JETWAY MI09-30 Series User manual

MI09-30/32 Series
User’s Manual
No. G03-MI09-F
Rev: 2.0
Release date: November 1, 2021
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii
ENVIRONMENTAL SAFETY INSTRUCTION................................................................................... iii
ENVIRONMENTAL PROTECTION ANNOUCEMENT.................................................................... iii
USER’S NOTICE.................................................................................................................................... iv
MANUAL REVISION INFORMATION................................................................................................ iv
ITEM CHECKLIST..................................................................................................................................iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 GENERAL SPECIFICATIONS............................................................................................. 1
1-2 LAYOUT DIAGRAM...............................................................................................................2
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................................ 6
2-2 MOTHERBOARD INTERNAL CONNECTORS & WAFERS.......................................... 8
2-3 HEADER PIN DEFINITION................................................................................................... 11
2-4 MAXIMUM VOLTAGE & CURRENT LIMIT....................................................................... 13
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP............................................................................................................. 14
3-2 BIOS MENU SCREEN........................................................................................................... 15
3-3 FUNCTION KEYS...................................................................................................................15
3-4 GETTING HELP......................................................................................................................16
3-5 MENU BARS........................................................................................................................... 16
3-6 MAIN MENU............................................................................................................................ 16
3-7 ADVANCED MENU................................................................................................................17
3-8 CHIPSET MENU..................................................................................................................... 25
3-9 SECURITY MENU.................................................................................................................. 27
3-10 BOOT MENU...........................................................................................................................29
3-11 SAVE & EXIT MENU..............................................................................................................30
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 Second Edition November 1, 2021
Item Checklist
Motherboard
Cable(s)
I/O Back panel shield

1
Chapter 1
Introduction of the Motherboard
1-1 General Specifications
Spec
Description
Design
Slim Mini-ITX form factor; PCB size: 17 x17cm
Chipset
Intel H470 Chipset
CPU Socket
Intel LGA 1200 Socket supports 10th/11th Core
i9/i7/i5/i3/Pentium/Celeron Comet Lake-S & Rocket
Lake-S processors (Max. 65W TDP)
*Note:for detailed CPU support information please visit our website
Memory Slots
2*DDR4 SO-DIMM slot support 2* DDR4 SDRAM SO-DIMM
Maximum frequency:2933/2666/2400MHz(depends on CPU
support)
Maximum capacity: up to 64GB
Support dual channel function
Expansion
Slots
PCIE1: 1 * PCI-Express x4 slot
M2E: 1* M.2 E-key type-2230 (PCIex1/USB2.0) slot with support
for CNVi function
Storage
4*SATAIII 6Gb/s port (SATA1/2/3/4)
M2M:1* M.2 M-key slot,type-2260/2280 (SATA/PCIex4) slot
LAN Chip
1* Intel i219V GbE
Audio Chip
Integrated with C-Media HS-100B USB Audio Chip
BIOS
AMI 256M Bit AMI Flash ROM
Multi I/O
Rear Panel I/O:
1* 12V~19V wide voltage DC-IN power jack
1* 1GbE RJ-45 LAN port
3* Type-A USB 3.2 (Gen.2) 10Gbps port
1* Type-C USB 3.2 (Gen.1) 5Gbps port
1* Display port
1* HDMI 1.4 port
1* Line-Out port
1* MIC port
Internal I/O Connectors & Headers:
1 *2-pin 12V~19V internal power connector
1* SATA power-out connector
1* CPU FAN wafer & 1* System FAN wafer
1* Monitor switch wafer
1* LVDS connector
1* LVDS inverter wafer (FPD)
1* Front panel header
1* RS232/422/485 COM port header
1* BL_SW Brightness control header
1* 19-Pin USB 3.2 (Gen.1) header for 2* USB 3.2 (Gen.1) 5Gbps
port
2* 9-Pin USB 2.0 header for 4* USB 2.0 expansion ports
1* 4-Pin USB 2.0 header for 1* USB 2.0 expansion ports

