John Lewis Mixit User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact your the John Lewis Helpline.
his product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
his product takes approximately 70 MINUTES to assemble with 2 PEOPLE.
he fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
John L wis
Stock Code: 80319002 - 80319102 - 80319202
Mixit ch st 4 draw rs
hank you for purchasing this Mixit chest 4 drawers. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
N c ssary Tools
Screwdriver
002030405060708090 00 020 30 40 50
023456
Ruler/tape
measure Small hammer
Drill Eye protection
Spirit level
MXT 04/13
Page 1

Metal dowel x 24 Long cam lock x 8 Wooden dowel x 24
30mm
Short cam lock x 16 30mm Screw x 16 Support foot x 4
Strap x 1 11mm Euroscrew x 16 15mm Screw x 25
25mm Nail x 30 Bumper x 8 Levelling Wedge x 2
Fixing block x 8
27mm Connector x 4 4MAx15 Connect. screw x 4
Pair of rollers 4
A B C
G
L
H
M
D E F
I
N
O P Q
Z2
Z1
Nail guide x 1
P1
Page 2
MXT 04/13
Fittings checklist

1
2
3
4
5
6
7x 4
8x 4
9x 4
10 x 4
11 x 4
Raw
Page 3
MXT 04/13
Parts checklist

1
A
Page 4
Step by step assembly instructi ns
Step One
Attach x metal dowels (A) into the pre-drilled holes on top panel (1) as shown. Use a screwdriver to turn
fitting (A) clockwise to fix.
1.
Step Two
Attach x wooden dowels (C) into the pre-drilled holes on rails (5) (6) as shown.
Place the cam lock (B) into the holes on rails (5) (6) as shown, arrow pointing towards the bolt.
1.
2.
5
6Raw
BB
CC
B
MXT 04/13

B
left side
F
F
3
right side
2
C
C
A
A
B
Z1
Z1
B
Front side
H
H
I
H
Z1
Page 5
MXT 04/13
Step by step assembly instructi ns
Step Three
Attach x metal dowels (A) into the pre-drilled holes on side panels (2) (3) as shown. Use a screwdriver
to turn fitting (A) clockwise to fix.
Attach x support foot (F) into pre-drilled holes on side panels (2) (3) as shown.
Fix 8x runner parts (Z1) to the side panels (2) (3) through holes shown in the detail view using
16x euroscrews (H) and 8x screws (I).
Attach x wooden dowels (C) into the pre-drilled holes on side panels (2) (3) as shown.
Place x cam lock (B) into the holes on side panels (2) (3) as shown, arrow pointing towards the bolt.
1.
2.
3.
.
5.

12
B
A
B
2
3
5
6Raw
12
B
A
B
1
2
3
Page 6
Step by step assembly instructi ns
Step Four
Attach side panels (2) (3) to rails (5) (6) as shown. Ensure metal dowels (A) and wooden dowels (C) are
aligned correctly with the holes of matching parts before attaching.
Secure side panels (2) (3) to rails (5) (6) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
Step Five
Attach top panel (1) onto sides (2) (3) as shown. Ensure metal dowels (A) and wooden dowels (C) are
aligned correctly with the holes of matching parts before attaching.
Secure top panel (1) to sides (2) (3) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
MXT 04/13

LImportant:
The cabinet MUST
be ‘square’ when the
back is attached.
4
L
L
P1
Page 7
MXT 04/13
Step by step assembly instructi ns
Step Six
Position back panel ( ) as shown.1.
Step Seven
Attach back panel ( ) onto back side of the unit using 30x nails (L), with the help of nail guide (P1).
1.
4

N
N
Page 8
Step by step assembly instructi ns
Step Eight
With help of an assistance, carefully stand up the unit upright.1.
Step Nine
Use 2x levelling wedge (N) to level the unit.1.
MXT 04/13

Ø5mm
P
O
Page 9
MXT 04/13
Step by step assembly instructi ns
Step Ten
Fittings have been supplied in order to join units together.
Place units together in their final positon.
Decide position where to drill through using a Ø5 mm bit.
Push the Connector (O) into the hole and then screw Bolt (P) in from the other side, tighten with a
screwdriver.
1.
2.
3.

Top of Unit
W
A
L
L
W
A
L
L
W
A
L
L
G
G
G
I
1
4
Page 10
MXT 04/13
Step by step assembly instructi ns
Step Eleven
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of wall
strap (G) fitted to the Top of the unit.
Secure one end of the wall strap (G) to the wall.
Thread the other end of the wall strap (G) through the gap between the top (1) of the chest
and the back panel ( ).
Working from the front of the chest, fix the wall strap (G) to the underside of the top (1) using the
wall strap screw (I).
Thread the screw through through the end of the wall strap (G) and into the pilot hole in the underside
of the top (1).
Do not fix the wall strap (G) to any other component.
! IMPORTANT !
Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plug and screw not included. See wall fixing guide at page 1 .
1.
2.
3.
.
5.