JETWAY JNLH61S-6C Series User manual

JNLH61S-6C Series
User’s Manual
No. G03-NLH61S-F
Revision: 1.0
Release date: December 3, 2021
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at anytime without notice, and should not be construed as a commitment by manufacturer.

ii
TABLE OF CONTENT
ENVIRONMENTAL SAFETY INSTRUCTION ....................................................................... iii
ENVIRONMENTAL PROTECTION ANNOUCEMENT...........................................................iii
USER’S NOTICE .................................................................................................................. iv
MANUAL REVISION INFORMATION...................................................................................iv
ITEM CHECKLIST................................................................................................................ iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 SPECIFICATION .................................................................................................... 1
1-2 LAYOUT DIAGRAM ............................................................................................... 2
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................. 5
2-2 CONNECTORS AND HEADERS............................................................................ 7
2-2-1 REAR I/O BACK PANEL CONNECTORS................................................. 7
2-2-2 MOTHERBOARD INTERNAL CONNECTORS………………………………..8
2-2-3 HEADER PIN DEFINITION........................................................................ 11
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP.............................................................................................. 16
3-2 BIOS MENU SCREEN............................................................................................ 17
3-3 FUNCTION KEYS................................................................................................... 17
3-4 GETTING HELP ..................................................................................................... 17
3-5 MENU BARS.......................................................................................................... 18
3-6 MAIN MENU........................................................................................................... 18
3-7 ADVANCED MENU ................................................................................................ 19
3-8 CHIPSET MENU..................................................................................................... 26
3-9 BOOT MENU.......................................................................................................... 30
3-10 SECURITY MENU .................................................................................................. 31
3-11 SAVE & EXIT MENU .............................................................................................. 31

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion
Revision History
Date
1.0
First Edition
December 3, 2021
Item Checklist
☑Motherboard
☑Cable(s)
☑I/O Back panel shield

1
Chapter 1
Introduction of the Motherboard
1-1 Specification
Spec
Description
Design
ATX form factor; PCB size: 30.5 x22.0 cm
Chipset
Intel®H61 Express Chipset
CPU Socket
Support Intel® LGA 1155 Socket supports Sandy/IVY Bridge Core
Processor Max 90W
* for detailed CPU support information please visit our website
Memory Slot
DDRIII RAM module slot x 2
Supporting four DDRIII 1066/1333MHz RAM Module expandable to32
GB (Maximum)
Support dual-channel function
Expansion
Slots
1 pcs* PCI-Express x16 slot (PE1)
1 pcs* PCI-Express x1 slot (PE2)
5 pcs *32-bit PCI slot (PCI1/2/3/4/5)
1 pcs* Full-size Mini-PCIE slot (MINI_PCIE)
Storage
4 * SATAII port
LAN Chips
Integrated dual RTL8111H PCI-E Gigabit LAN chips
Supports Fast Ethernet LAN function provide10/100/ 1000Mbps data
transfer rate
HD Audio Chip
Realtek HD 6-channel Audio Codec integrated
Audio driver and utility included
BIOS
32M Bit DIP Flash ROM
Multi I/O
Rear Panel I/O:
1* PS/2 keyboard connector & 1* PS/2 mouse connector
1* VGA port connector
1* DVI-D port connector
4* USB 2.0 port connector
2* RJ-45 LAN connector
2* Serial port connector (COM1 port supports RS232
function,COM3 port supports RS232/485/422 function )
3* Audio connector (Line-in, Line-out, MIC)
Internal I/O Connectors& Headers:
1 *24-pin main power connector
1 *8-pin 12V Power connector
1* Front panel audio header x1
1* HDMI-SPDIF header x1
1* Parallel port header x1
1* GPIO header x1
2* 9-pin USB 2.0 header x2
1*POWER LED1+Speaker header
4* COM port header (COM2/5/6 headersupports RS 232 function,
COM4 headersupports RS 232/485/422 function )
3* Fan header

2
1-2 Layout Diagram
Rear IO Diagram
Internal Diagram:
PS/2
Mouse Port
PS/2
Keyboard Port
VGA Port
DVI-D Port
RJ-45LAN Ports
USB2.0 Ports
Serial Port
(COM3)
Serial Port
(COM1)
Line-IN
Line-OUT
MIC-IN
PS/2 Mouse Port over
PS/2 Keyboard Port
VGA Port over
DVI–D Port
RJ-45 LAN Ports
Over USB 2.0 Ports
RJ-45 LAN Ports
Over USB 2.0 Ports
Serial Ports Ports
Audio Connectors
Front Panel Audio Header
HDMI S/PDIF Header
32-bit PCI Slots
Parallel Header
GPIO Header
PWR LED Header
Speaker Header
Front Panel Header
SYS FAN1 Header
USB 2.0 Headers
(
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
Serial Ports
(COM2/4/6/5) (
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
1
0
/
9
)
SATAII Ports (
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
1
0
/
9
)
AT_MODE (
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
1
0
/
9
)
PCI Express 2.0 x1 Slot (PE2)
PCI Express x16 Slot (PE1)
SYS FAN2 Header
Intel H61Chipset
(
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
1
0
/
9
)
Full-size Mini-PCIE Slot (MINI-PCIE) (
C
O
M
2
/
4
/
7
/
8
/
6
/
5
/
1
0
/
9
)
DDRIII DIMM Slot*2
ATX Power Connector
CPUFAN Header
ATX 12V Power Connector

