JETWAY MI02 Series User manual

MI02 Series
User’s Manual
No. G03-MI02-F
Rev: 2.0
Release date: October 26, 2021
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii
ENVIRONMENTAL SAFETY INSTRUCTION................................................................................... iii
ENVIRONMENTAL PROTECTION ANNOUCEMENT.................................................................... iii
USER’S NOTICE.................................................................................................................................... iv
MANUAL REVISION INFORMATION................................................................................................ iv
ITEM CHECKLIST..................................................................................................................................iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 GENERAL SPECIFICATIONS............................................................................................. 1
1-2 LAYOUT DIAGRAMS............................................................................................................ 2
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................................ 8
2-2 CONNECTORS AND HEADERS........................................................................................ 10
2-2-1 REAR I/O BACK PANEL CONNECTORS......................................................... 10
2-2-2 MOTHERBOARD INTERNAL CONNECTORS................................................. 11
2-2-3 HEADER PIN DEFINITION....................................................................................14
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP............................................................................................................. 18
3-2 BIOS MENU SCREEN...........................................................................................................19
3-3 FUNCTION KEYS...................................................................................................................19
3-4 GETTING HELP......................................................................................................................20
3-5 MENU BARS........................................................................................................................... 20
3-6 MAIN MENU............................................................................................................................ 20
3-7 ADVANCED MENU................................................................................................................21
3-8 CHIPSET MENU..................................................................................................................... 32
3-9 BOOT MENU...........................................................................................................................34
3-10 SECURITY MENU.................................................................................................................. 36
3-11 SAVE & EXIT MENU..............................................................................................................37
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 Second Edition October 26,2021
Item Checklist
Motherboard
Cable(s)
I/O Back panel shield

1
Chapter 1
Introduction of the Motherboard
1-1 General Specifications
Spec
Description
Design
Slim Mini-ITX form factor; PCB size: 17 x17cm
Chipset
MI02-10/12 Series: Intel Q470E Chipset
MI02-20/22 Series: Intel W480E Chipset
MI02-30/32 Series: Intel H470 Chipset
MI02-40/42 Series: Intel H420E Chipset
CPU Socket
Intel LGA 1200 Socket supports 10th/11th Core
i9/i7/i5/i3/Pentium/Celeron processors (Max. 65W TDP)
*Note:for detailed CPU support information please visit our website
Memory Slots
2*DDR4 SO-DIMM slot support 2* DDR4 SDRAM
Maximum frequency:2933/2666/2400MHz(depends on CPU support)
Maximum capacity: up to 64GB
Support dual channel function
*Note: MI02-20/22 series supports DDR4 ECC SDRAM
Expansion
Slots
PCIE1: 1 * PCI-Express x16 slot(Suggest the PCIe card less than 25W
Power consumption)
M2E:1* M.2 E-key type-2230 (PCIex1/USB2.0) slot
M2B: 1* M.2 B-key type-3042/3052 (USB3.0/ PCIex1) slot co-function
with SIM card slot
SIMCARD1: 1* Nano SIM card slot (Backside,co-function with M2B)
*Note:For M2E/M2B slot maximum current limit is 2A while using 3.3V.
Storage
SATA1:1*SATAIII 6Gb/s port (*Optional)
M2M:1* M.2 M-key slot, type-2280 (SATA/*PCIex4) slot supports
NVMe
*Note:M2M slot maximum current limit is 2A while using 3.3V;PCIex4
support depends on chipset models(H420E not support)
LAN Chips
MI02-10/12 & MI02-20/22 Series: 1* Intel i219LM GbE & 1* Intel
i225LM 2.5GbE
MI02-30/32 & MI02-40/42 Series: 1* Intel i219VGbE & 1* Intel
i225LM 2.5GbE
Audio Chip
Realtek HD Audio Codec integrated
Audio driver and utility included
BIOS
AMI 256M Bit AMI Flash ROM
Multi I/O
Rear Panel I/O:
MI02-10/12 & MI02-20/22& MI02-30/32: 4* USB 3.2 (Gen.2) 10Gbps
port
MI02-40/42: 4* USB 3.2 (Gen.1) 5Gbps port
1* 1GbE RJ-45 LAN port
1* 2.5GbE RJ-45 LAN port
1* Display port
2* HDMI 1.4 port
1* Line-Out port
1* MIC port
1* 12V~28V wide voltage DC-IN power jack
Internal I/O Connectors & Headers:

