JETWAY MI225 Series User manual

MI225 Series
User’s Manual
NO. G03-MI225-F
Revision: 1.0
Release date: June 13, 2023
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

ii
ENVIRONMENTAL SAFETY INSTRUCTION............................................................................. iii
USER’S NOTICE...............................................................................................................................iv
MANUAL REVISION INFORMATION...........................................................................................iv
ITEM CHECKLIST............................................................................................................................ iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD.........................................................................................1
1-2 SPECIFICATION.................................................................................................................... 2
1-3 LAYOUT DIAGRAM...............................................................................................................4
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................................ 11
2-2 CONNECTORS, HEADERS AND WAFERS..................................................................... 15
2-2-1 REAR I/O BACK PANEL CONNECTORS......................................................... 15
2-2-2 MOTHERBOARD INTERNAL CONNECTORS................................................. 19
2-2-3 PIN DEFINITION FOR HEADERS & WAFERS.................................................22
2-3 MAXIMUM VOLTAGE & CURRENT LIMIT....................................................................... 28
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP................................................................................................................ 29
3-2 BIOS MENU SCREEN...........................................................................................................30
3-3 FUNCTION KEYS...................................................................................................................31
3-4 GETTING HELP......................................................................................................................31
3-5 MENU BAR..............................................................................................................................32
3-6 MAIN MENU............................................................................................................................ 32
3-7 ADVANCED MENU................................................................................................................33
3-8 CHIPSET MENU..................................................................................................................... 46
3-9 SECURITY MENU.................................................................................................................. 49
3-10 BOOT MENU...........................................................................................................................52
3-11 SAVE & EXIT MENU..............................................................................................................53
3-12 MEBX........................................................................................................................................54
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The temperature comes from the
request of the chassis and thermal solution)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition June 13, 2023
Item Checklist
Motherboard
DVD for motherboard utilities
User’s Manual
Cable(s)
I/O Back panel shield

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
Intel®LGA1700 Socket supports 12th /13th Gen. Core Processor (Max. 65W TDPs
under 180A)
Support 2* DDR5 4800MHz SO-DIMM up to 64GB
Integrated with 1* Intel®i219-LM GbE & 1* Intel®i225V 2.5GbE LAN chips
Support 1* VGA, 1* HDMI, 1* DP, 1* LVDS/eDP Output
Support 6* COM (COM1 support RS232/422/485)
MI225Q670X/R680X series: total support up to 6* USB3.2 (Gen.2), 2* USB3.2
(Gen.1), 3* USB2.0 ports
MI225H610X series: total support up to 2* USB3.2 (Gen.2), 2* USB3.2 (Gen.1), 5*
USB2.0 ports
MI225Q670X/R680X series: 4 * SATAIII (6Gb/s) ports with support for RAID 0, 1, 5,
10 mode & 2* M.2 (M-key) slots; 1* M.2 (E-key) & 1* M.2 (B-key) slot along with SIM
card holder; 1* PCIE Gen.4 x16 slot
MI225H610X series: 4 * SATAIII (6Gb/s) ports & 1* M.2 (M-key) slot; 1* M.2 (E-key)
& 1* M.2 (B-key) slot along with SIM card holder; 1* PCIE Gen.4 x16 slot
Support onboard TPM 2.0 (*optional)
Support Smart FAN function
Supports ACPI S3 Function
Compliance with ErP Standard
Support Watchdog Timer Technology

