JML uber scoot S300 User manual

USER
MANUAL
300
NOTE: Product images are for demonstration purposes only and may not reect exact appearance of actual product.
Specications subject to change without notice.
READ AND UNDERSTAND THE
ENTIRE MANUAL BEFORE RIDING
SUITABLE FOR AGES 13+

1.
IMPORTANT
BATTERY CARE AND MAINTENANCE
1. Make sure that your UBER SCOOT S300 is fully charged prior to initial use. The rst charge will take 12 hours. Wait for the
full 12 hour charge period before unplugging.
2. Always charge your UBER SCOOT S300 after every use.
3. DO NOT leave your UBER SCOOT S300 charging for more than 5 hours (except for rst 12 hour charge).
4. Should you wish to store your UBER SCOOT S300, charge it beforehand and make sure to charge once every 14 days.
5. Only inate the tires to max 60 psi.
6. Do NOT store in freezing or below freezing temperatures. Freezing temperatures will permanently damage the battery.
This manual contains vital information regarding product care as well as best riding practices, riding conditions, and
precautionary measures. Read through this entire manual before riding, and make sure to heed all warnings. Failure
to do so may result in your UBER SCOOT S300 not being covered by guarantee.
WARNINGS
The UBER SCOOT S300 is not intended to be used on public roads where there are cars, buses, taxis or any other licensed motor
vehicles. Make sure to familiarise yourself with the trac rules and regulations in your area to determine where it is safe for you
to ride your scooter. This is not a toy. Riding the UBER SCOOT S300 can result in serious injury or even death regardless of the
ability of the rider, any factory fault, any precautions taken or conditions in which they (the rider) were riding in. Make sure to
check that all nuts and bolts are tightly fastened before use, that your brakes are in proper working condition, and that you are
both able and competent to handle this scooter. Parents should be made aware that this scooter is not for children under the
age of 13, and further still, that riders above this age should show a suitable degree of awareness, skill and ability to handle a
ride-on of this nature. Assembly should be supervised by an adult. Do not exceed the weight limit of 100kg. The rider’s weight
does not necessarily mean that their size is appropriate to maintain control of the scooter. Do not touch the breaks or motor
when in use or directly after use as these parts may be hot. Keep away from small children. Recommended age is 13+. It is a
parent decision to allow his or her child to ride this product and this should be based on the child's maturity, skill and ability to
follow rules. Outdoor use only. Never risk damaging surfaces such as carpet or orring by using the product indoors.
RIDING CONDITIONS, METHOD AND APPROPRIATE APPAREL
Make sure to use personal, protective equipment in the form of elbow and knee pads as well as a helmet and appropriate
footwear. Gloves and goggles are recommended.
Riders will become accustomed to riding the UBER SCOOT S300 over time. Accidents can occur when given to someone who
has never ridden a scooter before. Exercise caution when allowing a rst-time rider to get onto the UBER SCOOT S300. The rider
should be instructed on how to ride the UBER SCOOT S300 (see full details on“HOW TO RIDE YOUR UBER SCOOT S300” below).
Use caution when riding, and make sure to always be aware of your surroundings so as to avoid any pedestrians, other riders,
animals or xed obstacles that may cause you, or you may cause, any injury. The UBER SCOOT S300 is not designed to
withstand any extreme manoeuvres. Do not attempt to perform any tricks, wheelies, bunny hops or any other extreme
manoeuvres on the UBER SCOOT S300. Evidence of such abuse will render your guarantee void.
Assess riding conditions before making use of the UBER SCOOT S300, and do not ride through any gravel, mud, water, sand or
on any o-road surface. Do not ride your UBER SCOOT S300 in the rain, or through any adverse weather conditions. The
electrical and drive components could be damaged by riding through the aforementioned elements or surfaces and will render
your guarantee void. Do not ride at night or when visibility is limited. Do not ride near steps or swimming pools.
HOW TO RIDE YOUR UBER SCOOT S300
The UBER SCOOT S300 has a variable-speed accelerator (throttle) like that found on a motorcycle. You can control your speed
precisely by slowly opening the throttle. Opening the throttle further will result in increased speed. Do not snap the throttle
open suddenly as this will rapidly project the scooter forward. This may result in you losing control of the UBER SCOOT S300
and can result in damage to property or cause you serious injury.
Before turningthe UBER SCOOT S300 on make sure that the scooter is aimed towards an open space with nothing in front of
you. Put one foot on the deck and hold the handlebars rmly. Familiarise yourself with the brakes before switching on your
UBER SCOOT S300. Hold the accelerator rmly and slowly twist it open. As the scooter starts to move forward and you have
enough speed to balance, place your second foot onto the deck. Slowly open the throttle until you get to the required speed
for the conditions in which you are riding, whilst maintaining a speed suitable for your ability. Build your speed up gradually as
you become familiar with the scooter. Practise using the brakes while you are going slowly. Avoid opening the throttle to its
maximum until you are well accustomed to the scooters handling and braking. Fully opening the throttle will result in your
batteries discharging rapidly, and your range will be adversely aected.