2
1 *4-pin ATX-Type 12V power connector
1* CPUFAN connector & 1* SYSFAN connector
1* SATA power-out connector (*Optional)
1* EDP connector (Backside)
1* Front panel header
MI02-10/12 & MI02-20/22& MI02-30/32:1* 19-Pin USB 3.2 (Gen.1)
header for 2* USB 3.2 (Gen.1) 5Gbps port
MI02-10/12 & MI02-20/22& MI02-30/32: 2* 9-Pin USB 2.0 header for
4* USB 2.0 expansion ports
MI02-40/42: 1* 9-Pin USB 2.0 header for 2* USB 2.0 expansion
ports
4* COM port header (*COM1/COM2:RS232/422/485)
1* 8-bit GPIO header
1* Front panel audio header
1* SMBUS header
1* LVDS header
1* LVDS inverter
TPM 2.0 Function
Optional for MI02-12/22/32/42 Series
Model specification main differences ：
Differences
MI02-10/12
MI02-20/22
MI02-30/32
MI02-40/42
Chipset
Q470E
W480E
H470
H420E
LAN Chip
I219LM
+I225LM
I219LM
+I225LM
I219V
+I225LM
I219V
+I225LM
Rear IO USB 3.2
4*USB3.2(Gen2)
4*USB3.2(Gen2)
4*USB3.2(Gen2)
4*USB3.2(Gen1)
Intenal USB 3.1
(Gen1) Header
Yes
Yes
Yes
N/A
Intenal USB 2.0
Header
2*9-pin USB2.0
2*9-pin USB2.0
2*9-pin USB2.0
1*9-pin USB2.0
SATAIII+SATA
Power out
Yes
Yes
Yes
N/A
Multi-Display
Support
Triple Displays
Triple Displays
Triple Displays
Dual Displays
M2E Slot
Support CNVi
Support CNVi
Support CNVi
CNVi not supported
M2M Slot
SATA/PCIex4
SATA/PCIex4
SATA/PCIex4
SATA
1-2 Layout Diagrams
Rear IO Diagram
*Note: MI02-10/12 & MI02-20/22 & MI02-30/32 supports 4*USB 3.2(Gen.2) ports
while MI02-40/42 supports 4*USB 3.2(Gen.1) ports
*USB 3.2 Ports
LAN1: 1GbE RJ-45
LAN Port
LAN2: 2.5GbE
RJ-45 LAN Port
Display Port
HDMI Ports
Line-Out
MIC
12V~28V
DC-IN
Power Jack

3
Motherboard Internal Diagram-Front
For MI02-10/12 & MI02-20/22 & MI02-30/32:
*Rear IO
Connector
(Refer to Page-2)
LGA 1200
CPU Socket
SATAIII Port
M.2 M-Key Slot
(M2M)
M.2 E-Key Slot
(M2E)
Front Panel
Header
PCI Express x16 Slot
(PCIE1)
M.2 B-key Slot
(*M2B)
SATA Power-out
Connector
SYSFAN1
Connector
Serial Port Headers
(COM1/2/3/4)
GPIO Port
Header
2*DDR4
SODIMM Slots
LVDS Header
INVERTER
SMBUS
Header
USB 2.0 Headers
USB 3.2 (Gen.1)
Header
CPUFAN
Connector
Front Panel
Audio Header
ATX 12V
Power Connector
（DCIN2）

4
For MI02-40/42:
*Rear IO
Connector
(Refer to Page-2)
LGA 1200
CPU Socket
M.2 M-Key Slot
(M2M)
M.2 E-Key Slot
(M2E)
Front Panel
Header
PCI Express x16 Slot
(PCIE1)
M.2 B-key Slot
(*M2B)
SYSFAN1
Connector
Serial Port Headers
(COM1/2/3/4)
GPIO Port
Header
2*DDR4
SODIMM Slots
LVDS Header
INVERTER
SMBUS
Header
USB 2.0 Header
CPUFAN
Connector
Front Panel
Audio Header
ATX 12V
Power Connector
（DCIN2）