2
1* Front panel audio header
TPM 2.0 Function
Optional for MI09-32 Series
1-2 Layout Diagram
Rear IO Diagram
Icon
Name
Function
12V~19V DC-in
Power Jack
For user to connect compatible power adapter to
provide power supply for the system.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection.
Type-A USB 3.2
(Gen.2) Port
To connect USB keyboard, mouse or other
devices compatible with USB 3.2 specification.
Type-C USB 3.2
(Gen.1) Port
To connect USB keyboard, mouse or other
devices compatible with USB 3.2 specification.
Display Port
For user to the system to corresponding display
device with compatible DP cable.
HDMI 1.4 Port
To connect display device that support HDMI
specification.
*Line-Out
For user to connect external speaker, earphones,
etc to transfer system audio output.
*MIC-In
User can connect microphone device to this port.
*Note:Rear IO Line-Out & MIC-In ports co-lay with FP_AUDIO(Line-out & MIC-In function), but only
one of the settings function at the same time. User can choose either rear I/O Line-Out & MIC-In port or
Line-Out/MIC-In drawn from FP_AUDIO but not both of them.
12V~19V
DC-IN
Power Jack
RJ-45
LAN Port
USB 3.2 Gen.2 Ports
(Type-A)
USB 3.2 Gen.2 Port
(Type-A)
USB 3.2 Gen.1 Port
(Type-C)
Display Port
HDMI Port
Line-Out
MIC-In

3
Motherboard Internal Diagram-Front
*Rear IO
Connector
(Refer to Page-2)
2*DDR4
SODIMM Slots
LGA 1200
CPU Socket
PCI Express x4 Slot
(PCIE1)
USB 3.2 (Gen.1)
Header
SATAIII Ports
Serial Port
Header
LVDS
Connector
Inverter Wafer
(FPD)
Front Panel
Header
USB 2.0
Header
USB 2.0
Header
USB 2.0
Header
Internal DC-In
Power Connector
(ATX2P)
M.2 M-Key Slot
(M2M)
M.2 E-Key Slot
(M2E)
Front Panel
Audio Header
SYSFAN1
Wafer
CPUFAN1
Wafer
SATA
Power-Out
Connector
BL_SW
Header
MON-SW
Wafer

4
Motherboard Jumper Position:
*Note: The diagrams in the manual are mostly taken from MI09-30 series unless
otherwise stated.
Jumper
Jumper
Name
Description
Pitch
JBAT
Clear CMOS RAM Settings
3-pin Block
2.0mm
JP1
ME Features Select
2-pin Block
2.0mm
JAT_ATX
ATX/AT Mode Select
3-pin Block
2.0mm
LCD_VCC
LVDS PANEL VCC Select
3-pin Block
2.54mm
FPD_PWR
LVDS INVERTER Backlight VCC Select
3-pin Block
2.54mm
JP1
LCD_VCC
JBAT
JAT_ATX
FPD_PWR

5
Connectors & Wafers
P/N
Name
DCIN
12V~19V Internal DC-IN Power Jack
LAN1
1GbE RJ-45 LAN Port
USB31_1
Type-A USB 3.2 (Gen.2) Port X2
USB31_2
Type-A USB 3.2 (Gen.2) Port
USBC1
Type-C USB 3.2 (Gen.1) Port
DP1
Display Port
HDMI1
HDMI 1.4 Port
HOUT1
Audio Line Out Port
HMIC1
Audio MIC In Port
ATX2P
Internal 12V~19V Internal DC-IN Power Connector
SATA1/2/3/4
SATAIII Port Connector
SATA_PWR
SATA Power Out Connector
CPU_FAN1
CPU FAN Wafer
SYS_FAN1
System FAN Wafer
MON_SW
Monitor Switch Wafer
LVDS
LVDS Connector
FPD
LVDS Inverter Wafer
Headers
P/N
Name
Description
Pitch
SYS_PANEL(System
Front Panel Header)
PWR LED/ HD LED/ Power
Button /Reset
9-pin Block
2.54mm
COM1
RS232/422/485
Serial Port Header
9-pin Block
2.0mm
BL_SW
Brightness Control
Switch Header
2-pin Block
2.54mm
FP_USB1
USB 3.2 (Gen.1) Port Header
19-pin Block
2.0mm
FP_USB2/ FP_USB3
USB 2.0 Port Header
9-pin Block
2.0mm
FP_USB4
USB 2.0 Port Header
4-pin Block
2.54mm
FP_AUDIO
Front Panel Audio Header
9-pin Block
2.54mm

6
Chapter 2
Hardware Installation
2-1 Jumper Setting
JBAT (3-pin): Clear CMOS RAM Settings
1
3
1
3
1-2 Closed: Normal;
;
2-3 Closed: Clear CMOS.
JBAT → Clear CM OS Settings
JP1(2-pin): ME Features Select
Pin1
JP1 → ME Features Select
Pin1
1-2 Closed: Disable ME Features.
1-2 Open: Enable ME Features(Default);
JAT_ATX (3-pin): AT Mode /ATX Mode Select
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
JAT_ATX
JBAT
JP1

