JETWAY MI24 Series User manual

MI24 Series
User’s Manual
NO. G03-MI24-F
Revision: 1.0
Release date: November 23, 2023
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

ii
ENVIRONMENTAL SAFETY INSTRUCTION............................................................................. iii
USER’S NOTICE...............................................................................................................................iv
MANUAL REVISION INFORMATION...........................................................................................iv
ITEM CHECKLIST............................................................................................................................ iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD.........................................................................................1
1-2 SPECIFICATION.................................................................................................................... 2
1-3 LAYOUT DIAGRAM...............................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTINGS..............................................................................................................8
2-2 CONNECTORS, HEADERS AND WAFERS.....................................................................12
2-2-1 REAR I/O PANEL CONNECTORS...................................................................... 12
2-2-2 MOTHERBOARD INTERNAL CONNECTORS................................................. 15
2-2-3 PIN DEFINITIONS FOR HEADERS & WAFERS.............................................. 17
2-3 MAXIMUM VOLTAGE & CURRENT LIMIT....................................................................... 23
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP................................................................................................................ 24
3-2 BIOS MENU SCREEN...........................................................................................................25
3-3 FUNCTION KEYS...................................................................................................................26
3-4 GETTING HELP......................................................................................................................26
3-5 MENU BARS........................................................................................................................... 27
3-6 MAIN MENU............................................................................................................................ 27
3-7 ADVANCED MENU................................................................................................................28
3-8 CHIPSET MENU..................................................................................................................... 41
3-9 SECURITY MENU.................................................................................................................. 44
3-10 BOOT MENU...........................................................................................................................47
3-11 SAVE & EXIT MENU..............................................................................................................48
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The temperature comes from the
request of the chassis and thermal solution)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition November 23, 2023
Item Checklist
Motherboard
I/O shield
Cables

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
Intel®13th Raptor Lake-P i5-1335UE/i5-1355U SoC Processor (15W TDPs)
2* DDR5 4800MHz SO-DIMM up to 64GB
Integrated with 2* Intel®2.5GbE LAN chips
2* HDMI, 1* LVDS (or 1-Lane eDP)
2* USB3.2 (Gen.2), 2* USB3.2 (Gen.2) Type-C support DP ALT mode and PD
5V/3A, 7* USB2.0
Support 4* RS232 & 2* RS232/422/485
Onboard 1* M.2 E-key type-2230 slot for WiFi support CNVi, 1* M.2 B-key
type-3042/3052 slot for 4G/5G module, 1* SIM card holder, 1 * M.2 M-Key
type-2242/2280 slot (PCIe Gen.4 x4 Interface) support NVMe ;1* PCIe Gen.3 x1
slot
Support 1* SATAIII (6Gb/s) & 1* M.2 M-key type-2242 slot (SATA interface)
Support 12V~24V DC-in
Onboard TPM2.0 (option)
Support JetBIOS back up tool
Support CPU Smart FAN function
Supports ACPI S3 Function
Support Watchdog Timer Technology