5
Motherboard Internal Diagram-Back
*Note: SIM card slot only functions when compatible Nano SIM card installed &
compatible 3G/4G/5G card installed in M2B slot.
Intel
Chipset
EDP
Connector
*Nano SIM
Card Holder
(SIMCARD1)

6
Motherboard Jumper Position:
*Note: The diagrams in the manual are mostly taken from MI02-10 series unless
otherwise stated.
Jumper
Jumper
Name
Description
Pitch
JAT_ATX
ATX/AT Mode Select
3-pin Block
2.0mm
JBAT
Clear CMOS RAM Settings
3-pin Block
2.0mm
JP2
LVDS INVERTER Backlight VCC Select
3-pin Block
2.0mm
JP3
LVDS PANEL VCC Select
3-pin Block
2.0mm
COPEN
Case Open Message Display Detect
2-pin Block
2.0mm
JP1
ME Features Select
2-pin Block
2.0mm
JAT_ATX
JBAT
JP3
COPEN
JP1
JP2

7
Connectors
Connector
Name
*USB1/USB2
MI02-10/20/30 & MI02-12/22/32: USB 3.2 (Gen.2) Port X4
MI02-40 & MI02-42:USB 3.2 (Gen.1) Port X4
LAN1
1GbE RJ-45 LAN Port
LAN2
2.5GbE RJ-45 LAN Port
DP3
Display Port
HDMIX2
HDMI 1.4 Port X2
HOUT1
Audio Line Out Port
HMIC1
Audio MIC Port
DCIN2
12V~28V DC-IN Power Jack
DCIN1
ATX type 12V Power Connector
*SATA1
SATAIII Port Connector
*PWROUT
SATA Power Out Connector
SYSFAN1
System FAN Connector
CPUFAN
CPU FAN Connector
EDP1
EDP Connector
*Note ： SATA1 & PWROUT are optional for MI02-10/20/30 &MI02-12/22/32 series only.
Headers
Header
Name
Description
Pitch
JW_FP
(Front Panel
Header)
PWR LED/ HD LED/ Power
Button /Reset
9-pin Block
2.54mm
*FP_USB1
USB 3.2 (Gen.1) Port Header
19-pin Block
2.0mm
FP_USB2
USB 2.0 Port Header
9-pin Block
2.0mm
*FP_USB3
USB 2.0 Port Header
9-pin Block
2.0mm
COM1/2
RS232/422/485 Serial Port
Header
9-pin Block
2.0mm
COM3/4
RS232 Serial Port Header
9-pin Block
2.0mm
GPIO
GPIO Header
10-pin Block
2.0mm
SMBUS1
SMBUS Header
5-pin Block
2.0mm
FP_AUDIO
Front Panel Audio Header
9-pin Block
2.0mm
INVERTER1
LVDS Inverter
6-pin Block
2.0mm
LVDS1
LVDS Header
30-pin Block
1.25mm
*Note:FP_USB1 & FP_USB3 are only optional for MI02-10/20/30 &MI02-12/22/32 series.

8
Chapter 2
Hardware Installation
2-1 Jumper Setting
JAT_ATX (3-pin): AT Mode /ATX Mode Select
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
JBAT (3-pin): Clear CMOS RAM Settings
2-3 Closed: Clear CMOS.
1-2 Open: Normal；
1
3
1
3
JBAT → Clear CMOS Settings
JBAT
JAT_ATX

9
JP2(3-pin): LVDS Inverter Backlight VCC Select
1
3
1
3
JP2 → LVDS Inverter VCC Select
1
-2 Closed: VCC=+5V (Default);
;
2-3 Closed: VCC=+12V.
JP3(3-pin): LVDS Panel Power VCC Select
COPEN (2-pin): Case Open Message Display Function
Pin1
COPEN → Case Open Detection
CASE OPEN
GND
Pin 1-2 Short:When Case open function pin short to GND, the Case open function
was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’
function. In this case if your case is removed, next time when you restart your
computer, a message will be displayed on screen to inform you of this.
JP3
JP2
COPEN