7
LCD_VCC(3-pin): LVDS Panel Power VCC Select
1
3
1
3
2-3 Closed: VCC=+5V.
LCD_VCC → LVDS Panel Power VCC Select
1-2 Closed: VCC=+3.3V;
FPD_PWR(3-pin): LVDS Inverter Backlight VCC Select
1
3
1
3
FPD_PWR → LVDS Inverter VCC Select
1-2 Closed: VCC=+12V;
;
2-3 Closed: VCC=Power Adapter VCC.
LCD_VCC
FPD_PWR

8
2-2 Motherboard Internal Connectors & Wafers
(1) ATX2P (2-pin block): Internal 12V~19V power connector
(2) SATA1/2/3/4(7-pin): SATAIII Port connector
These are high-speed SATAIII ports that support 6GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
(3) SATA_PWR (15-pin block): SATA power connector
Pin1
SATA Power Out
Connector
*Note:Maximum current limit is 2A while using 5V working voltage and 1Awhile
using 12V working voltage .
ATX2P
SATA1
SATA3
SATA4
SATA2
SATA_PWR

9
(4) CPU_FAN1 (4-pin): CPU FAN Wafer
+12V Fan Power
GND
Fan Speed
Control
Pin1
(5) SYS_FAN1 (4-pin): System FAN Wafer
Fan Speed
GND
Pin1
+12V Fan Power
Control
(6) MON_SW (2-Pin): Monitor Switch Wafer
MON_SW is for LVDS display switch.
CPU_FAN1
MON_SW
SYSFAN1

10
(7) LVDS(40-pin): 48-bit LVDS Connector
Pin No.
Pin Define
Pin 40
LVDS_DDC_DATA
Pin 39
NC
Pin 38
LVDS_BKLT_PWR option
Pin 37
LVDS_BKLT_PWR option
Pin 36
LVDS_BKLT_PWR option
Pin 35
LVDS_CLKBN
Pin 34
LVDS_CLKBP
Pin 33
LCD_BKLT_PWM
Pin 32
LCD_BKLT_EN
Pin 31
LVDS_DDC_CLK
Pin 30
GND
Pin 29
GND
Pin 28
GND
Pin 27
LVDS_CLKAN
Pin 26
LVDS_CLKAP
Pin 25
GND
Pin 24
GND
Pin 23
GND
Pin 22
EDID_3V3 Option
Pin 21
NC
Pin 20
LCD_VCC
Pin 19
LCD_VCC
Pin 18
LCD_VCC
Pin 17
GND
Pin 16
LVDSB _DATAN0
Pin 15
LVDSB_DATAP0
Pin 14
LVDSB _DATAN1
Pin 13
LVDSB_DATAP1
Pin 12
LVDSB _DATAN2
Pin 11
LVDSB_DATAP2
Pin 10
LVDSB _DATAN3
Pin 9
LVDSB_DATAP3
Pin 8
LVDSA_DATAN0
Pin 7
LVDSA_DATAP0
Pin 6
LVDSA_DATAN1
Pin 5
LVDSA_DATAP1
Pin 4
LVDSA_DATAN2
Pin 3
LVDSA_DATAP2
Pin 2
LVDSA_DATAN3
Pin 1
LVDSA_DATAP3
LVDS

11
(8) FPD (8-pin): LVDS Inverter Connector
Warning! Find Pin-1 location of the inverter and make sure that the installation direction is correct!
Otherwise serious harm will occur to the board/display panel!!
2-3 Header Pin Definition
(1) SYS_PANEL (9-pin): System Front Panel Header
(2) COM1(9-Pin): RS232/RS422/RS485 Serial Port Header
Pin NO.
RS232
*RS422
(optional)
*RS485
(optional)
Pin 1
DCD
TX-
DATA-
Pin 2
RXD
TX+
DATA+
Pin 3
TXD
RX+
NC
Pin 4
DTR
RX-
NC
Pin 5
GND
GND
GND
Pin 6
DSR
NC
NC
Pin 7
RTS
NC
NC
Pin 8
CTS
NC
NC
Pin 9
RI
NC
NC
6
Pin 1
*Note: COM header can function as RS232/422/485 port header. In normal settings COM functions
as RS232 header. With compatible COM cable COM can function as RS422 or RS 485 header. User
also needs to go to BIOS to set ‘Transmission Mode Select’ (refer to Page-20) at first, before using
specialized cable to connect different pins of this port.
FPD
COM1
SYS_PANEL