2
1-2 Specification
Spec
Description
Design
Slim ITX form factor; 10-layers; PCB size: 170x170mm
Embedded CPU
Intel®13th Raptor Lake-P i5-1335UE /i5-1335USoC Processor
*For detailed CPU support information please visit our website
Memory Slots
2*DDR5 SO-DIMM slots support 2* 4800MHz DDR5 SO-DIMM up to 64GB
Support dual channel function
*Note:Memory frequency range also depends on CPU support
Storage
SATA1: 1* SATAIII 6G/s connector
M2M1: 1* M.2 M-key 2242 (SATA interface) slot
Expansion Slots
PCIE1: 1*PCIe Gen.3 x1 slot
M2E1:1* M.2 E-key 2230 (USB2.0/PCIex1 interface) slot supports CNVi for
WiFi
M2B1:1*M.2 B-key 3042/3052 (USB3.1/USB2.0/PCIex1 interface) slot for
4G/5G Module
SIMCARDB1:1* Nano-SIM card slot; co-function with M2B1 slot
M2M2: 1* M.2 M-key 2242/2280 (PCIe Gen.4 x4 interface) slot supports
NVMe
Graphics
Intel®Iris®Xe Graphics, shared memory for:
2* HDMI 2.0b
2* DP 1.4a from 2* USB3.2 (Gen.2) Type-C
1* LVDS/eDP
* Note: MI24 series support Quad Displays
LAN Chips
Integrated with 1* Intel i225-LM & 1* Intel i225-V dual 2.5GbE PCIe LAN
chips
Support 10/100/1000/2500Mbps Ethernet data transfer rate
*Note: 2500Mbps high-speed transmission rate is only supported over CAT 5e
UTP cable.
BIOS
AMI 256Mb Flash ROM
Rear I/O
1* 4-Pin 12V~24V Mini-DIN DC-in power jack
4* USB 2.0 ports
2* USB 3.2 (Gen.2) ports
2* HDMI ports
2* USB 3.2 (Gen.2) Type-C support DP ALT mode and PD 5V/3A
2* 2.5GbE RJ-45 LAN ports

3
1* Audio jack (Line-out/MIC combo)
Internal I/O
1* 12V~24V internal ATX-type power connector (DCIN2)
1* SATA HDD power-out connector
1* CPUFAN1 connector
1* Front panel hearer
1* Front panel audio header
1* 3W 8ΩSpeaker wafer
1* LAN Activity LED header (JLANLED1)
1* 9-Pin USB 2.0 header for 2* USB 2.0 expansion ports
1* 4-Pin USB 2.0 header for 1* USB 2.0 expansion port
1* PS/2 Keyboard & Mouse header
1* SMBUS header
1* 8-bit GPIO header
2* Serial headers support RS232/422/485 (COM1/2)
4* Serial headers support RS232(COM3/4/5/6)
1* LVDS header (or 1-Lane eDP)
1* Inverter wafer
TPM 2.0
Optional for MI24-133E2 & MI24-13352 Series
1-3 Layout Diagram
Rear IO Diagram
12V~24V DC-in
Power Jack
USB 2.0 Ports
USB 3.2 (Gen.2)
Ports
HDMI Ports
USB 3.2 (Gen.2)
Type-C Ports
Support ALT
mode
2.5GbE
RJ-45 LAN Ports
(LAN1: I225V)
Line-Out/MIC Combo
Audio Jack
2.5GbE
RJ-45 LAN Ports
(LAN2: I225-LM)

4
Motherboard Internal Diagram
*Note: SIMCARDB1 slot only work when compatible SIM card installed & 4G/5G LAN card installed in M2B1 M.2 B-key slot.
*Rear IO
Connector
(Refer to Page-3)
Internal ATX-Type
Power Connector
(DCIN2)
CPUFAN1
SPEAK_CON1
PCIE1: PCIe Gen.3x1 Slot
DDR5
SODIMM Slots
INVERTER1
Front Panel
Audio Header
M.2 E-Key Slot
(M2E1)
M.2 B-Key Slot
(*M2B1)
SIM Card Slot
(*SIMCARD1)
M.2 M-Key Slot
(M2M2)
M.2 M-Key Slot
(M2M1)
LVDS1
SATAIII Port
(SATA1)
SATAPWR1
Front Panel Header
GPIO Header
PS2KBMS1
USB2.0 Headers
Serial Port Headers
(COM1/2/3/4/5/6)
JLANLED1
SMBUS1