3
Motherboard Jumper Position
Jumper
Jumper
Name
Description
JBAT
CMOS RAM Clear Function Setting
3-Pin Block(2.54 pitch)
JP1
KB/MS Power on Function Setting
3-pin Block(2.54 pitch)
JP2
COM1 Port Pin9 Function Select
4-pin Block(2.54 pitch)
JP3
COM3 Port Pin9 Function Select
4-pin Block(2.54 pitch)
JP4
Mini PCI-E Slot VCC3.3V/3.3VSB Select
3-pin Block(2.54 pitch)
JP6
COM2 Header Pin9 Function Select
4-pin Block(2.54 pitch)
JP7
COM4 Header Pin9 Function Select
4-pin Block(2.54 pitch)
JP1
JP2
JP3
JBAT
JP6
JP7
JP4

4
Connectors
Connector
Name
ATXPWR1
ATX Power Connector
ATX12V1
ATX 12V Power Connector
SATA1
SATAII Connector
SATA2/3/4
SATAII Connector X3
VGA
Video Graphic Attach Connector
DVI
DVI-D Port Connector
COM1
RS232 Serial Port Connector
COM3
RS232/422/485 Serial Port Connector
UL1(Top)/UL2(Top)
RJ-45 LAN Connector X2
UL1(Middle & Bottom)
/UL2(Middle & Bottom)
USB 2.0 Port Connector X4
AUDIO
Line Out /Line In /MIC
Audio Connector
Headers
Header
Name
Description
FP_AUDIO
Front Panel Audio Header
9-pin Block(2.54 pitch)
HDMI_SPDIF
HDMI_SPDIF Out Header
2-pin Block(2.54 pitch)
GPIO_CON
GPIO Header
10-pin Block(2.54 pitch)
PARALLEL
Parallel Port Header
25-pin Block(2.54 pitch)
JW_FP
(Front Panel Header)
PWR LED/ HD LED/
Power Button /Reset
9-pin Block(2.54 pitch)
PWRLED1
Power LED Header
3-pin Block(2.54 pitch)
SPEAK1
Speaker Header
4-pin Block(2.54 pitch)
USB2
USB 2.0 Header
9-pin Block(2.54 pitch)
USB3
USB 2.0 Header
9-pin Block(2.54 pitch)
COM 2/6/5
RS232 Serial Port Connector
9-pin Block(2.54 pitch)
COM4
RS232/422/485 Serial Port
Connector
9-pin Block(2.54 pitch)
CPUFAN1
CPUFAN Header
4-pin Block(2.54 pitch)
SYSFAN1/SYSFAN2
System FAN Header
3-pin Block(2.54 pitch)

5
Chapter 2
Hardware Installation
2-1 Jumper Setting
JBAT (3-pin): Clear CMOS Function Settings (2.54 pitch)
3
1
1
3
1-2 Closed: Closed:Normal
2-3 Closed:Clear CMOS.
JP1 (3-pin): KB/MS Power on Function Setting (2.54 pitch)
3
1
1
3
1-2 Closed: KB/MS Power on Function Disabled (default)
2-3 Closed: KB/MS Power on Function Enabled
JP2 (4-pin): COM1 Port Pin9 Function Select (2.54 pitch)
4-6 Closed:
RI=12V
3-4 Closed:
RI=5V
2-4 Closed:
RI=RS232
1
3
5
4
6
2
6
4
2
5
3
1
6
4
2
5
3
1
JP1
JP2
JBAT

6
JP3 (4-pin): COM3 Port Pin9 Function Select (2.54 pitch)
4-6 Closed:
RI=12V
3-4 Closed:
RI=5V
2-4 Closed:
RI=RS232
1
3
5
4
6
2
6
4
2
5
3
1
6
4
2
5
3
1
JP4 (3-pin): Mini PCI-E Slot VCC 3.3V/3.3 VSB Select (2.54 pitch)
3
1
1
3
1-2 Closed: MINI PC-E VCC=3.3V
2-3 Closed: MINI PC-E VCC=3.3VSB
JP6 (4-pin): COM2 Header Pin9 Function Select (2.54 pitch)
3
6
4
5
2
1
2-4 Closed:
RI=RS232
3-4 Closed:
RI=5V
4-6 Closed:
RI=12V.
6
4
2
5
3
1
6
4
2
5
3
1
JP3
JP4
JP6

