John Lewis Mia 810/84103 User manual

Mia Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact your the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock Code: 810/84103
Stock Code: 810/84104
Double
King size
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Mia Bed. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product.

Fitting and parts checklist
A
B
C
D
E
F
M5 Allen Key x 1
M4 Allen Key x 1 Side Caps x 30
Centre Caps x 15
M6 X 25mm Bolts x 2
M6 X 40mm Bolts x 8
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 30
Centre Rail x 1
Legs x 4

Step Two
Place brackets on side rails (3) over pre-inserted bolts in headboard (1) and foot board (2). Tighten bolts
using allen key M5 (B) to secure parts together.
Step by step assembly instructions
Step One
Place wooden legs (6) over the holes in the underside of the headboard (1) and foot board (2) as per below drawing.
M5 (B)
M6 x 40 bolt
M6 x 40 bolt
M6 x 40 bolt
M6 x 40 bolt
(6) x 4
(M6) x 8M4 (A)
M5
BRACKET
SIDE RAIL
3
1
2
AND
1
3
3
2
BRACKET
SIDE RAIL
1
2
3
AND
Allen Key
Bed Leg
Pre-inserted Nut
Head/Foot
Board

M4
M6 x 25mm
Step Three
Insert centre rail (5) into the brackets in the centre of the headboard (1) and foot board (2). Push down fully and
secure in place using M6 x 25mm bolt (E) tighten using allen key M4 (A).
Step Four
Side Caps (30 pcs)
Centre Caps (15 pcs)
SlatS (30pcs)
Centre Rail
S
T
E
P
1
M4
M6 x 25mm
S
T
E
P
2
5
4
D
D
C
4
4
x30
D
4
4
x15
C
4.
C.
D.
E. A.
Push the centre plastic caps (C) into the holes along the centre rail (5). Once in place, insert a slat (4) into the
centre plastic cap followed by a side cap (D). Finally push the side plastic cap into the holes on the side rail (3).
Repeat this process for all slats.
5

Care and Maintenance
Safety Instructions
This Mia bedstead should be cleaned using a soft damp cloth and dried immediately. Do not use a very wet
cloth or allow any liquid contact for a long period of time as this can permanently damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on going discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS 1725:98
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London , SWIE 5NN.
www.johnlewis.com
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by competent adults.
No liability will be accepted for damage or injury caused by incorrectly insalled or assembled furniture.
During assembly children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fitting when doing this.