5
Motherboard Jumper Position
JPCOM1
JPCOM2
JATX_AT1
J80PORT1
JME1
JCLR_CMOS
JP1
JP2
JCASE1

6
Jumpers:
Jumper
Function
Description
Pitch
JCLR_CMOS
Clear CMOS RAM Settings
2-pin Block
2.0mm
JPCOM1
COM1 Header Pin9 Function Select
4-pin Block
2.0mm
JPCOM2
COM2 Header Pin9 Function Select
4-pin Block
2.0mm
JATX_AT1
ATX Mode / AT Mode Select
3-pin Block
2.0mm
JCASE1
Case Open Display Select
2-pin Block
2.0mm
J80PORT1
GPIO/80 Port Function Select
2-pin Block
2.0mm
JME1
ME_Features Select
2-pin Block
2.0mm
JP1
LVDS INVERTER Backlight Power Select
4-pin Block
2.0mm
JP2
LVDS1 LCD Panel Power Select
4-pin Block
2.0mm
Connectors:
Connector
Name
DC_IN3
12V~24V Mini-DIN DC-In Power Jack
USB1/USB2
USB 2.0 Port Connector X4
USB3
USB 3.2 (Gen.2) Port Connector X2
HDMI1
HDMI Port Connector X2
TCP1
USB 3.2 (Gen.2) Type-C Port Connector X2
*Support DP ALT Mode
LAN2/LAN1
2.5GbE RJ-45 LAN Connector X2
AUDIO1
Line-out/MIC Combo Audio Jack
DCIN2
Internal 12V~24V ATX-type Power Connector
CPUFAN1
CPUFAN Connector
SATA1
SATAIII Port Connector
SATAPW1
SATA HDD Power-Out Connector

7
Headers & Wafers:
Header
Name
Description
Pitch
JW_FP1
Front Panel Header (PWR LED/ HD
LED/Power Button /Reset)
9-pin Block
2.54mm
FP_AUDIO1
Front Panel Audio Header
9-pin Block
2.0mm
SPEAK_CON1
3W 8ΩAmplifier Wafer
4-pin Block
2.0mm
JLANLED1
LAN Activity LED Header
4-pin Block
2.0mm
FP_USB1
USB 2.0 Port Header
9-pin Block
2.0mm
FP_USB2
USB 2.0 Port Header
4-pin Block
2.0mm
PS2KBMS1
PS/2 Keyboard & Mouse Header
6-pin Block
2.0mm
SMBUS1
SMBUS Header
4-pin Block
2.0mm
GPIO_CON1
GPIO/80 Port Header
10-pin Block
2.0mm
COM1/COM2
RS232/422/485 Serial Port Header
9-pin Block
2.0mm
COM3/COM4
/COM5/COM6
RS232 Serial Port Header
9-pin Block
2.0mm
LVDS1
LVDS Port Header
30-pin Block
1.25mm
INVERTER1
Inverter Wafer
8-pin Block
2.0mm

8
Chapter 2
Hardware Installation
2-1 Jumper Settings
JCLR_CMOS (2-pin): Clear CMOS RAM Setting
Pin1
JCLR_CMOS → Clear CMOS
Pin1
1-2 Short: Clear CMOS.
1-2 Open: Normal(default);
JPCOM1/ JPCOM2(4-pin): COM1 /COM2 Port Pin9 Function Select
JPCOM1 → COM1 Header Pin-9 VCC
JPCOM2 → COM2 Header Pin-9 VCC
4-6 Closed:
RI= 12V.
6
4
2
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
3
1
5
6
4
2
3
5
1
5
3
1
6
4
2
JPCOM1
JPCOM2
COM1
JCLR_CMOS
COM2

9
JATX_AT1 (3-pin): AT Mode /ATX Mode Select
1
3
1
3
JAT_ATX1 → ATX/AT Mode Select
1-2 Closed: ATX Mode Selected(default);
2-3 Closed: AT Mode Selected.
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
JCASE1 (2-pin): Case Open Message Display Function
JCASE1 → Case Open Detection
CASE OPEN
GND
Pin1
Pin (1&2) Short:When Case open function pin short to GND, the Case open function was
detected. When used, needs to enter BIOS and enable ‘Case Open Detect’function. In this
case if your case is removed, next time when you restart your computer, a message will be
displayed on screen to inform you of this.
JATX_AT1
JCASE1