7
JP7 (4-pin): COM4 Header Pin9 Function Select (2.54 pitch)
3
6
4
5
2
1
2-4 Closed:
RI=RS232
3-4 Closed:
RI=5V
4-6 Closed:
RI=12V.
6
4
2
5
3
1
6
4
2
5
3
1
2-2 Connectors and Headers
2-2-1 Rear I/O Back Panel Connectors
(1) PS/2 Mouse & PS/2 Keyboard Connector: KB/MS
The connectors are for PS/2 keyboard port (Purple) and PS/2 Mouse port
(Green).
(2) D-Sub 15-pin VGA Connector: VGA
VGA connector is the 15-pin D-subminiature female connector; it is for the
display devices, such as the CRT monitor, LCD monitor and so on.
(3) Digital Visual Interface: DVI
This interface standard designed to maximize the visual quality of digital display
devices such as flat panel LCD computer displays and digital projectors.
(4) RJ-45 LAN Port Connectors: UL1 (Top)/UL2 (Top)
The connectors are standard RJ-45 connectors for Network.
(5) USB 2.0 Port Connector: UL1 (Middle & Bottom)/ UL2 (Middle & Bottom)
The connectors are 4-pin connector that connects USB devices to the system
board.
JP7
PS/2
Mouse Port
PS/2
Keyboard Port
DVI-D Port
VGA Port
RJ-45 LAN Ports
USB2.0 Ports
Serial Port
(COM3)
Serial Port
(COM1)
Line-IN
Line-OUT
MIC-IN

8
(6) Serial port Connector: COM3 /COM1
COM1 (9-pin Block): RS232 Port; COM3 (9-pin Block): RS232/422/485 Port
COM1 port can function as RS232 port.
COM3 port can function as RS232/422/485 port. In normal settings COM3
functions as RS232 port. With compatible COM cable COM3 can function as
RS422 or RS 485 port.
User also needs to go to BIOS to set ‘Transmission Mode Select’ for COM3
(refer to Page-24)at first, before using specialized cable to connect different pins of
this port.
1
2
3
4
5
6
7
8
9
RS232 DCD#
RS232 SIN
RS232 SOUT
RS232 DTR#
GND
RS232 RI#
RS232 CTS#
RS232 RTS#
RS232 DSR#
RS232 Mode
(COM1/COM3)
RS422 Mode
(*COM3)
RS485 Mode
(*COM3)
Pin1
GND
RS422 RX-(B)
RS422 RX+(A)
RS422 TX+(A)
RS422 TX-(B)
Pin1
GND
RS485 D+(A)
RS485 D-(B)
Pin1
(7) Line-In, Lin-Out, MIC Audio connectors: AUDIO1
Color
Name
Function
Blue
Line-in
Audio input to sound chip
Green
Line-out
Audio output to speaker
Pink
MIC
Microphone Connector
2-2-2 Motherboard Internal Connectors
(1) ATXPWR (24-pin block): Main Power Connector
ATX Power Supply connector: This is a new defined 24-pins connector that usually
comes with ATX case. The ATX Power Supply allows using soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned
on, the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.

9
** We recommend that you use an ATX 12V Specification 2.0-compliant power
supply unit (PSU) with a minimum of 350W power rating. This type has 24-pin and 4-
pin power plugs.
** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the
20-pin power plug can provide at least 15A on +12V and the power supply unit has a
minimum power rating of 350W. The system may become unstable or may not boot
up if the power is inadequate.
** If you are using a 20-pin power plug, please refer to Figure1 for power supply
connection. Power plug form power supply and power connectors from motherboard
both adopt key design to avoid mistake installation. You can insert the power plug into
the connector with ease only in the right direction. If the direction is wrong it is hard to
fit in and if you make the connection by force if is possible.
Figure1：20-pin power plug Figure 2：24-pin power plug
ATXPWR1

10
(2) ATX12V (8-pin block): 12V Power Connector
This is a new defined 8-pin connector that usually comes with ATX Power Supply that
supports extra 12V voltage to maintain system power consumption. Without this
connector might cause system unstable because the power supply can not provide
sufficient current for system.
(3) SATA1/2/3/4:SATAII Port connector
These connectors are high-speed SATAII ports that support 3GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
ATX12V
SATA2
SATA3
SATA4
SATA1