2
1-2 Specification
Spec
Description
Design
Mini-ITX form factor; 10-layers; PCB size: 17.0x17.0cm
Chipset
MI225H610X Series: Intel®H610E/H610 Chipset
MI225Q670X Series: Intel®Q670E Chipset
MI225R680X Series: Intel®R680E Chipset
CPU Socket
Intel®LGA 1700 Socket supports 12th/13th Gen. Core™ i7/i5/i3
/Pentium™/Celeron™ processors (Max.65W TDPs under 180A)
*Note: for detailed CPU support information please visit our website.
Memory Slot
2* DDR5 SO-DIMM slot
Support 2* DDR5 4800MHz SO-DIMM up to 64GB
Support dual channel function
*Note: MI225R680X series support ECC.
Expansion
Slot
PCIE1:1* PCIE Gen.4 x16 slot (PCIE1)
M2E1:1* M.2 E-key,type-2230 slot(USB2.0/PCIe Gen.3 x1 interface) supports
CNVi
M2B1:1* M.2 B-key, type-3042 slot supports supports 4G Module
(MI225Q670X/R680X series: PCIe Gen.3 x1/USB3.2 Gen.2/USB2.0 interface;
MI225H610X series: PCIe Gen.3 x1 interface only).
SIMCARDB1:1* Nano-SIM card slot;co-function with M2B1 slot
Storage
4*SATAIII 6Gb/s port support (*SATA1/2/3/4)
*Note: MI225Q670X/R680X series support RAID 0/1/5/10 mode.
M2M1: 1* M.2 M-key,type-2280 slot (PCIe Gen.3x4 interface) supports NVMe
*M2M2:1* M.2 M-Key, type-2242 slot (PCIe Gen.4 x4/SATA interface) supports
NVMe
*Note: M2M2 slot is only available to MI225Q670X/R680X series.
Graphics
Intel®UHD Graphics, shared memory for:
1* DP 1.4a
1* HDMI 2.0b
1* VGA
1* LVDS/eDP
* Note: MI225Q670X/R680X series support Quad Displays; MI225H610X series
support Triple Displays
LAN Chips
Integrated with:
1* Intel®i225V 2.5GbE PCI-E LAN chip of providing 10/100/1000/2500Mbps

3
Ethernet data transfer rate
*Note: 2500Mbps high-speed transmission rate is only supported over CAT 5e UTP
cable.
1* Intel®i219-LM Gigabit PHY LAN chip of providing 10/100/1000Mbps Ethernet
data transfer rate
Support Fast Ethernet LAN function
Audio Chip
Realtek HD Audio Codec integrated
Audio driver and utility included
BIOS
AMI 256Mb Flash ROM
Multi I/O
Rear Panel I/O:
2* COM port(COM1_2; COM1: RS232/422/485 supports 5V/12V TTL)
1* HDMI port, 1*VGA & 1* DP port
MI225Q670X/R680X: 6* USB 3.2 Gen.2 port
MI225H610X: 2* USB 3.2 Gen.2 port & 2* USB 3.2 Gen.1 port + 2* USB 2.0 port
1* 1.0GbE RJ-45 LAN port (LAN1 from UL1)
2.5GbE RJ-45 LAN port (LAN2 from UL2)
1* 3-jack audio connector (Line-in, Line-out, MIC)
Internal I/O Connectors, Headers & Wafers:
1 *24-pin main power connector
1 *4-pin 12V power connector
1* CPUFAN1 connector & 1* SYSFAN1 connector
1* CMOS battery connector
1* Front panel header
1* Front panel audio header
1* HDMI_SPDIF header
4* RS232 COM port header (COM3/4/5/6)
1* 9-Pin USB 2.0 header for 2* USB 2.0 ports +1* 4-Pin USB 2.0 header for 1*
USB 2.0 port
MI225Q670X/R680X:1*19-Pin USB 3.2 (Gen.1) header for 2* USB 3.2 (Gen.1)
ports
1* GPIO header
1* PS2 Keyboard & Mouse header
1* SMBUS header
1* LVDS/EDP wafer (LVDS_EDP) & 1*Inverter wafer(INVERTER1)
TPM 2.0
Optional for MI225R6802, MI225Q6702 &MI225H6102 Series
OS Support
for detailed OS support information please visit our website for latest update

4
1-3 Layout Diagram
Rear IO Diagram
For MI225R680X/ MI225Q670X Series:
For MI225H610X Series:
VGA Port
COM1
RS232/422/485
Serial Port
COM2
RS232
Serial Port
HDMI Port
DisplayPort
USB 3.2 (Gen.2)
Ports
Line-IN
Line-OUT
MIC-IN
LAN1: 1.0GbE
RJ-45 LAN Port
(2.5 GbE)
LAN2: 2.5GbE
RJ-45 LAN Port
(2.5 GbE)
USB 3.2 (Gen.2)
Ports
VGA Port
COM1
RS232/422/485
Serial Port
COM2
RS232
Serial Port
HDMI Port
DisplayPort
USB 2.0 Ports
Line-IN
Line-OUT
MIC-IN
LAN1: 1.0GbE
RJ-45 LAN Port
(2.5 GbE)
LAN2: 2.5GbE
RJ-45 LAN Port
(2.5 GbE)
USB 3.2 (Gen.2)
Ports
USB 3.2 (Gen.1)
Ports