10
JP1(2-pin): ME Features Select
Pin1
JP1 → ME Features Select
Pin1
1-2 Closed: Disable ME Features.
1-2 Open: Enable ME Features(Default);
2-2 Connectors and Headers
2-2-1 Rear I/O Back Panel Connectors
*Refer to Page-2 Rear IO Diagram
Icon
Name
Function
USB 3.2 Port
To connect USB keyboard, mouse or other
devices compatible with USB 3.2 specification.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection. (LAN1 Intel®i219-LM/ i219-V
PHY LAN port supports up to 1.0 Gbps transfer
rate; LAN2 from Intel®i225-LM supports up to
2.5Gbps transfer rate;).
Display Port
For user to the system to corresponding display
device with compatible DP cable.
HDMI 1.4 Port
To connect display device that support HDMI
specification.
Line-out
For user to connect external speaker, earphones,
etc to transfer system audio output.
MIC
User can connect microphone device to this port.
JP1

11
12V~28V DC-in
Power Jack
For user to connect compatible power adapter to
provide power supply for the system.
*Note:Maximum current limit for rear panel USB1/USB2 port is 1.5A while using 5V
working voltage.
2-2-2 Motherboard Internal Connectors
(1) DCIN1 (4-pin block): ATX Type 12V Power Connector
This is a new defined 4-pin connector that usually comes with ATX Power Supply that
supports extra 12V voltage to maintain system power consumption. Without this
connector might cause system unstable because the power supply can not provide
sufficient current for system.
Pin No.
Definition
1
GND
2
GND
3
+12V
4
+12V
Pin1
4
2
3
(2) *SATA1(7-pin): SATAIII Port connector
SATA1 is only optional for MI02-10/20/30 &MI02-12/22/32 series.
This is a high-speed SATAIII port that supports 6GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
SATA1

12
(3) *PWROUT (4-pin): SATA HDD Power-Out Connector
PWROUT is only optional for MI02-10/20/30 &MI02-12/22/32 sereis.
Pin1
+12V
GND
+5V
GND
*Note:Maximum current limit for USB ports from POWOUT is 2A while using 5V or
12V working voltage.
Warning: Make sure that Pin-1 of compatible SATA Power out connector is inserted into
corresponding Pin-1 of PWROUT connector to avoid possible damage to the board and hard disk
driver!
(4) SYSFAN1 (4-pin): System FAN Connector
Fan Speed
GND
Pin1
+12V Fan Power
Control
*Note:Maximum current limit is 1.5A while using 12V working voltage.
(5) CPUFAN (4-pin): CPU FAN Connector
+12V Fan Power
GND
Fan Speed
Control
Pin1
*Note:Maximum current limit is 1.5A while using 12V working voltage.
SYSFAN1
PWROUT
CPUFAN

13
(6) EDP1(40-pin): EDP Connector
Pin No.
Pin Define
Pin No.
Pin Define
Pin 1
NC
Pin 21
LCD_VCC
Pin 2
GND
Pin 22
NC
Pin 3
EDP_LANE3N
Pin 23
GND
Pin 4
EDP_ LANE3P
Pin 24
GND
Pin 5
GND
Pin 25
GND
Pin 6
EDP_LANE2N
Pin 26
GND
Pin 7
EDP_ LANE2P
Pin 27
EDP_HPD
Pin 8
GND
Pin 28
GND
Pin 9
EDP_LANE1N
Pin 29
GND
Pin 10
EDP_LANE1P
Pin 30
GND
Pin 11
GND
Pin 31
GND
Pin 12
EDP_LANE0N
Pin 32
EDP_BKLT_EN
Pin 13
EDP_LANE0P
Pin 33
EDP _BKLT_CTL
Pin 14
GND
Pin 34
NC
Pin 15
EDP_AUXP
Pin 35
NC
Pin 16
EDP_AUXN
Pin 36
LCD_BKLT_PWR VCC
Pin 17
GND
Pin 37
LCD_BKLT_PWR VCC
Pin 18
LCD_VCC
Pin 38
LCD_BKLT_PWR VCC
Pin 19
LCD_VCC
Pin 39
LCD_BKLT_PWR VCC
Pin 20
LCD_VCC
Pin 40
NC
*Note: The board co-lays LVDS header and EDP connector; i.e. only one can function at a
time. User can go to BIOS settings to select one of them as the display output port.
EDP1