11
2-2-3 Header Pin Definition
(1) FP_AUDIO (9-pin): Line-Out, MIC-In Header (2.54 pitch)
This header is connected to Front Panel Line-out, MIC connector with cable.
Pin1
2
MIC1-R
LINE OUT-L
MIC1-L
LINE OUT-R
NC
GND
NC
NC
NC
(2) HDMI_SPDIF (2-pin): HDMI-SPDIF Out header (2.54 pitch)
Pin1
SPDIF
GND
(3) GPIO_CON (10-pin): GPIO Header (2.54 pitch)
Pin1
2
GPIO
GND
GPIO
GPIO
GPIO
GPIO
VCC
GPIO
GPIO
GPIO
10
FP_AUDIO
HDMI_SPDIF
GPIO_CON

12
(4) PARALLEL (25-pin): Parallel Port Header (2.54 pitch)
Pin NO.
Pin Definition
Pin NO.
Pin Definition
Pin 1
STB-
Pin 14
AFD-
Pin 2
PRD0
Pin 15
ERR-
Pin 3
PRD1
Pin 16
INIT-
Pin 4
PRD2
Pin 17
SLIN-
Pin 5
PRD3
Pin 18
GND
Pin 6
PRD4
Pin 19
GND
Pin 7
PRD5
Pin 20
GND
Pin 8
PRD6
Pin 21
GND
Pin 9
PRD7
Pin 22
GND
Pin 10
ACK-
Pin 23
GND
Pin 11
BUSY
Pin 24
GND
Pin 12
PE
Pin 25
GND
Pin 13
SLCT
Pin14
Pin1
Parallel Port Header
PARALLEL

13
(5) JW-FP (9-pin): Front Panel Header (2.54 pitch)
Pin1
HDDLED+
VCC
HDDLED-
GND
RSTSW
PWRLED+
PWRBT
PWRLED-
GND
(6) PWRLED1 (3-pin): PWR LED Header (2.54 pitch)
Pin1
PWRLED+
PWRLED-
PWRLED-
(7) SPEAK1 (4-pin): Speaker Header (2.54 pitch)
Pin1
SPEAK+
NC
NC
SPEAK
JW_FP
PWRLED1
SPEAK1

14
(8) USB 2.0 Port Headers (9-pin): USB2/USB3 (2.54 pitch)
Pin1
VCC
-DATA
+DATA
GND
VCC
+DATA
-DATA
GND
NC
(9) COM2/4/6/5: Serial Port Header (2.54 pitch)
COM4:RS232/422/485 serial port header;
COM2/6/5: RS232 serial port header only.
In most cases COM4 serves as RS232 serial port. For RS422 & RS485 function user
also needs to go to BIOS to set ‘Transmission Mode Select’ as [RS422] or [RS485]
before connecting compatible COM cable to corresponding header.
Pin NO.
RS232
*RS422
(COM4 only)
*RS485
(COM4 only)
Pin 1
DCD
TX-
DATA-
Pin 2
RXD
TX+
DATA+
Pin 3
TXD
RX+
NC
Pin 4
DTR
RX-
NC
Pin 5
GND
GND
GND
Pin 6
DSR
NC
NC
Pin 7
RTS
NC
NC
Pin 8
CTS
NC
NC
Pin 9
RI
NC
NC
USB2
USB3
Pin1
Pin6
COM5
COM6
COM4
COM2

15
(10) CPUFAN1 (4-pin): CPUFAN Header (2.54 pitch)
Pin1
GND
+12V Power
Fan Speed
Control
(11) SYSFAN1/SYSFAN2 (3-pin): SYSFAN Headers (2.54 pitch)
Pin1
SYSFAN1
Power Fan
+12V Fan
GND
SYSFAN2
Pin1
GND
+12V Fan Power
Fan Speed
CPUFAN1
SYSFAN2
SYSFAN1

16
Chapter 3
Introducing BIOS
Notice! The BIOS options in this manual are for reference only. Different configurations may
lead to difference in BIOS screen and BIOS screens in manuals are usually the first
BIOS version when the board is released and may be different from your purchased
motherboard. Users are welcome to download the latest BIOS version form our
official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge
between motherboard and operating system. When you start the computer, the BIOS program will
gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all
the necessary hardware, it detects the entire hardware device and configures the parameters of
the hardware synchronization. Only when these tasks are completed done it gives up control of
the computer to operating system (OS). Since the BIOS is the only channel for hardware and
software to communicate, it is the key factor for system stability, and in ensuring that your system
performance as its best.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the “RESET”button on the system case.
You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not
press the keys at the correct time and the system does not boot, an error message will be
displayed and you will again be asked to
Press <Del> to enter Setup/ Press <F7> to enter Popup Menu.