John Lewis Ollie 80346601 User manual

Ollie Oak Storage Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 35 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock Code:
Double
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Ollie Storage Bed. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product.
803/46601
1

Fittings and parts checklist - Bedstead
Fittings
A
B
C
D
E
F
4mm Allen Key x1
M8 x 22mm Bolt x8
Centre Rail Cup x2
20mm Screws x8
Slat Connectors x14
Cap Ends x28
Parts
1
2
3
4
5
Headboard x 1
Footboard x 1
Side Rail x 2
Slats x 28
Centre Rail x 1

Step by step assembly instructions - Bedstead
Step One
Attach the Centre Rail Cup (2) to the lower rail of the Headboard (1) and Footboard (2) using 20mm Screws (D)
as shown in the diagram below.
D
D
1C
&2
1
C
2
C

Step Two
Attach the Siderails (3) to the Headboard (1) and Footboard (2) using M8 x 15mm
Bolts (B) as shown below. Tighten the Bolts (B) using the 4mm Allen Key (A)
provided.
B
B
3
1
x 4
1
2
3
3

Step Three
Lower the Centre Rail (4) onto the Centre Rail Cups (C) on the Headboard (1) and
Footboard (2) as shown in the diagram below.
C
4
1&2
1
2
3
3
4

Step Four
Starting at the headend, insert the Slat Connectors (E) along the Centre Rail (4).
Ensuring that the Slats (5) are facing curved side up, insert into the Slat
Connector (E). Place a Cap End (F) onto the other end of the Slat (5) and push
down fully into the pre-drilled holes along the Side Rails (3), as shown in the
diagram below. Repeat this process to attach all 28 Slats (5).
E
F
5
5
5
3
3
1
2

Ollie Oak Storage Bed - Drawers

Fittings and parts checklist - Drawers
Fittings
A
B
C
D
E
4mm Allen Key x1
M6 x 30mm Bolt x8
Castors x8
12mm Screws x24
35mm Screws x12
Parts
1
2
3
4
5
Drawer Fronts x 2
Drawer Left Side Panel x2
Drawer Right Side Panel x2
Drawer Back x2
Drawer Bottom x2
PLEASE NOTE: THE DRAWERS COME IN PACKS OF TWO SO THE ABOVE CONTENTS IS WHAT EACH
PACK INCLUDES.

Step One
Attach the Castors (C) to the Drawer Left Panel (2) and Drawer Right Panel (3) using the
12mm Screws (D) and tighten using a screw driver as shown in the diagram below.
23
Step Two
Now attach the Drawer Left Panel (2) and Drawer Right Panel (3) to the Drawer Front (1) using M6 x 30mm
Bolt (B) then tighten using 4mm Allen key as shown below.
3
2
1

Step Three
Slide the Drawer Bottom (5) into the groove along the Drawer Left Panel (2) Drawer Right Panel (3) and
Drawer Front (1) as detailed in the diagram below.
5
1
3
2
Step Four
Attach the Drawer Back (4) to the Drawer Left Panel (2) and Drawer Right Panel (3) using 12mm Screw (D),
35mm Screw (E) and screw driver. Please ensure you slide the Drawer Bottom into the groove on the Drawer
Back (4) before securing.
3
5
2
4
3