12
(3) BL_SW (2-pin): Brightness Control Switch Header
BRIGHTNESS UP
Pin1
BRIGHTNESS DOWN
(4) FP_USB1(19-pin): USB 3.2 (Gen.1) Port Wafer
SSRX1-
SSRX1+
GND
SSTX1-
SSTX1+
GND
D1-
D1+
VBUS
10
Pin1
NC
D2+
D2-
GND
SSTX2+
SSTX2-
GND
SSRX2+
SSRX2-
VBUS
11
(5) FP_USB2/FP_USB3 (9-pin): USB 2.0 Port Header
-DATA
NC
GND
+DATA
GND
VCC
+DATA
Pin 1
VCC
-DATA
2
(6) FP_USB4 (4-pin): USB 2.0 Port Header
FP_USB2
FP_USB1
FP_USB3
FP_USB4
BL_SW

13
(7) FP_AUDIO (9-pin): Line-Out, MIC-In Header
This header connects to Front Panel Line-out, MIC-In connector with cable.
Pin 1
MIC2-L
LINE OUT2-L
MIC2-R
LINE OUT
2-R
NC
GND
NC
NC
NC
2
*Note:FP_AUDIO (Line-out & MIC-In function) co-lay with rear IO Line-Out & MIC ports, but only one
of the settings function at the same time. User can choose either Line-Out/MIC-In drawn from
FP_AUDIO or directly from the rear I/O but not both of them.
2-4 Maximum Voltage & Current Limit
Below is a list of maximum voltage & Current Limit specification for motherboard
interface (including but not limited to slots, connectors and headers) for setup
reference:
Parts
Working Voltage
Current Support
USB Ports from
USB31_1
5V
1.5A
USB31_2
5V
1.5A
USBC1
5V
1.5A
FP_USB1
5V
1.5A
FP_USB2/3/4
5V
1.5A
SATA_PWR
5V
2A
12V
1A
FPD (via jumper FPD_PWR)
12V/Power Adapter VCC
3A
SYS_PANEL
5V
1A
CPU_FAN1
12V
1.5A
SYS_FAN1
12V
1.5A
M2E
3.3V
2A
M2M
3.3V
2A
FP_AUDIO

14
Chapter 3
Introducing BIOS
Notice! The BIOS options in this manual are for reference only. Different
configurations may lead to difference in BIOS screen and BIOS
screens in manuals are usually the first BIOS version when the board
is released and may be different from your purchased motherboard.
Users are welcome to download the latest BIOS version form our
official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program
is a bridge between motherboard and operating system. When you start the computer,
the BIOS program will gain control. The BIOS first operates an auto-diagnostic test
called POST (power on self test) for all the necessary hardware, it detects the entire
hardware device and configures the parameters of the hardware synchronization.
Only when these tasks are completed done it gives up control of the computer to
operating system (OS). Since the BIOS is the only channel for hardware and software
to communicate, it is the key factor for system stability, and in ensuring that your
system performance as its best.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup,
restart the system to try again by turning it OFF then ON or pressing the “RESET”
button on the system case. You may also restart by simultaneously pressing <Ctrl>,
<Alt> and <Delete> keys. If you do not press the keys at the correct time and the
system does not boot, an error message will be displayed and you will again be asked
to
Press <Del> to enter Setup; press < F7> to enter pop-up Boot menu.
BIOS Boot Menu Screen (boot device options please refer to actual configuration)

15
3-2 BIOS Menu Screen
The following diagram show a general BIOS menu screen:
3-3 Function Keys
In the above BIOS Setup main menu of, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a
short description of the function keys you may use here:
Press (left, right) to select screen.
Press  (up, down) to choose, in the main menu, the option you want to confirm
or to modify.
Press <Enter> to select.
Press <+>/<–> keys when you want to modify the BIOS parameters for the active
option.
[F1]: General help.
[F2]: Previous values.
[F3]: Optimized defaults.
[F4]: Save & Exit.
Press <Esc> to exit from BIOS Setup.
Menu Bar
Menu Items
Current Setting Value
Function Keys
General Help Items

16
3-4 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the top right
corner the screen.
Status Page Setup Menu/Option Page Setup Menu
Press【F1】to pop up a small help window that describes the appropriate keys to use
and the possible selections for the highlighted item. To exit the Help Window, press
<Esc>.
3-5 Menu Bars
There are six menu bars on top of BIOS screen:
Main
To change system basic configuration
Advanced
To change system advanced configuration
Chipset
To change chipset configuration
Security
Password settings
Boot
To change boot settings
Save & Exit
Save setting, loading and exit options.
User can press the right or left arrow key on the keyboard to switch from menu bar.
The selected one is highlighted.
3-6 Main Menu
Main menu screen includes some basic system information. Highlight the item and
then use the <+> or <-> and numerical keyboard keys to select the value you want in
each item.