5
Motherboard Internal Diagram-Front
MI225Q670X/R680X Series:
LGA1700
CPU Socket
LVDS_EDP
PCIE1: PCI Express
Gen4x16 Slot
Front Panel
Header
GPIO
Header
M.2 M-Key Slot
(M2M1)
M.2 M-Key Slot
(*M2M2)
USB2.0 Port
Headers
RS232 Serial Port Headers
(COM3/4/5/6)
Front Panel
Audio Header
M.2 B-Key Slot
(M2B1)
M.2 E-Key Slot
(M2E1)
PS/2 KBMS Header
SATAIII Ports
(SATA1/2/3/4)
SMBUS Header
SYSFAN1
CPUFAN1
*Rear IO
Connector
(Refer to Page-4)
DDR5
SODIMM Slot x 2
BATCON
ATX 12V
Power Connector
ATX Main Power
Connector
INVERTER1
HDMI_SPDIF
Header
USB 3.2(Gen.1)
Header
(*FP_USB3)

6
MI225H610X Series:
LGA1700
CPU Socket
LVDS_EDP
PCIE1: PCI Express
Gen4x16 Slot
Front Panel
Header
GPIO
Header
M.2 M-Key Slot
(M2M1)
USB2.0 Port
Headers
RS232 Serial Port Headers
(COM3/4/5/6)
Front Panel
Audio Header
M.2 B-Key Slot
(M2B1)
M.2 E-Key Slot
(M2E1)
PS/2 KBMS Header
SATAIII Ports
(SATA1/2/3/4)
SMBUS Header
SYSFAN1
CPUFAN1
*Rear IO
Connector
(Refer to Page-4)
DDR5
SODIMM Slot x 2
BATCON
ATX 12V
Power Connector
ATX Main Power
Connector
INVERTER1
HDMI_SPDIF
Header

7
Motherboard Internal Diagram-Back
*Note: 1. SIM card slot only workable along with M.2 B-key slot; 2. M2M2 Slot & FP_USB3 header are only
available to MI225Q670X/R680X series).
*SIMCARDB1

8
Motherboard Jumper Position
*Note:The diagrams in the manual are mostly taken from MI225Q670X/R680X series for illustration
purpose,unless otherwise stated.
JBAT1
COPEN
JP4
JP2
JP6
JP5
JP1
JAT_ATX

9
Jumper
P/N
Name
Description
Pitch
JBAT1
Clear CMOS RAM Settings
3-pin Block
2.0mm
JP1
Flash Descriptor Security Override
2-pin Block
2.0mm
JAT_ATX
ATX Mode / AT Mode Select
3-pin Block
2.0mm
COPEN
Case Open Message Display Function
2-pin Block
2.54mm
JP4
GPIO Header Function Select
2-pin Block
2.0mm
JP6
COM1 Port Pin9 Function Select
4-pin Block
2.0mm
JP2
LVDS_EDP PANEL VCC Select
4-pin Block
2.0mm
JP5
INVERTER1 Backlight VCC Select
3-pin Block
2.0mm
Connectors
P/N
Name
COM1_2
Top(COM1): RS232/422/485 Serial Port
Bottom(COM2): RS232 Serial Port
VGA
VGA Port
HDMI
HDMI Port
USB3
MI225Q670X/R680X:
Top &Middle: USB 3.2(Gen.2) Port X2
MI225H610X:
Top & Middle: USB 2.0 Port X2
DP
Bottom: DisplayPort
UL1
Top: 1.0 GbE RJ-45 LAN Port
Middle & Bottom: USB 3.2 (Gen.2) Port X2
UL2
MI225Q670X/R680X:
Top: 2.5 GbE RJ-45 LAN Port
Middle & Bottom: USB 3.2 (Gen.2) Port X2
MI225H610X:
Top: 2.5 GbE RJ-45 LAN Port
Middle & Bottom:USB 3.2 (Gen.1) Port X2
AUDIO
Top: Line-in Connector
Middle: Line-out Connector
Bottom: MIC Connector
ATXPWR1
24-Pin ATX Main Power Connector