10
J80PORT1 (2-pin): GPIO_CON 80 Port/GPIO Function Select
Pin1
J80PORT1 → GPIO/80 Function Select
Pin1
1-2 Closed: GPIO_CON1= GPIO Port(Defaut).
1-2 Open: GPIO_CON1= 80 Port;
JME1 (2-pin): ME Features Select
Pin1
JME1 → ME Features Select
Pin1
1-2 Closed: Disable ME Features.
1-2 Open: Enable ME Features;
J80PORT1
JME1

11
JP1 (4-pin): LVDS Inverter BACKLIGHT VCC Select
JP2 (4-pin): LVDS LCD Panel Power VCC Select
*Note:Maximum current limit is 2A while using 3.3V/5V/12V working voltage
*Warning! Wrong voltage setting will result in screen burn out.
JP1
JP2

12
2-2 Connectors, Headers and Wafers
2-2-1 Rear I/O Panel Connectors
Rear Panel Connectors
Icon
Name
Function
Mini-DIN
Power Jack
For user to connect compatible power adapter to
provide power supply for the system.
Type-A USB 2.0 Port
To connect USB keyboard, mouse or other devices
compatible with USB 2.0 specification.
Type-A USB 3.2
(Gen.2) Port
To connect USB keyboard, mouse or other devices
compatible with USB 3.2 (Gen.2) specification. Ports
support up to 10Gbps data transfer rate.
HDMI2.0b Port
To connect display device that support HDMI2.0b
specification.
12V~24V DC-in
Power Jack
USB 2.0 Ports
USB 3.2 (Gen.2)
Ports
HDMI Ports
USB 3.2 (Gen.2)
Type-C Ports
Support ALT
mode
2.5GbE
RJ-45 LAN Ports
(LAN1: I225V)
Line-Out/MIC Combo
Audio Jack
2.5GbE
RJ-45 LAN Ports
(LAN2: I225-LM)

13
Type-C USB 3.2
(Gen.2) & DP 1.4a Port
Type-C USB3.2(Gen.2) port also supports DP ALT
mode & PD 5V/3A
2.5Gbps
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for Network
connection which supports10/100/1000/2500 Mbps
Ethernet data transfer rate (*Note: 2.5Gbps is only
supported with CAT 5e UTP cable).
Line_Out/MIC Combo
Audio Jack
This connector can functions as audio Line-Out jack
and MIC jack with compatible cables & devices.
(1) DCIN3 (4-pin): Mini-DIN 12V~24V Wide-Voltage DC-In Power Connector
Pin1
Pin2
Pin3
Pin4
Pin No.
Definition
1
+12V~24V DC_IN
2
+12V~24V DC_IN
3
GND
4
GND
Warning!!
The board has a 12V~24V DC-in power connector (DCIN3) on I/O back panel and an internal
12V~24V power connector (DCIN2). User can only connect one type of compatible power
supply to one of them to power the system.
DCIN3

14
(2) 2.5GbE RJ-45 Ethernet Connectors
** There are two LED next to the RJ-45 LAN port. Please refer to the table below for
LAN port LED indications.
For 2.5Gbps RJ-45 LAN port LED Signals:
Activity/Link
LED
Speed
LED
A
B
*Note: 2.5Gbps high-speed transmission rate is only supported over CAT 5e UTP cable.
2.5GbE
RJ-45 LAN Ports
(LAN1: I225V)
2.5GbE
RJ-45 LAN Ports
(LAN2: I225-LM)

15
2-2-2 Motherboard Internal Connectors
(1) DCIN2 (4-pin block): Internal 12V~24V Wide-Voltage Power Connector
Pin1
2
3
4
Pin No.
Definition
1
GND
2
GND
3
+12V~24V
4
+12V~24V
(2) CPUFAN1 (4-pin):CPU Fan Connector
Pin1
GND
+12V Fan Power
Fan Speed
Control
CPUFAN1
DCIN2