Place the
handlebar onto
the handle stem Tighten the
handlebar knob
4 5
1
8
6
9
4
7
Front wheel
Installation requires adult supervision. To dismantle the scooter, ensure the power is o.
Ensure the power is o and not being ridden before making any adjustments.
Rear wheel
3
2
INSTALLING THE HANDLEBAR
Put down the foot stand
Open the scooter
fully so that the
fold mechanism
holes line up
Place the fold mechanism pin fully
into the hole and tighten the knob.
ATTENTION: Ensure the fold
mechanism pin is correctly inserted
and tightened before riding.
FAMILIARISING YOURSELF WITH YOUR UBER SCOOT S300
2.
1. Throttle
2. Handlebar tightening knob
3. Hand-operated rear brake
4. Handle stem
5. Brake caliper
6. 300W Motor
7. Foot stand
8. Fuse/Reset
9. On/O switch
10. Rechargeable 24V Battery
11. Fold mechanism
1 2 3
10
11
5

3.
To charge, plug the charger into the wall
(1), and the charger into the charging port
(2) located on the right-hand side of the
UBER SCOOT S300 just beneath the deck.
Prior to rst use your UBER SCOOT S300 must be charged for 12 hours. Even if the green light comes on, disregard this and
leave the unit charging for the full 12 hours before unplugging.
After the rst charge, charge your UBER SCOOT S300 until the green light appears (this means that your scooter is fully
charged). The UBER SCOOT S300 may be left charging for up to 5 hours. Do not exceed this period as your batteries may suer
irreparable damage and this treatment will render your guarantee void.
1. For the rst charge your UBER SCOOT S300 must be left to charge for 12 hours.
2. From there onwards charge your UBER SCOOT S300 until the green light appears on the charger. Do not charge your UBER SCOOT
S300 for a period longer than 5 hours, this may cause irreparable damage to your batteries and will not be covered by guarantee.
3. Do not allow your batteries to go into “deep discharge”. This occurs when a rider does not charge the unit immediately after the
batteries have been depleted. This will cause irreparable damage to your batteries and will not be covered by guarantee.
4. Make sure that you charge your UBER SCOOT S300 prior to storing it. Charge your scooter at least once every 14 days. Not charging
the UBER SCOOT S300 every 14 days may result in irreparable damage to your batteries which will not be covered by guarantee.
To increase the range on your batteries, be sure to charge your UBER SCOOT S300 whenever the scooter is not in use. On
returning from a ride, charge your UBER SCOOT S300 immediately. Consistent charging will build up the range of your batteries.
These batteries can be use normally under the temperature of -20~40°C. Non-Spillable Battery. UN/NA Number: UN2800
CHARGING
DISPOSAL AND THE ENVIRONMENT
BATTERY CARE
Proper chain care will increase the life and improve the performance of your UBER SCOOT S300.
1. Always keep the chain lubricated with a good chain spray (either motorcycle or bicycle-grade).
2. Make sure that the chain is tight with about 2-3mm of“play”.
3. It is recommended that you do not attempt to tighten the chain yourself, but rather visit a Service Centre for this
adjustment as this is a specialized operation.
4. Incorrectly aligning the rear wheel and/or over tightening the chain will cause damage to the scooter that will not be
covered by your guarantee.
CHAIN CARE
TYRE CARE
1 2
This product is covered by the waste electrical and electronic equipment (WEEE) regulations. It should not be discarded with normal
household waste, but taken to your local collection centre for recycling. For further information, please contact your local authority
or approved disposal agency.
Only inate the tyres to the correct psi (max 60 psi).

4.
IMPORTANT: Please do not attempt to adjust the end of the brake cable that is located on the underside of the scooter.
Please contact JML customer services if you have any queries.
HOW TO BRAKE
Pulling the brakes sharply at high speed can cause the rear wheel to lock which may result in a “at spot” on the rear wheel.
To avoid this, pull gently on the brake, this will decrease the chances of skidding and ultimately preventing at-spotting.
Flat-spotting on the rear wheel will not be covered under guarantee.
The UBER SCOOT S300 has a rear wheel brake-pad system.
To tighten your brakes, loosen the lock nut (A) by turning it anti-clockwise until it spins freely. Now turn the tensioning bolt (B)
outwards until the brake is correctly adjusted. Finally, tighten the lock nut to lock the adjustment in place.
To loosen your brakes, loosen the lock nut (A). Turn the tensioning bolt (B) inward and the brake will loosen. Now tighten the
lock nut to lock the adjustment in place.
ADJUSTING YOUR BRAKES & BRAKING
If your UBER SCOOT S300 happens to suddenly stop working, check the fuse located below the deck on the left-hand side of
the scooter above the charging port. The fuse may have shorted if the motor was overloaded. If so, replace the fuse and correct
the riding conditions that caused the overload. Avoid repeatedly tripping the breaker. Should you experience further issues
please contact JML customer services.
Glass Fuse 40A 250V
FUSE/RESET
B
A
Fuse

