usage by up to 85%
· OTA (Over-the-Air) Updateable
Utilizes the Z-Wave Firmware
Update Meta Data command
classfor standardized wireless
updates
· Visit http://www.ezzwave.com/
hubs/for hub compatibility
· Trilingual Instruction manual –
(English, French, Spanish)
Z-Wave Plus Features
·Works with Z-Wave Classic
and Z-Wave Plus Products
·50% more wireless range
·250% faster processor
·400% more memory
·Supports wireless upgrades
to future-proof your home
** Time and cost estimates as compared to a
60W incandescent bulb over the life of the
product (25,000 hrs) at .11¢/kWh. Results
will vary based on rates and use.

3
PRODUCT SPECIFICATIONS39723
subject to change without notice
Distributed by Jasco Products Company LLC
10 E. Memorial Rd., Oklahoma City, OK
©Jasco 2018
Adding your device to a Z-Wave network
Once the hub is ready to add your LED smart bulb, turn on
power to the socket. The bulb will be automatically
added into your network within 30 seconds and the bulb
.
To remove and reset the device
Once the controller is ready to remove your LED smart bulb, turn
successful removal from the network.
To return to factory defaults
Cycle the wall switch ON/OFF 4 times within 4 seconds
(completing one successive OFF and ON action counts as
succesful reset.
Omni-Direction Light
to provide a bright, evenly distributed glow
60W Bulb Equivalent
Light output is equivalent to a standard 60W
bulb while only using 9W of electricity.
Brightness
Estimated Yearly Energy Cost
Based on 3 hrs/day, 11¢/kWh
Cost depends on rates and use
Life
Based on 3 hrs/day
Light Appearance
Warm Cool
2700 K
Energy Used
750 lumens
$1.09
22.8 years
9 watts
Lighting Facts
Per Bulb

4
39723 QUICKSTART GUIDE
IMPORTANT!
Please note that it is extremely important to follow the below practice or to use ONLY
your preferred wireless remote control device to turn the smart bulb ON or OFF. Without
electrical power to the light bulb, the smart bulb cannot be turned ON remotely nor function
as a signal repeater to maintain proper Z-Wave network.
To avoid family members from accidently turning OFF the power to the smart bulb, install
the separate installation sheet.
®

QUICKSTART GUIDE
5
39723
¡IMPORTANTE!
Tenga presente que es sumamente importante observar la práctica descrita arriba o usar
ÚNICAMENTE su dispositivo de control remoto inalámbrico preferido para encender y
apagar la bombilla inteligente. Sin alimentación eléctrica, la bombilla inteligente no se
puede encender de manera remota ni funcionar como repetidor de la señal para mantener
adecuadamente la red Z-Wave.
Para evitar que los miembros de su familia desconecten la alimentación a la bombilla
inteligente, instale la tapa transparente opcional sobre el interruptor de pared (incluida con
el producto). Consulte la hoja de instalación que viene aparte.
IMPORTANT!
Veuillez noter qu’il est extrêmement important de respecter la pratique susmentionnée ou
intelligente. Sans alimentation électrique vers l’ampoule, l’ampoule intelligente ne peut être
allumée à distance ni fonctionner comme répétiteur de signaux servant à maintenir le réseau
Z-Wave approprié.
Pour éviter que les membres de la famille coupent accidentellement l’alimentation de l’ampoule
intelligente, installez le couvercle transparent en option qui se place sur votre interrupteur mural
(compris avec le produit). Veuillez vous reporter à la feuille d’instructions d’installation fournie.