John Lewis Mixit 80324203 User manual

Please check the pack contents before attempting to assemble this product.A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings (cams, dowels and screws) please contact our spare parts
helpline on 0330 005 9435. Opening hours are 9am - 5pm Monday to Friday.
For all other queries, please call John Lewis Customer support on 0345 604 9049
Stock Code: 80324203 - 80324103 - 80324003
Mixit low wide unit
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Small hammer
Drill Eye protection Spirit level
Screwdriver
MXT 70 rev. 03 - 26/02/20
Page 1
Thank you for purchasing this Mixit low wide unit. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.

Metal dowel x 12 Cam lock x 8
Wooden dowel x 12
30mm
Wedgex housing x 8 Wedgex dowel x 8
13mm Euroscrew x 8
Wall xing set x 4
27mm Connector x 2
4MAx15 Connect. screw x 2
A B
C
H I
P P1P2
D E
L
M N O
Support foot x 5
F
25mm Nail x 30
G
Nail guide x 1
30mm Screw x 10 Spacer x 8
Long cam lock x 4
B1
GI
Levelling Wedge x 2
Page 2
MXT 70 rev. 03 - 26/02/20
Fittings checklist

1
1
5
3
3
2
2
4
4
Page 3
MXT 70 rev. 03 - 26/02/20
Parts checklist

A
A
A
1x 2
Page 4
Step by step assembly instructions
Step One
Attach 12x metal dowels (A) into the pre-drilled holes on top/bottom panels (1) as shown.
Use a screwdriver to turn fitting (A) clockwise to fix.
1.
B
Right side
Left side
Bottom
Bottom
4
4
B
B
B
B
C
C
C
C
E
E
Step Two
Place 8x cam lock (B) into the holes on side panels (4) as shown, arrow pointing towards the bolt.
Attach 8x wooden dowels (C) into the pre-drilled holes on side panels (4) as shown.
Fix 4x wedgefix dowels (E) into the holes on side panels (4) as shown.
1.
2.
3.
MXT 70 rev. 03 - 26/02/20

D
D
D
3x 2
E
BI
BI
C
C
5
5
E
BI
Page 5
MXT 70 rev. 03 - 26/02/20
Step by step assembly instructions
Step Three
Attach 8x wedgefix housing (D) into the pre-drilled holes on shelves (3) as shown.1.
Step Four
Place 4x long cam lock (BI) into the holes on divider (5) as shown, arrow pointing towards the bolt.
Ensure long cam lock (BI) is pusched down firmly to base of drill hole.
Attach 4x wooden dowels (C) into the pre-drilled holes on divider (5) as shown.
Attach 4x wedgefix dowels (E) into the holes on divider (5) as shown.
1.
2.
3.

1
1
4
4
5
1
2
B
B
A
2
2
Bottom
Top
Page 6
Step by step assembly instructions
Step Five
Attach panels (5)(4) to top/bottom panels (1) as shown. Ensure metal dowels (A) and wooden dowels (C)
are aligned correctly with the holes of matching parts before attaching.
Secure panels using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
Step Six
Position back panel (2) as shown, back panel holes indicate upper part.1.
MXT 70 rev. 03 - 26/02/20

F
F
F
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
G
2
2
Page 7
MXT 70 rev. 03 - 26/02/20
Step by step assembly instructions
Step Eight (only for base unit)
Attach support foot (L) onto bottom (1) using 30x screws (M).
1.
Step Seven
Attach back panel (2) onto back side of the unit using 30x nails (F), with the help of the nail guide (G).1.
L
L
M
M
M
MM
1

Ø5mm
IH
GI
GI
Page 8
Step by step assembly instructions
Step Nine
With help of an assistant,
carefully stand up the unit upright.
1.
Step Eleven
Fittings have been supplied in order to join units together.
Place units together in their final positon.
Decide position where to drill through using a Ø5 mm bit.
Push the Connector (H) into the hole and then screw Bolt (I) in from the other side, tighten with a screw-
driver.
1.
2.
3.
Step Ten (only for base unit)
Use 2x levelling wedge (GI) to level the unit.1.
MXT 70 rev. 03 - 26/02/20

Page 9
MXT 70 rev. 03 - 26/02/20
Step by step assembly instructions
Wall plug and screw not included. Please see Guide to wall mounting.
O
PP
43 5
21
N
P1
P2
P
P
Spacer (N) are to be used on both wall and base units to
allow for the depth of skirting boards, allowing all of the
units to sit flush with one another.
Step Twelve (only for base unit)
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of two ‘L’
Brackets (P) fitted to the top side of the unit.
Attach the 2x brackets (P) onto the top side of the unit using 4x euroscrew (O).
Pre-fix brackets (P) to wall, Wall plug and screw not included.
Adjust position using (P1), then attach it.
Insert cap (P2)
! IMPORTANT !
Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plug and screw not included. See wall fixing guide at page 12.
1.
2.
3,4.
5.

Page 10
MXT 70 rev. 03 - 26/02/20
Step by step assembly instructions
Wall plug and screw not included. Please see Guide to wall mounting.
O
PP
43 5
21
N
P1
P2
P
P
Spacer (N) are to be used on both wall and base units to
allow for the depth of skirting boards, allowing all of the
units to sit flush with one another.
P
P
Step Thirteen (only for wall unit)
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of two ‘L’
Brackets (P) fitted to the top side of the unit.
Attach the 4x brackets (P) onto the top side of the unit using 8x euroscrew (O).
Pre-fix brackets (P) to wall, Wall plug and screw not included.
Adjust position using (P1), then attach it.
Insert cap (P2)
! IMPORTANT !
Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plug and screw not included. See wall fixing guide at page 12.
1.
2.
3,4.
5.