5.
Problem Possible Cause Solution
Scooter does not run
Scooter suddenly
stopped working while
in use
Short run time
(less than15 minutes
per charge)
Scooter runs sluggishly
Undercharged battery
Tripped circuit breaker
Undercharged battery
Riding conditions are too
stressful
Ensure that your scooter is fully charged. The rst charge
should not be longer than 12 hours and subsequent charges
should not be more than 5 hours
Check all connectors. If charging, make sure that the charger is
correctly connected to the charging port, and that there is
power to the charger
Check all wires and connectors to make sure they are tight
The circuit breaker (fuse) will automatically shut o the power
if the motor is overloaded
An excessive overload, such as too heavy a rider or a very steep
hill, could cause the motor to overheat. If the scooter suddenly
stops running, check the fuse and replace if necessary. Correct
the conditions that caused the breaker to trip and avoid
repeatedly tripping the breaker
Charge the battery. A new battery must be charged for 12
hours before using the scooter for the rst time. Subsequent
charges should not be more than 5 hours
Check all wires and connectors. Make sure the battery
connector is tightly plugged into the charger connector and
that the charger is plugged into the wall
Battery is old and will not
accept full charge
Make sure power ow to the wall outlet is on
Use only on solid, at, clean and dry surfaces such as
pavements or level ground
Sometimes the scooter
doesn’t run but other
times it does
Loose wires or connectors Check all wires around the motor and all connectors to make
sure they are tight
Scooter makes loud
noises or grinding sounds
Chain is too dry Apply a lubricant to the chain
Scooter is overloaded Make sure you do not overload the scooter by allowing more
than one rider at a time, exceeding the 100kg maximum weight
limit, going up a steep hill or towing objects behind the scooter.
If the scooter is overloaded, the circuit breaker (fuse) may trip
and shut o the power to the motor. Correct the riding
conditions that caused the overload, check the fuse and replace
if necessary. Avoid repeatedly tripping circuit breaker
TROUBLE SHOOTING
Even with proper care, a rechargeable battery does not last
forever. Average battery life is 1 to 2 years depending on
scooter use and conditions. Use only genuine replacement
battery

6.
Please ensure that your sealed lead-acid batteries are disposed of in an environmentally friendly manner. Hazardous materials
such as lead, acid and plastic can cause harm to the environment. Do not expose batteries to re as they may leak or explode
and may injure those close by and/or cause damage to nearby surroundings. Consult your local authorities to understand how
to dispose of your batteries.
BATTERY DISPOSAL
Never wash this product with a hose, rather use a damp rag to wipe the product clean, paying particular attention in ensuring
that the motor and batteries are kept free of water and moisture.
CLEANING
This product is unconditionally guaranteed for one year against all defects of workmanship and materials. This guarantee does
not cover normal wear and tear, tires, tubes or cables, or any damage, failure or loss caused by improper assembly,
maintenance, storage, or use of the Uber Scooter.
GUARANTEE
PbPb
MODEL NO S300/ES04
WATTAGE
BATTERY CHARGER
SUITABLE FOR AGES
PRODUCT WEIGHT
MAX WEIGHT LOAD
USAGE
APPLICATION
MAX WEIGHT
CHARGE TIME
CHARGE CYCLES
MAX RIDING SPEED
MAX TYRE PRESSURE
300W 24V
24V 7AH SLA (110V -240V)
100KG
12 HOURS FIRST TIME. 4-6 HOURS THEREAFTER.
APPROXIMATELY 250
Up to 15 MPH / Up to 24 KMH (APPROX 40 MINS)
60 PSI
13+
18KGS
RECREACTION
100KGS
OUTDOOR USE ONLY WITH ADULT SUPERVISION. DO NOT RIDE ON PUBLIC
ROADS WHERE CARS, BUSES, TAXIS OR ANY OTHER LICENSED MOTOR
VECHICLES ARE. DO NOT RIDE AT NIGHT OR IN POOR VISIBILITY.
SCOOTER

300
Pb Pb
Distributed by JML
Unit 1 Eastside, Port of Tyne, South Shields, NE33 5SP
Customer Services:
UK: 0800 781 7831 (Freephone) ROI: 041-978 0003 (Local rate)
©JohnMillsLtd/PF/08.16/TO/A • Product code: V2143 • Made in China
Model no: S300/ES04 • Batch no: XXXX
Table of contents