14
2-2-3 Header Pin Definition
(1) JW_FP (9-pin): Front Panel Header
*Note: Maximum current limit is 1A while using 5V working voltage.
(2) *FP_USB1(19-pin): USB 3.1(Gen.1) Port Header
FP_USB1 is only optional for MI02-10/20/30 &MI02-12/22/32 sereis.
D2-
GND2
Pin1
NC
GND0
19
D-
GND1
SSRX1-
VBUS_5V
SSTX2-
SSTX2+
GND3
VBUS_5V
11
10
SSRX2+
SSRX2-
SSRX1+
SSTX1-
SSTX1+
D2+
D+
*Note: Maximum current limit is 1.5A
in total while using 5V working voltage.
(3) FP_USB2/*FP_USB3(9-pin): USB 2.0 Port Headers
FP_USB3 is only optional for MI02-10/20/30 &MI02-12/22/32 series.
-DATA
NC
GND
+DATA
GND
VCC5V
+DATA
Pi n1
VCC5V
-DATA
2
*Note: Maximum current limit is 1.5A
in total while using 5V working voltage.
JW_FP
FP_USB2
*FP_USB3
(Optional)
*FP_USB1
(Optional)
*FP_USB1
(Optional)

15
(4) COM1/2/3/4 (9-pin): Serial Port Header
COM1 &COM2 ： RS232/422/485 Serial Port;
COM3&COM4 ： RS232 Serial Port Header.
6
Pin 1
COM3
COM4
*COM2
*COM1
Pin NO.
RS232
*RS422
(optional)
*RS485
(optional)
Pin 1
DCD
TX-
DATA-
Pin 2
RXD
TX+
DATA+
Pin 3
TXD
RX+
NC
Pin 4
DTR
RX-
NC
Pin 5
GND
GND
GND
Pin 6
DSR
NC
NC
Pin 7
RTS
NC
NC
Pin 8
CTS
NC
NC
Pin 9
RI
NC
NC
*Notice: COM1/2 header can function as RS232/422/485 port header. In normal
settings COM1/2 functions as RS232 header. With compatible COM cable COM1/2
can function as RS422 or RS 485 header. User also needs to go to BIOS to set
‘Transmission Mode Select’ for COM1 or COM2 at first, before using specialized
cable to connect different pins of this port.
(5) GPIO (10-pin): GPIO Port Header
VCC
Pin1
2
GPIO77
GPIO75
GPIO73
GND
GPIO76
GPIO74
GPIO72
GPIO66
GPIO71
*Note: Maximum current limit is 1A while using 5V working voltage.
GPIO

16
(6) SMBUS1 (5-Pin): SMBUS Header
Pin1
GND
SMBUS_DATA
SMBUS_CLK
VCC3
SMBUS_ALERT-
SMBUS_DATA
*Note: Maximum current limit is 500mA while using 3.3V working voltage.
(7) FP_AUDIO (9-pin): Line-Out, MIC-In Header
This header connects to Front Panel Line-out, MIC-In connector with cable.
GND
MIC_JD
SENSE
LINE_OUT_R
Pin
1
MIC2_L
AUDIO_JD
2
MIC2_R
LINE OUT_L
LINE_OUT_JD
(8) INVERTER1(6-pin): LVDS Inverter
Pin No.
Definition
1
BKLT_PWR1
2
BKLT_PWR2
3
BKLT_EN
4
BKLT_PWM
5
BKLT_GND1
6
BKLT_GND2
Pin1
*Note: Maximum current limit is 2A
in total while using 12V working voltage.
SMBUS1
FP_AUDIO
INVERTER1