John Lewis OXFORD 83501 User manual

1
20598 - 1
1
John Lewis
OXFORD Unit 1x2
Stock number: 83501
Thank you for purchasing this Oxford Unit 1x2. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer from whom
you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.

2
20598 - 1
1
Fittings and parts checklist
1
RIGHT side panel x1
2
LEFT side panel x1
3
Fixed shelf x 1
4
Back panel x 1
5
Base x 1
6
Top x 1
A
Connecting bolts
x 12
F
Angle x 1
B
Camlocks x 12
G
Screws 5x16 x 1
C
Dowels 8x35 x 18
H
Wall plug x 1
D
Plastic feet x 4
I
Screw 5x60 x 1
E
Cover caps x 8
J
Plastic back holder
x 4

3
20598 - 1
1
Step by step assembly instructions
Step One
1. Take the right side panel (1) and lay it on the clean and flat surface with the predriling holes
uppermost.
2. Screw the four connecting bolts (A) into the holes provided.
3. Insert the three dowels (C) into the holes provided.
______________________________________________________________
Step Two
1. Take the fixed shelf (3) and lay it on the clean and flat.
2. Insert the six dowels (C) into the holes provided.

4
20598 - 1
1
______________________________________________________________
Step Three
1. Take the base (5) and lay it on the clean and flat surface.
2. Insert the six dowels (C) into the holes provided.
______________________________________________________________
Step Four
1. Take the right side panel (1) and lay them on the clean and flat surface with the connecting bolt
turned up.
2. Locate the base (5) and fixed shelf (3) onto the right side panel (1) as shown in the picture.
3. Insert the four camlocks (B) into the holes provided.
4. Tighten the four camlocks (B) using the crosshead screwdriver.

5
20598 - 1
1
_____________________________________________________________
Step Five
1. Locate the back panel (4) onto the right side panel (1) and base (5) as shown in the picture.

6
20598 - 1
1
_____________________________________________________________
Step Six
2. Take the left side panel (2) and lay it on the clean and flat surface with the predrilling holes
uppermost.
3. Screw the four connecting bolts (A) into the holes provided.
4. Insert the three dowels (C) into the holes provided.
____________________________________________________________
Step Seven
1. Locate the left side panel (2) onto the base (5) and fixed shelf (3) as shown in the picture.
2. Insert the four camlocks (B) into the holes provided.
3. Tighten the four camlocks (B) using the crosshead screwdriver.
B
B
B
B

7
20598 - 1
1
_____________________________________________________________
Step Eight
1. Insert the four plastic feet (D) into the holes provided.
2. Attach the angle (F) using one screw (G) . Tighten the screw (G) using the crosshead screwdriver.
_____________________________________________________________
Step Nine
1. Turn the carcase of the unit onto its plastic feet.

8
20598 - 1
1
_____________________________________________________________
Step Ten
1. Take the top (6) and lay it on the clean and flat surface with the predriling holes uppermost.
2. Screw the four connecting bolts (A) into the holes provided.
_____________________________________________________________
Step Eleven
1. Locate the top (6) onto the right side panel (1), and left side panel (2) as shown in the picture.
2. Insert the four camlocks (B) into the holes provided.
3. Tighten the four camlocks (B) using the crosshead screwdriver.
B
B
B
B

9
20598 - 1
1
_____________________________________________________________
Step Twelve
1. Insert the four plastic back holder (J) into the top (6) and base (5).
2. Tighten the four plastick back holder (J) using the crosshead screwdriver.
_____________________________________________________________
Step Thirteen
1. Insert the eight cower caps (E) into the holes in the camlocks (B).
The assembly is now complete.
!!!

10
20598 - 1
1
Wall fixing - if in doubt seek professional advice
_____________________________________________________________
1. With help, place the unit against the wall in its finall location and mark the drilll hole positions.
2. Remove the unit and drill a 8mm diameter hole to a depth of 65mm in the marked positions.
3. Insert wall plug supplied.
4. With help, lift the unit up and aligning the holes, fix to the wall using the screws supplied and
tighten fully.
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily
pull away from the
core structure
Brick or Masonry
Use an appropriate
wall plug provided you
are sure your wall is
sound
Cavity wall
Special toggle
wall plugs are
needed. Seek
expert advice