10
ATX12V
Internal 12V Power Connector
SATA1/2/3/4
SATAIII Connector
CPUFAN1
CPU Fan Connector
SYSFAN1
System Fan Connector
BATCON
CMOS Battery Connector
Headers & Wafers
P/N
Name
Description
Pitch
FP
(Front Panel Header)
PWR LED/ HD LED/Power Button /Reset
9-pin Block
2.54mm
FP_AUDIO
Front Panel Audio Header
9-pin Block
2.0mm
HDMI_SPDIF
HDMI_SPDIF Header
2-pin Block
2.54mm
COM3/4/5/6
RS232 Serial Port Header
9-pin Block
2.0mm
FP_USB1/2
USB2.0 Port Header
9-pin Block
2.0mm
MI225Q670X/R680X:
FP_USB3
USB 3.2 (Gen.1) Port Header
19-pin Block
2.0mm
GPIO
GPIO Port Header
10-pin Block
2.0mm
PS2KBMS
PS2 Keyboard & Mouse Header
6-pin Block
2.0mm
SMBUS1
SMBUS Header
5-pin Block
2.0mm
LVDS_EDP
LVDS/EDP Wafer
30-pin Block
1.25mm
INVERTER1
Inverter Wafer
8-pin Block
2.0mm

11
Chapter 2
Hardware Installation
2-1 Jumper Setting
JBAT1 (3-pin): Clear CMOS RAM Settings
JP1 (2-pin): Flash Descriptor Security Override
Pin1
JP1 → Flash Override
Pin1
1-2 Closed: Disable Security Measures
in the Flash Descriptor(Override).
1
-2 Open: Enable Security Measures
in the Flash Descriptor(Default);
JBAT1
JP1

12
JAT_ATX (3-pin): AT Mode /ATX Mode Select
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
COPEN (2-pin): Case Open Message Display Function
COPEN → Case Open Detection
CASE OPEN
GND
Pin1
JAT_ATX
COPEN

13
Pin 1-2 Short:When Case open function pin short to GND, the Case open function was detected. When
Used, needs to enter BIOS and enable ‘Case Open Detect’function. In this case if your case is removed,
next time when you restart your computer, a message will be displayed on screen to inform you of this.
JP4(2-pin): GPIO Header Function Select
Pin1
JP4 → GPIO Function Select
Pin1
1-2 Closed: Function as GPIO Port.
1-2 Open: Function as 80 Port;
JP6(4-pin): COM1 Port Pin9 Function Select
JP6 → COM1 Port Pin-9
4-6 Closed:
RI= 12V.
1
3
5
3-4 Closed:
RI= 5V;
2-4 Closed:
RI=RS232;
4
6
2
1
3
5
4
2
6
2
4
6
1
3
5
COM1
(Top)
JP6
JP4

14
JP2 (4-pin): LVDS_EDP Power VCC Select
4-6 Closed:
VCC= 12V.
1
3
5
3-4 Closed:
VCC=5V;
2-4 Closed:
VCC=3.3V;
4
6
2
1
3
5
4
2
6
2
4
6
1
3
5
JP2 → LVDS_EDP Power VCC Select
**Warning! Wrong voltage setting will result in screen burn out.
JP5(3-pin):INVERTER1 Backlight VCC Select
**Warning! Wrong voltage setting will result in screen burn out.
JP2
JP5

15
2-2 Connectors, Headers & Wafers
2-2-1 Rear I/O Back Panel Connectors
*Refer to Page-4 Rear IO Diagram
Icon
Name
Function
Serial Port
Mainly for user to connect external MODEM or other
devices that supports
Serial Communications Interface.
*Note: COM1 (Top) supports RS232/422/485
function.
VGA Port
To connect display device that support VGA
specification.
HDMI Port
To connect display device that support HDMI
specification.
Display Port
To the system to corresponding display device with
compatible DP cable.
1.0Gbps
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection which
supports10/100/1000Mbps Ethernet data transfer
rate.
2.5Gbps
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection which
supports10/100/1000/2500 Mbps Ethernet data
transfer rate (*Note:2.5Gbps is only supported with
CAT 5e UTP cable).
USB 3.2 (Gen.2)
Port
To connect USB keyboard, mouse or other devices
compatible with USB 3.2 (Gen.2) specification. Ports
support up to 10Gbps data transfer rate.