JETWAY JLI1BV-0L Series User manual

Quick Installation Guide
NO. G03-JC903QIG01-F
MB Model: JLI1BV-0L Series
Rev: 1.0
Release Date: 2022-11-03
Notice:
The photos in this file are for illustration purpose only. The model may not be the latest version. Please
refer to the product you purchased for actual specification.

I. To Dissemble the Chassis
1. Put the system upon a stable platform with this side up, as the photo shows.
2. Locate the screws at the spots marked on the cover and unscrew them one by one.
3. Lift the cover up to open the chassis.

4. The internal structural view of the system for further intallation.
II. To Install SO-DIMM to the Board
1. Locate the SO-DIMM slot on the board.
2. Insert the gold-finger side of the compatible
SO-DIMM into the slot at a 30 degree.
3. Press down to secure the SO-DIMM to the slot.
The eject tabs will lock automatically if installing
direction is correct.

III. To Install M.2 E-Key (2230) PCIe Wi-Fi Card
1. Sort out the USB cable to make room and
locate the M.2 E-Key (2230) slot on the board.
Prepare compatible M.2 E-Key (2230) card.
2. Remove the marked screw and screw bolt, and
use screw bolt to lock compatible card to the slot
in later installation.
3. Insert the gold-finger side of the compatible
card into the slot and press down. See to it that
the golden-finger side should be fully plugged
into the slot.
4. Secure the card to the board by tightening up
the screw bolt to the marked spot.
5. Locate the reserved antenna holes on the rear
panel. Remove the dust-proof plugs on the
marked spots from the panel to install the
antenna.
6. Remove the two marked screws from the
HDMI cable and remove the HDMI connector
from the panel.

7-1. The washer①&the hexagonal screw nut②.
7. Push this antenna screw head into antenna
hole of the panel from the backside of the panel.
7-2. Push the washer① through the antenna
head.
8. And then lock the antenna screw head to the
front side of the panel with the hexagonal screw
nut ② and tighten it up.
9. Press the metal hat on the end of the antenna
string to corresponding antenna slot on the card
as showed.
10.Repeat step 7 to 9, to finish installation of the
other antenna.
11.Connect the external Wi-Fi receiver antenna
to the antenna screw head on the panel, and
reinstall the HDMI cable you removed in step 6.

IV. To Install M.2 M-Key (2242/2280) PCIe/SATA Card
1. Sort out the USB cable to make room and
locate the M.2 SATA slot on the board. System
supports two types of M.2 M-Key card in
different lengths (2242/2280). Prepare
compatible M.2 M-Key (2242/2280) card
2. To install compatible type-2242 card, please
remove the screw in the marked spot at first.
3. Insert compatible M.2 M-Key (type-2242) card
into the slot. See to it that the golden-finger side
should be fully plugged into the slot.
4. Tighten up the screw removed before to the
marked spot to secure the card.
*Note: If you wish to install type-2280 card, please remove the screw and the screw blot on location MH2
and reinstall the screw post underneath on the location MH4 before installing type-2280 card to the slot.
The other steps are the same as M.2 M-key type-2242 card installation.
2242
2280

V. To Install M.2 B-Key (3042/3052) Card
1. Locate the M.2 B-Key PCIe (3042/3052) slot on
the board. Prepare compatible M.2 B-Key
(3042/3052) card.
2. Remove the marked screw and use it to lock
compatible card to the slot in later installation.
3. Insert the gold-finger side of the compatible
M.2 B-Key (type-3042) card into the slot and
press down. See to it that the golden-finger side
should be fully plugged into the slot.
4. Secure the card to the board by tightening up
the screw to the marked spot.
*Note: If you wish to install M.2 B-key type-3052 card, please remove the installed M.2 B-key type-
3042 card and remove the screw at location MH3 before installing type-3052 card to the slot. The
other steps are the same as M.2 B-key type-3042 card installation.
3042
3052

VI. To Install 2.5” Hard Disk to HDD Tray
1. Locate the HDD racks on the chassis.
2. Push the 2.5’’ HDD into the room between the
racks until the screw holes of the racks
matched those in the HDD and make sure the
direction is as same as picture showed.
3. Lock the 2.5’’HDD to the racks by tightening
up the marked four screws.
4. Connect SATA power cable & one end of
compatible SATA cable to corresponding
connectors from the hard disk.
5. Sort and place the SATA cable and SATA power cable beside the case as showed above.

Notice: Make sure that: 1.the racks are installed to its original place; 2. HDD SATA & power connectors
face towards the direction of the chassis with enough room to facilitate cable connection.
Notice: When all necessary installations are finished, please make sure that all cables unplugged before
installations are connected to their original locations before restoring the cover to the chassis and
screws locked to its original locations (Refer to Part I). See to it that the cables inside are not blocked or
pressed.
VII. To Install wall mount racks to the system
1. Install wall mount rack to the system by
tightening two screws in the marked
positions.
2. Then lock the other two screws on the
other side in the same way.
3. Wall mount the system by tightening 4 screws in the marked positions (within small-sized or
large-sized frame) on both sides of the wall racks.
Wall Mount Screw Holes (Large-sized)
Wall Mount Screw Holes
(Small-sized)